Plan for the Settlement of Jurisdictional Disputes in the Construction Industry Including Procedural Rules and Regulations COVERING the U.S. and CANADA Approved by the Building and Construction Trades Department, AFL-CIO June 1984 As Amended Through May 2011
Plan for the Settlement of Jurisdictional Disputes in the Construction Industry Including Procedural Rules and Regulations COVERING the U.S. and CANADA Approved by the Building and Construction Trades Department, AFL-CIO June 1984 As Amended Through May 2011
TABLE OF CONTENTS Procedural Rules and Regulations for the Plan for the Settlement of Jurisdictional Disputes in the Construction Industry .............................. 1-15 Plan for the Settlement of Jurisdictional Disputes in the Construction Industry ............. 16-38 Agreements and Decisions of Record ................. 39-176 Index ............................................................... 177-181
1 PROCEDURAL RULES AND REGULATIONS FOR THE PLAN FOR THE SETTLEMENT OF JURISDICTIONAL DISPUTES IN THE CONSTRUCTION INDUSTRY ARTICLE I CONTRACTOR'S RESPONSIBILITY 1. The contractor who has the responsibility for the performance and installation shall make a specific assignment of the work which is included in his contract to a particular union(s). For instance, if contractor A subcontracts certain work to contractor B, then contractor B shall have the responsibility for making the specific assignments for the work included in his contract. If contractor B, in turn, shall subcontract certain work to contractor C, then contractor C shall have the responsibility for making the specific assignment for the work included in his contract. After work has been so assigned, such assignment will be maintained even though the assigning contractor is replaced and such work is subcontracted to another contractor. It is a violation of the Plan for the contractor to hold up disputed work or shut down a project because of a jurisdictional dispute. 2. When a contractor has made an assignment of work, he shall continue the assignment without alteration unless otherwise directed by an arbitrator or there is agreement between the National or International Unions involved. a. Unloading and/or handling of materials to
2 stockpile or storage by a trade for the convenience of the responsible contractor when his employees are not on the job site, or in an emergency situation, shall not be considered to be an original assignment to that trade. b. Starting of work by a trade without a specific assignment by an authorized representative of the responsible contractor shall not be considered an original assignment to that trade, provided that the responsible contractor, or his authorized representative, promptly, and, in any event, within eight working hours following the start of work, takes positive steps to stop further unauthorized performance of the work by that trade. c. The Administrator shall determine all questions of original assignment of work and render decisions regarding same. An appeal of the Administrator's determination of original assignment may be made to an arbitrator in a hearing under the terms and provisions of Article V of the Plan. Notice of the appeal shall be filed with the Administrator within seven (7) days of issuance of the determination. The appeal shall be processed only if the responsible contractor has complied with the Administrator's determination. d. Criteria to be used in making assignments of work are set forth in Article V, Section 8, of the Plan. ARTICLE II UNION'S RESPONSIBILITY 1. The Plan provides (Article VI, Section 1) that during the existence of the Plan there shall be no
3 strikes, work stoppages, or picketing arising out of any jurisdictional dispute. 2. When a contractor has made a specific work assignment, all unions shall remain at work and process any complaint over a jurisdictional dispute in accordance with the procedures herein established by the Administrator. Any union which protests that a contractor has failed to assign work in accordance with the procedures specified above, shall remain at work and process the complaint through its International office. The Administrator is prohibited from taking action on protests or requests to discuss jurisdictional matters from local unions or building and construction trades councils. ARTICLE III STRIKES AND IMPEDIMENTS TO JOB PROGRESS 1. When it is alleged, in a written notice, by a stipulated employer directly affected by the dispute, the signatory Employer Association representing such employer or a stipulated National or International Union, that a work stoppage, slowdown, or other impediment to job progress is taking place, the Administrator shall proceed as set forth in Article VI of the Plan. 2. Notice to the Administrator shall include: a. Party engaged in strike, slowdown, or impediment to job progress [specify] b. Unions directly involved (in most cases, trade
4 receiving original assignment) c. Brief description of work in dispute d. Name of project and city and state where located e. Contractor and subcontractor, if any, directly involved, and mailing address, phone number and facsimile number of each f. A statement detailing how the responsible contractor and involved Unions are stipulated to be bound to the Plan and these procedures. Required Format for Notice [Name of Union or Employer] is [state basis for claim of violation, e.g. strike] over a jurisdictional dispute between [Name of Unions] over [Briefly describe work and name of job] project, [City and state or, Province]. [Name of Contractor], [Mailing Address, Phone Number and Facsimile Number]. [Name of Subcontractor], [Mailing Address, Phone Number and Facsimile Number]. This contractor is stipulated to the Plan and these procedures by virtue of [provision in collective bargaining agreement or signed stipulation on file in Plan office*]. The Unions are stipulated to the Plan by virtue of [being an affiliate of the Department, a signed stipulation on file in the Plan office, or a provision in collective bargaining agreement]. * A sample stipulation form is contained on page 15 of the Procedural Rules and Regulations.
5 3. Impediments to job progress shall include, but not be limited to: a. Filing a grievance under a collective bargaining agreement, or under a local plan for the settlement of jurisdictional disputes not recognized by the Department, where an issue is a case, dispute or controversy involving a jurisdictional dispute or assignment of work by a stipulated contractor, or by a stipulated subcontractor. Provided, that it shall not be considered an impediment to job progress if the responsible contractor or Union is not stipulated to the Plan or a grievance is filed over the failure of the responsible contractor to conduct a pre-job or mark-up meeting when required to do so under the terms of the applicable collective bargaining agreement. b. Filing an unfair labor practice charge with the National Labor Relations Board, or appropriate Canadian equivalent, as determined by the Administrator, or action in any court against a stipulated employer or a stipulated National or International Union, or local affiliate thereof, where an issue is a case, dispute or controversy involving a jurisdictional dispute or assignment of work. Provided, that it shall not be considered an impediment to job progress if the responsible contractor is not stipulated to the Plan.
6 ARTICLE IV FILING A COMPLAINT 1. When a dispute over an assignment of work arises, the National or International Union challenging the assignment, or the employer directly affected by the jurisdictional dispute, or the signatory Employer Association representing such employer, shall notify the Administrator in writing. Such notice shall include the following information: a. Unions involved b. A full and complete description of the work in dispute c. Name and location of project d. Contractors involved and their mailing addresses, telephone number and facsimile number e. The assignment of work and the contractor who made the assignment f. A statement indicating whether the responsible contractor and the involved Unions are stipulated to the Plan and these procedures. g. A statement whether the representatives of the National and International Unions have met or attempted to meet at the local level in an effort to resolve the matter. h. A statement whether the National and International Unions involved in the dispute have voluntarily agreed to mediation. 2. The notice shall be in writing and sent to: For Projects in the United States
7 Administrator Plan for the Settlement of Jurisdictional Disputes in the Construction Industry Suite 1000 900 Seventh Street, NW Washington, DC 20001 Fax: (202) 775-1950 For Projects in Canada Administrator Plan for the Settlement of Jurisdictional Disputes in the Construction Industry c/o Office of the Executive Secretary Building and Construction Trades Department, AFL-CIO Suite 1902 130 Albert Street Ottawa, Ontario K1P 5G4 Fax: (613) 230-5138 ARTICLE V TIME CONSTRAINTS UNDER THE PLAN In computing any period of time prescribed in the Plan or the Procedural Rules and Regulations, the day from which the designated period of time begins to run shall not be included. The last day of the period so computed shall be included, unless it is a Saturday, a Sunday, or a legal holiday, in which event the period runs until the end of the next day which is not a Saturday, a Sunday, or a legal holiday.
8 When the period of time described or allowed is less than 7 days, intermediate Saturdays, Sundays, and legal holidays shall be excluded in the computation. As used herein, "legal holiday" in the United States includes New Year's Day, Presidents' Day, Memorial Day, Independence Day, Labor Day, Columbus Day, Veterans Day, Thanksgiving Day, Christmas Day, and any other Day designated as a holiday by the Administrator. "Legal holiday" in Canada includes New Year's Day, Victoria Day, Labour Day, Remembrance Day, Boxing Day, Good Friday, Canada Day (Dominion Day), Thanksgiving Day, Christmas Day, Civic Holiday, and any other day designated as a holiday by the Administrator. ARTICLE VI DIRECT RESOLUTION 1. Within two (2) days following receipt of a properly filed notice, the Administrator shall notify, by facsimile or other electronic means, all directly affected National and International Unions and employers that a dispute exists between local parties. 2. If any party intends to rely on a Decision of Record to support its claim to the work, that fact must be disclosed to the Administrator and the other parties to the dispute within two days of receipt of the notice of the dispute from the Administrator. The title of the Decision of Record and the page number where the decision is located should be included in the notice. If any other party to the dispute intends to challenge the Decision of Record on the basis of the prevailing practice in the
9 locality in the past ten years, pursuant to Article V, Section 8(b) of the Plan, notice of such challenge must be provided to the Administrator and to the other parties to the dispute by the day the list of arbitrators is due back in the Administrator’s office. 3. If the directly affected National and International Unions and employers, parties to the dispute, are able to settle the dispute, each shall inform the Administrator, in writing, signed by an authorized representative of each party, that a settlement has been reached. 4. If the directly affected National and International Unions and employers are unable to resolve the dispute, any of the directly affected parties may request arbitration of the dispute within five (5) days from the date the matter was referred by the Administrator, by filing a notice in writing to arbitrate with the Administrator, with copies to all directly affected parties. ARTICLE VII SELECTING AN ARBITRATOR 1. Upon receipt of a request to arbitrate, the Administrator shall send to all directly affected parties a list of impartial arbitrators, knowledgeable about the construction industry, chosen by the Joint Administrative Committee. 2. The directly affected National and International Unions and the responsible contractor(s) will each have three days in which to cross off the name of one arbitrator to which it objects, number the remaining names to indicate the order of preference and return the list to the Administrator. If a party does not return the list within the
10 time specified, all persons named therein shall be deemed acceptable. From among the persons who have been approved on each party's list, and in accordance with the designated order of mutual preference, the Administrator shall notify the parties of the arbitrator selected who is able to schedule a hearing within the time constraints set forth in the Plan. 3. If the parties are unable to select an arbitrator, the Administrator shall appoint an arbitrator. ARTICLE VIII RESOLUTION BY ARBITRATION 1. Upon his selection, the arbitrator, with the assistance of the Administrator, shall set and hold a hearing within seven (7) days. 2. The Administrator shall notify the responsible contractor(s) and the appropriate National and International Unions and signatory association(s) by facsimile or other electronic means of the place and time chosen for the hearing. Said hearing shall be held in Washington, D.C. or, for a dispute arising in Canada, in Eastern, Central or Western Canada as determined by the Administrator. 3. Attendance at arbitration hearings by the parties shall be limited to one full-time employee of each National or International Union party, or its affiliate, as designated by the President of each National or International Union, and one full-time employee of the responsible contractor party. On appeals from Local Boards, each party may also
11 have in attendance the individual who presented that party's case to the Local Board. Failure to attend by a party shall not delay a hearing, the taking of evidence, or the issuance of a decision. 4. Presentations shall be in writing with copies for each party, the arbitrator, and a file copy. 5. The arbitrator shall issue his decision within three (3) days after the case has been closed. The decision of the arbitrator shall be final and binding on all parties to the dispute. 6. Each party to the arbitration shall bear its own expenses for the arbitration and agrees that the fees and expenses of the arbitrator shall be borne by the losing party or parties as determined by the arbitrator if all parties are stipulated to the Plan, otherwise as determined by the arbitrator. 7. Following the issuance of the decision, the Administrator will send a statement to the party or parties responsible for payment of the arbitrator's fees and expenses. Such statement shall be payable within ten (10) days of receipt. If payment is not received within 30 days, a late fee of $500 will be assessed on the delinquent party. A future request by a delinquent party to process a case will be held by the Administrator until all outstanding fees and expenses, including any late fee, have been paid. ARTICLE IX POLICY REGARDING DIRECTIVES 1. The Plan and the Procedural Rules and Regulations provide for the settlement of a
12 jurisdictional dispute on a specific job by agreement or understanding between or among the National and International Unions involved. 2. The Procedural Rules and Regulations also provide that an assignment of work may be changed by the responsible contractor(s) to conform to the terms of same, upon notification by the Administrator. Such notification shall be made by means of a directive sent to the responsible contractor(s) by the Administrator. 3. In order to give effect to the procedure set forth above, and before a directive may be sent to the affected contractor(s) by the Administrator, the National or International Unions involved shall submit for the records of the Plan the following: a. A statement of the exact terms of the agreement or understanding reached. Such statement is to be jointly signed by authorized representatives of each of the National or International Unions involved. If separate communications are submitted by the parties, the terms of the agreement or understanding must be identical in each communication. b. A statement regarding the notification to the responsible contractor(s) of the agreement or understanding reached. If objection to the agreement or understanding was made by the contractor(s) or representatives, the nature of the objection must be stated. 4. In accordance with the Plan and the Procedural Rules and Regulations, any directive
13 from the Administrator shall be complied with by the affected contractor(s) unless, and within 24 hours following receipt of such directive, the contractor(s) notifies the Administrator that he elects not to comply with the directive, and requests that the jurisdictional dispute be processed through arbitration to a decision. Such decision shall be made in accordance with the provisions of Article V of the Plan. ARTICLE X APPEALS FROM DECISIONS OF RECOGNIZED LOCAL BOARDS 1. Appeals from local settlements, agreements, or decisions issued by a plan for the settlement of jurisdictional disputes that has been recognized by the Department, may be filed with the Administrator within seven (7) days of issuance by the National or International Unions directly affected, or by the responsible contractor(s), or a signatory Employers Association representing such employer. a. Such filing shall include a copy of the local settlement, agreement, or decision being appealed and the specific basis for the appeal. Simultaneous notice shall be given all other parties. 2. The authority of the Administrator to refer an appeal to arbitration is discretionary. The Administrator shall, in exercising his authority, consider whether the parties were afforded an opportunity to present evidence at a hearing conducted for that purpose under the Plan and in conformity with generally recognized procedures not
14 incompatible with the provisions and procedures of this Plan and whether the decision of the Local Board addresses the established criteria of Article V, Section 8, of the Plan. 3. Appeals referred to arbitration will be processed in accordance with Article V of the Plan. 4. Presentations shall be in writing and limited to that which was presented at the recognized local plan for the settlement of jurisdictional disputes.
15 STIPULATION In signing this stipulation, the undersigned [employer] [employer association on behalf of its members] [union] agrees to be bound by all the terms and provisions of the Agreement establishing procedures for the resolution of jurisdictional disputes in the construction industry known as the Plan for the Settlement of Jurisdictional Disputes in the Construction Industry. In particular, the undersigned agrees to abide by those provisions of the Plan requiring compliance with the decisions and awards of the Administrator, arbitrators or National Arbitration Panels established under the Plan, and to fulfill the obligations set forth in the Agreement. This stipulation shall run for the term of the Agreement and shall continue in effect for each year thereafter unless specifically terminated effective upon the anniversary date of said Agreement, in accordance with the notice provisions contained in the Agreement. The effective date of this stipulation shall be the date it is received in the Plan Administrator’s office. (Signed) ............................................................................ Company ......................................................................... Date ................................................................................. To facilitate expeditious processing of jurisdictional disputes, all parties are encouraged to file signed Stipulation forms with the Administrator.
16 PLAN FOR THE SETTLEMENT OF JURISDICTIONAL DISPUTES IN THE CONSTRUCTION INDUSTRY PREAMBLE This Agreement is entered into by and among the Building and Construction Trades Department, AFL-CIO, on behalf of its constituent National and International Unions and their affiliated local unions (referred to hereinafter as the Department) and the Employer Associations signatory to this Agreement (referred to hereinafter as the Employer Associations). The parties to this Agreement dedicate their efforts to improving the construction industry by providing machinery for the handling of disputes over work assignments without strikes or work stoppages thus stabilizing employment in the industry at the same time increasing both its efficiency and capacity to furnish construction services to the public at reasonable cost. ARTICLE I SCOPE OF APPLICATION The procedures shall be available to resolve jurisdictional disputes between and among Employers and Unions engaged in the building and construction industry.
17 ARTICLE II STIPULATION REQUIREMENTS Sec. 1. In order to process Impediment to Job Progress disputes pursuant to Article III of the Procedural Rules and Regulations and Article VI of the Plan, all parties to the dispute must be stipulated to the Plan. (a) A Union may become stipulated to the Plan by virtue of its affiliation with the Department or its National or International Union’s affiliation with the Department, a signed a stipulation form setting forth that it is willing to be bound by the terms of the Plan or a provision in a collective bargaining agreement. (b) An Employer may become stipulated to the Plan by virtue of its membership in a stipulated association of employers with authority to bind its members, a signed stipulation form setting forth that it is willing to be bound by the terms of the Plan or a provision in a collective bargaining agreement. Sec. 2. Stipulation shall not be required in order to process jurisdictional disputes pursuant to Article V, requests for determination of changes of original assignment pursuant to Article I of the Procedural Rules and Regulations and requests for the issuance of directives pursuant to Article IX of the Procedural Rules and Regulations, except that the moving party must be stipulated to the Plan.
18 ARTICLE III JOINT ADMINISTRATIVE COMMITTEE Sec. 1. There shall be established a Joint Administrative Committee (hereinafter referred to as the "JAC"), to oversee the operation of the Plan. See. 2. The JAC representing the Department and the signatory Employer Associations shall consist of eight (8) voting members, four (4) nominees from the Department and four (4) from the Employer Associations. There shall be a Chairman and a Vice-Chairman of the JAC. The Chairman shall be the President of the Department. The Vice-Chairman shall be designated by the signatory Employer Associations. The Chairman and the Vice-Chairman shall be non-voting members of the Committee. Sec. 3. The JAC shall appoint two Administrators of the Plan. One Administrator shall handle all matters arising in the United States. The second Administrator shall handle all matters arising in Canada. References to the Administrator in this Agreement and the Procedural Rules and Regulations shall mean the appropriate U.S. or Canadian Administrator. The Administrators shall be compensated at a rate and under terms to be established by the JAC. Sec. 4. The Administrator shall be responsible for disbursement of the funds, shall keep the books of the Plan and submit to the parties to the Agreement a quarterly financial statement; shall provide for an annual audit of the books by a certified public
19 accountant and shall prepare annually a proposed budget of the necessary expenses of the Plan for the following twelve (12) months and submit same to the JAC for approval. The total amount of the budget, when approved, shall be subscribed annually in advance, 50 percent by the Department and 50 percent by the signatory Employer Associations. All expenditures shall be within the approved budget. In order to assure adequate funding of the Plan, the JAC, may establish a schedule of fees to be charged to parties wishing to utilize the services of the Plan but who are not affiliated with one of the organizations signatory to this Agreement. ARTICLE IV RULES AND REGULATIONS Sec. 1. The Administrator shall adapt his operations to assure that all cases submitted shall be disposed of as expeditiously as possible. Sec. 2. The Administrator, with the prior approval of the JAC, shall establish such procedural regulations and administrative practices as may be required for the effective administration of this Agreement, provided such regulations and practices are consistent with the expressed terms of this Agreement. Sec. 3. The JAC shall have the power to revise the procedural regulations and administrative practices of the Administrator. The Administrator shall promptly notify all parties to the Plan of any revisions in the procedural or administrative practices.
20 Sec. 4. The Administrator shall keep records of disputes and decisions and develop such statistical and operational information as may be of value to the JAC. The Administrator shall from time to time make recommendations to the JAC for changes in the Procedural Rules and Regulations or provisions of the Plan which will strengthen and improve the effectiveness of the Plan. Sec. 5. It shall be the duty of the Administrator to process cases of jurisdictional disputes in the Building and Construction Industry when disputes are referred to him by any of the National and International Unions involved in the dispute, or an Employer directly affected by the dispute on the work in which he is engaged or by the signatory Employer Association representing such Employer. Sec. 6. If any party is not stipulated to the Plan, any of the National or International Unions involved in a dispute may file a statement with the Plan Administrator indicating that, if all parties had been stipulated to the Plan, the Union would have filed a jurisdictional dispute pursuant to Article V of the Plan. The notice shall include the unions involved, a description of the work in dispute, the name and location of the project, the name of the responsible contractor, the assignment that was made by the contractor and which of the Article V, Section 8, criteria the Union contends supports its claim to the work. The Plan Administrator shall compile a list of such statements and distribute it to the parties to the Plan monthly.
21 Sec. 7. In the interest of expediting resolutions of jurisdictional disputes, the Administrator shall undertake to keep a record of decisions involving the same type of dispute and involving the same trades and report such record quarterly to the JAC. ARTICLE V RESOLUTION OF JURISDICTIONAL DISPUTES Sec. 1. When a dispute over an assignment of work arises, the National or International Union challenging the assignment, or the Employer directly affected by the dispute or the signatory Employer Association representing such Employer shall notify the Administrator in writing, with copies to the other parties to the dispute. The notice shall include a statement whether representatives of the National and International Unions have met or attempted to meet with the local parties to attempt to resolve the matter. For disputes in the United States, if the National and International Unions involved in the dispute voluntarily agree to mediation, the notice shall so advise the Administrator. The mediation may be used in lieu of the meeting of the International Representatives. Sec. 2. Upon receipt of said notice, the Administrator or his designee shall notify within two (2) days by facsimile or other electronic means all directly affected National and International Unions and employers that a dispute exists between the local parties. The Administrator shall also provide notice of the dispute to all other National
22 and International Unions party to this Agreement. At the same time, if the National and International Unions involved in a dispute in the United States have consented to voluntary mediation, the Administrator shall contact the Federal Mediation and Conciliation Service and request the appointment of a mediator to assist the parties in the local area in settling the dispute. The mediator shall have three (3) days from the date the matter is referred by the Administrator to mediate the dispute. The mediator shall submit by facsimile or other electronic means a report to the parties and the Administrator indicating whether the dispute has been resolved no later than the end of the three (3) day period. The report of the mediator shall not be submitted to a Plan Arbitrator. Sec. 3. If the respective National and International Unions of the disputing locals and the directly affected Employer are unable to resolve the dispute, any of the directly affected parties may request arbitration of the dispute, within five (5) days, from the date the matter is referred by the Administrator, by filing a notice to arbitrate with the Administrator, with copies to all directly affected parties. The Administrator will only honor a request to submit the matter to arbitration prior to the expiration of the five (5) day period if the requesting party has demonstrated that the International Representatives have met or attempted to meet with the local parties to resolve the matter or have been through the mediation process set forth in Section 2. Sec. 4. Upon receipt of said notice, the Administrator shall send to all directly affected parties a list of impartial arbitrators knowledgeable
23 about the construction industry, chosen by the JAC. Sec. 5. The directly affected National and International Unions and the responsible contractor(s) will each have three days in which to cross off the name of one arbitrator to which it objects, number the remaining names to indicate the order of preference and return the list to the Administrator. If a party does not return the list within the time specified, all persons named therein shall be deemed acceptable. From among the persons who have been approved on each party's list, and in accordance with the designated order of mutual preference, the Administrator shall notify the parties of the arbitrator selected. If the parties are unable to select an arbitrator, the Administrator shall appoint the arbitrator. Sec. 6. Upon his selection the Arbitrator, with the assistance of the Administrator, shall set and hold a hearing within seven (7) days. The Administrator shall notify the employer and the appropriate National and International Unions and Employer Associations by facsimile or other electronic means of the place and time chosen for the hearing. Said hearing shall be held in Washington, D.C. or, for a dispute arising in Canada, in Eastern, Central or Western Canada as determined by the Administrator. A failure of any party or parties to attend said hearing without good cause, as determined by the Administrator, shall not delay the hearing of evidence or issuance of a decision by the Arbitrator. Sec. 7. The Arbitrator shall issue his decision within three (3) days after the case has been closed. The
24 decision of the Arbitrator shall be final and binding on all parties to the dispute. Sec. 8. In rendering his decision, the Arbitrator shall determine: (a) First whether a previous agreement of record or applicable agreement, including a disclaimer agreement, between the National or International Unions to the dispute governs; (b) Only if the Arbitrator finds that the dispute is not covered by an appropriate or applicable agreement of record or agreement between the crafts to the dispute, he shall then consider the established trade practice in the industry and prevailing practice in the locality. Where there is a previous decision of record governing the case, the Arbitrator shall give equal weight to such decision of record, unless the prevailing practice in the locality in the past ten years favors one craft. In that case, the Arbitrator shall base his decision on the prevailing practice in the locality. Except, that if the Arbitrator finds that a craft has improperly obtained the prevailing practice in the locality through raiding, the undercutting of wages or by the use of vertical agreements, the Arbitrator shall rely on the decision of record and established trade practice in the industry rather than the prevailing practice in the locality; and (c) Only if none of the above criteria is found to exist, the Arbitrator shall then consider that because efficiency, cost or continuity and good management are essential to the well being of the industry, the interests of the consumer or the past practices of the employer shall not be ignored.
25 The Arbitrator shall set forth the basis for his decision and shall explain his findings regarding the applicability of the above criteria. If lower-ranked criteria are relied upon, the Arbitrator shall explain why the higher-ranked criteria were not deemed applicable. The Arbitrator's decision shall only apply to the job in dispute. Sec. 9. Agreements of record are applicable only to the parties signatory to such agreements. Decisions of record are applicable to all trades except as provided for in the Decision of Record. Sec. 10. The Arbitrator is not authorized to award back pay or any other damages for a misassignment of work. Nor may any party to this Plan bring an independent action for back pay or any other damages, based upon a decision of an Arbitrator, except that a party may seek back pay or damages for the period of non-compliance with an Arbitrator’s decision from any party that fails to comply with such decision within seven business days of the issuance of the Arbitrator’s decision. Sec. 11. Each party to the arbitration shall bear its own expense for the arbitration and agrees that the fees and expenses of the Arbitrator shall be borne by the losing party or parties as determined by the arbitrator if all parties are stipulated to the Plan, otherwise as determined by the Arbitrator. An administrative fee, in accordance with the fee schedule established by the JAC, shall be paid to the Plan by any party that is not affiliated with one of the organizations signatory to this Agreement.
26 Sec. 12. Any party to a dispute that has been arbitrated that believes the Arbitrator failed to address the established criteria of Article V, Section 8, may request the JAC to consider an appeal. No appeal may be processed unless the Arbitrator's decision has been implemented. Sec. 13. A request to consider an appeal from a final decision of a Plan Arbitrator shall be filed with the Administrator, with copies to the other parties to the dispute, within five days of the date the Administrator transmitted the Arbitrator's decision. The request to consider an appeal shall include a copy of the Arbitrator's decision being appealed and a statement describing the basis of the claim that the Arbitrator failed to address the established criteria of Article V, Section 8. The other parties to the dispute shall have three days to submit to the Administrator, with copies to the other parties, a response to the request for appeal. Sec. 14. Once the submissions of the parties are complete, the Administrator shall distribute copies of the appeal to the members of the JAC that are not parties to the dispute. Within five days from receipt of the submissions, each member of the JAC shall notify the Administrator whether the appeal should be heard. If a majority of the JAC does not wish to consider the appeal, the decision of the Arbitrator shall be final and binding. If a majority of the JAC members believes the appeal has merit, the Administrator shall arrange for a meeting of the JAC, which may be by telephone conference, to consider the appeal. The sole issue to be considered on appeal is whether the Arbitrator failed to
27 address the established criteria of Article V, Section 8. Sec. 15. If the JAC determines that the Arbitrator failed to address the established criteria of Article V, Section 8, it shall remand the case to the Administrator to process for a hearing before a new Plan Arbitrator. ARTICLE VI CONTINUATION OF WORK Sec. 1. During the existence of this Agreement, there shall be no strikes, work stoppages or picketing arising out of any jurisdictional dispute. Contractors and subcontractors shall make work assignments in accordance with Article I of the Procedural Rules and Regulations. Members of National and International Unions and their Local affiliates stipulated to the Plan shall continue to work on the basis of their original assignment. Sec. 2. Recognizing that it is in the best interests of the parties to this Agreement, the Department, on behalf of itself and the General Presidents of each of the National and International Unions stipulated to the Plan reaffirm their desire to eliminate work stoppages, slowdowns and other impediments to job progress and their intent to comply with the provisions of the Plan prohibiting jurisdictional strikes and agree to enforce these provisions by direction and action of their respective National or International offices. In the event of a work stoppage, slowdown or other impediment to job progress, the employer or National or International Union may take the following course
28 of action: (a) The employer or National or International Union shall notify the Administrator or his designee of the alleged breach of this Article. Notice to the Administrator shall be by the most expeditious means available, with simultaneous notice by facsimile or other electronic means to the party alleged to be in violation and the involved employer and National or International Union President(s). The employer will immediately use its best efforts to cease any violation of this article. The International President(s) will immediately instruct, order and use the best efforts of his office to cause the local union or unions to cease any violation of this article. A National or International Union complying with this obligation shall not be liable for unauthorized acts of its local union. (b) Upon receipt of said notice, the Administrator or his designee shall select an arbitrator from a panel of arbitrators chosen by the JAC. (c) Upon his selection, the Arbitrator shall hold a hearing within 24 hours if it is contended that the violation still exists. (d) The Arbitrator, with the assistance of the Administrator, shall notify the employer, the local union(s) and the appropriate National or International Union(s) and Employer Association(s) by facsimile or other electronic means of the place and time he has chosen for this hearing. Said hearing shall be held in Washington, D.C. or, for a dispute arising in Canada, in Eastern, Central or Western Canada as determined by the Administrator, and shall be
29 completed in one session. A failure of any party or parties to attend said hearing shall not delay the hearing of evidence or issuance of a decision by the Arbitrator. (e) The sole issue at the hearing shall be whether or not a violation of this Article has in fact occurred, and the Arbitrator shall have no authority to consider any matter in justification, explanation or mitigation of such violation or to award damages. The Arbitrator's decision shall be issued in writing within 3 hours after the close of the hearing, and may be issued without an opinion. If any party desires an opinion, one shall be issued within 15 days, but its issuance shall not delay compliance with, or enforcement of, the decision. The Arbitrator may order cessation of the violation of this Article and other appropriate relief, and such decision shall be served on all parties by facsimile or other electronic means upon issuance. (f) Each party to the arbitration shall bear its own expense for the arbitration and agrees that the fees and expenses of the Arbitrator shall be borne by the losing party or parties as determined by the arbitrator. ARTICLE VII ENFORCEMENT Sec. 1. When the JAC has determined that an Employer or National or International Union is in violation of this Agreement, such Employer or National or International Union shall be denied a representative on any committee established by this Agreement and shall also be denied the right to process a case during the period
30 of violation. Sec. 2. Any decision or interpretation rendered by an arbitrator shall be immediately accepted and complied with by all parties subject to this Agreement. If a party fails to accept and comply with a decision or interpretation rendered by an arbitrator or a ruling of the Administrator or the JAC, any party to the dispute may seek court enforcement of the decision or ruling. (a) At the election of the party seeking enforcement, an Arbitrator’s decision or a ruling of the Administrator or the JAC may be enforced in the United States District Court for the District of Columbia or any other court which has jurisdiction of the parties. All parties signatory or stipulated to this agreement consent to the jurisdiction of the United States District Court for the District of Columbia. For a dispute arising in Canada, an Arbitrator’s decision or a ruling of the Administrator or the JAC may be enforced in the appropriate Canadian court. (b) Any rights created by statute or law governing arbitration proceedings which are inconsistent with this Agreement or which interfere with compliance therewith are hereby waived by the parties to whom they accrue. (c) A party seeking enforcement of an Arbitrator’s decision or ruling of the Administrator or JAC due to the failure of another party to abide by the decision or ruling shall be reimbursed by the party failing to abide by the decision or ruling for any attorneys’ fees, court costs and expenses incurred, in addition to any back
31 pay or damages sought pursuant to Article V, Section 10. ARTICLE VIII LOCAL BOARDS Sec. 1. In any community or locality where a plan for the settlement of jurisdictional disputes has been recognized by the Department, it shall be used in the first instance to bring about an agreement, settlement or decision. However, any such local settlement, agreement or decision may be appealed by any of the involved parties in accordance with Section 2 and 3 of this Article. Sec. 2. The Administrator is empowered to refer to arbitration, in accordance with Article V, Sections 5-10, any appeal from a decision or ruling of a Local Board recognized under Section 1. The authority of the Administrator to refer a case to arbitration shall be discretionary. The Administrator is authorized, subject to the prior approval of the JAC, to prescribe rules as to the types of cases he will refer to arbitration. Sec. 3. The Administrator shall have the authority to establish such procedural regulations and administrative practices as may be required for the effective administration of this appeals procedure, subject to the prior approval of the JAC.
32 ARTICLE IX OBLIGATIONS OF THE PARTIES Sec. 1. Each Employer agrees that all cases, disputes or controversies involving jurisdictional disputes or assignments of work arising under this Agreement shall be resolved as provided herein, and shall comply with the decisions and rulings of the Administrator, the JAC, arbitrators or National Arbitration Panels established hereunder. Sec. 2. Each Union agrees that all cases, disputes or controversies involving jurisdictional disputes or assignments of work arising under this Agreement shall be resolved as provided herein, and shall comply with the decisions and rulings of the Administrator, the JAC, arbitrators or National Arbitration Panels established hereunder. Each Union agrees that the establishment of picket lines and/or the stoppage of work by reason of an Employer’s assignment of work are prohibited. Sec. 3. The Administrator shall send a monthly report to the parties to this Agreement setting forth all information on jurisdictional disputes for that month. The report should include the location and job where the dispute occurred, the parties involved, the subject of the dispute and shall indicate whether any stoppage occurred or picket lines were established.
33 ARTICLE X NATIONAL ARBITRATION PANEL Sec. 1. National Arbitration Panels shall be established hereunder and shall be composed of three arbitrators, knowledgeable in the construction industry, appointed by the JAC. Sec. 2. (a) The JAC shall meet quarterly and among its other duties and responsibilities it shall, at each meeting, review the record of disputes filed with the Administrator and in particular shall review the record of decisions involving the same trades as submitted by the Administrator in accordance with Article IV, Section 6 hereof. (b) A dispute will be declared repetitive by the JAC when in its judgment such dispute is disruptive to the industry or seriously jeopardizes the operational integrity of the Plan. All parties to the Plan may bring a dispute to the JAC for such determination. The JAC will develop such criteria and guidelines to determine what constitutes a repetitive dispute. The JAC will issue a written report to the party or parties who have requested a decision from the JAC involving the dispute referred for such consideration. The written report will be timely and reflect the circumstances and criteria used by the JAC to determine whether or not said dispute is in fact considered repetitive. (c) In the event the JAC declares a dispute to be
34 repetitive, the JAC shall refer the matter to the National and International Unions involved for a period of not more than 90 days during which time the Unions shall consult with the Employer Associations who represent Employers who have responsibility for that type of work. The Unions shall endeavor to reach a national agreement governing future jurisdiction. The Administrator shall assist the Unions and may appoint a mediator to facilitate settlement. If an agreement is reached, it shall be attested to by the Administrator and shall serve as a criterion for decisions in future disputes. Should the National and International Unions fail to reach an agreement within 90 days, the Administrator shall refer the dispute to a National Arbitration Panel. Sec. 3. In any case to go to a National Arbitration Panel, the Administrator shall notify all General Presidents of National and International Unions affiliated with the Department and the signatory Employer Associations stating the controversy to be considered. Only directly affected parties as determined by the JAC shall be allowed to intervene. Thirty days notice shall be given of the date set for the hearing. Briefs shall be submitted and exchanged by all parties to the dispute at least ten days prior to the hearing date. Sec. 4. The National Arbitration Panel shall in every instance consider all pertinent evidence, including the criteria set forth in Article V, Section 8, and shall render a decision, if possible, within ten (10) days after the conclusion of the hearings. Copies of the National Arbitration Panel's decision shall be sent to
35 all parties signatory to this Agreement. Decisions of the National Arbitration Panel shall be immediately recognized under the provisions of the Constitution of the Department. Decisions of the National Arbitration Panel shall be immediately accepted and complied with by the disputing unions. Sec. 5. In the event any party to a dispute fails to present its case within the stated time, the National Arbitration Panel shall, nevertheless, proceed with the case and make its decision on the basis of the evidence presented. ARTICLE XI TECHNOLOGICAL CHANGES Sec. 1. The JAC shall establish a standing Technological Change Committee. The Committee shall concern itself with technological changes in the building and construction industry as they affect the jurisdiction of the various unions in the building and construction industry. The Committee shall consist of ten members from the Building and Construction Trades Department and ten members from the signatory Employer Associations, respectively. The Committee shall select a chairman and a secretary. Sec. 2. The Committee is authorized to establish subcommittees provided that there is equal representation of labor and management on each subcommittee. Each subcommittee shall elect a chairman and a secretary. Sec. 3. The Committee shall study existing
36 methods of construction and procedures as they relate to technological changes in the industry and make recommendations to the JAC. The Committee may refer particular items to the crafts concerned who may establish committees to determine craft jurisdiction and report their decisions to the Department and the signatory Employer Associations. Sec. 4. The Committee shall submit a report of its activities, including reports from any subcommittees, quarterly to the JAC. ARTICLE XII NATIONAL AGREEMENTS REGARDING JURISDICTION Sec. 1. When national agreements regarding jurisdiction between National or International Unions have been negotiated, immediate notice of such agreements shall be given to the appropriate management groups. Prior consultation with such groups regarding the making of agreements between National or International Unions is desirable and should be carried on. Sec. 2. National agreements entered into and properly signed by disputing National or International Unions shall be filed with the Administrator and attested by the Administrator. Such national agreements shall take effect prospectively and shall not apply to jobs in process at the time of execution. "Jobs in process" means any construction contract upon which the date for
37 submission of bids or proposals has passed. ARTICLE XIII EFFECTIVE DATE, TERMINATION, CHANGE AND WITHDRAWAL Sec. 1. This Agreement shall take effect on January 1, 2009, and shall remain in force and effect until December 31, 2009, and shall continue in effect for each year thereafter unless terminated as provided for herein. Changes or amendments to this Agreement may be made as provided for herein. Sec. 2. If either the Department or any signatory Employer Association desires to change or terminate this Agreement it shall notify the other party in writing at least ninety (90) days before the anniversary date of this agreement. When notice for change is given, the nature of the changes desired must be specified in the notice. This Agreement shall be subject to change at any time by mutual consent of the parties hereto. Any changes agreed upon shall be reduced to writing and signed by the parties hereto, the same as this Agreement. IN WITNESS WHEREOF the parties have caused this Agreement to be executed and effective as of the day and year above written.
38 FOR THE BUILDING AND CONSTRUCTION TRADES DEPARTMENT, AFL-CIO MARK H. AYERS President FOR THE EMPLOYER ASSOCIATIONS North American Contractors Association IZ CAKRANE National Electrical Contractors Association JOHN M. GRAU Mechanical Contractors Association of America, Inc. JOHN McNERNEY The Association of Union Constructors STEPHEN R. LINDAUER Sheet Metal and Air Conditioning Contractors National Association DEBORAH WYANDT
39JURISDICTIONAL AGREEMENTS ENTEREDINTO BETWEEN AFFILIATED INTERNATIONALUNIONS AND DECISIONS RENDERED AFFECT-ING THE BUILDING INDUSTRY THAT AREHELD TO BE OPERATIVE BY THE BUILDINGAND CONSTRUCTION TRADES DEPARTMENTBy theAmerican Federation of Labor, Building andConstruction Trades Department, A. F. of L.,National Board for Jurisdictional AwardsCarpenters and PaintersFor the purpose of bringing about conditions of har-mony and co-operation, the following agreement hasthis day been entered into and agreed to by and betweenthe Brotherhood of Painters, Decorators and Paperhang-ers of America and the United Brotherhood of Carpen-ters and Joiners of America:(1) It is agreed that the members of the United Broth-erhood of Carpenters and Joiners of America shall erectand install all work in connection with and required for,acoustical purposes up to the point of applying canvas,muslin or similar materials to take the finished decora-tions, which work shall be done by the members of theBrotherhood of Painters, Decorators and Paperhangersof America.(2) The applying and erection of all mouldings, in con-nection with acoustical work, shall be done by membersof the United Brotherhood of Carpenters and Joiners ofAmerica.
40(3) If any misunderstanding arises as to the meaningor carrying out of any of the provisions containedherein, the same shall be taken up with the General Pres-idents of the two organizations parties hereto.(4) This agreement to be in force and effect when ap-proved by the Executive Board of the two organizationssignatory hereto.For the United Brotherhood of Carpenters and Joinersof America:GEO. H. LAKEYJ.W. WILLIAMSW.T. ALLENFor the Brotherhood of Painters, Decorators and Paper-hangers of America:JOS. F. KELLEYCHARLES A. CULLENCLARENCE E. SWICKDated December 17, 1928.Witness:WM. J. MCSORLEYPresident, Building Trades DepartmentLathers and Sheet Metal WorkersAgreement between the Wood, Wire and Metal Lath-ers’ International Union and the Sheet Metal Workers’International Association to govern the installation ofproducts manufactured by the Knapp Brothers’ Manu-facturing Company of Chicago, Ill., and similar prod-ucts.In order to simplify any differences that may arise onbuilding operations, it is agreed by both parties to this
41agreement that the following products are conceded bythe Wood, Wire and Metal Lathers’ International Unionas the work of the members of the Sheet Metal Workers’International Association:Sanitary Metal Cove Base, No. 202.Sanitary Metal Cove Base, No. 203.Sanitary Metal Cove Base, No. 204.Sanitary Metal Cove Base, No. 205.Sanitary Metal Cove Base, No. 501.Sanitary Metal Window Stool and Frame, No. 302.Sanitary Metal Window Stool, No. 304.Sanitary Metal Chalk Trough, No. 303.It is conceded by the Sheet Metal Workers’ Interna-tional Association that the following products are thework of the members of the Wood, Window and MetalLathers’ International Union:Knapp Metal Base Grounds and Screeds, style Nos.1, 1¹⁄₂, 2, 42, 49.Knapp Metal Casing Beads, Nos. 39 and 41.Eclipse Metal Picture Mould, No. 23.“Royal” Metal Picture Mould, No. 20.Knapp Sanitary Metal Chair Rail, No. 300.Metal Bull Nose Beads and Metal Corner Beads ofevery description.Inside and Outside Corner Fittings.This agreement made and entered into January 12,1926.WOOD, WIRE AND METAL LATHERS’ INTERNATIONALUNION.JOHN H. BELL, Gen. Pres.WM. J. MCSORLEY, 1st Gen. Vice Pres.A. D. YODER, Gen. Sec.-Treas.
42SHEETMETAL WORKERS’ INTERNATIONAL ASSOCIA-TION.JOHN J. HYNES, Gen. Pres.WM. L. SULLIVAN, Gen. Sec.-Treas.ROBERT BYRON, Int. Rep.EXPLANATIONSanitary Metal Cove Base, No. 202:Used at intersections of floors and walls or parti-tions and comes 4 in. and 6 in. high. This base iserected before plastering and is so set as to form aground screed for plastering and for the finished ce-ment floor.Sanitary Metal Cove Base, No. 203:Used at intersections of floors and walls or parti-tions and comes in widths of 4 in. and 6 in. This is aflush base placed after floors and plastering is com-pleted.Sanitary Metal Cove Base, No. 204:Is similar to No. 203 except that it comes in two sec-tions where No. 203 comes in but one section.Sanitary Metal Cove Base, No. 205:Is similar to No. 204 except that the base is put inplace before plastering and the top portion of itforms a ground for plastering. It comes 4 in. and 6in. wide.Sanitary Metal Cove Base, No. 501:Is similar to No. 202 with the exception of very littlechange in its form.
43Sanitary Metal Window Stool and Frame, Nos. 302 and304:Is a metal jamb running from 4 in. to 6 in. in widthand a return on wall which forms a plaster ground.Sanitary Metal Chalk Trough, No. 303:As its name implies, is a chalk trough to go underblackboards in schoolhouses and is placed afterplastering is completed.It will hardly be necessary for me to explain that por-tion of the work which the Sheet Metal Workers concedeto come under our jurisdiction, as you must be familiarwith the names of the different materials mentioned inthe agreement.Painters and PlasterersNew York, N.Y., February 16, 1928.This agreement entered into by and between the Oper-ative Plasterers and Cement Finishers’ International As-sociation and the Brotherhood of Painters, Decoratorsand Paperhangers of America, in the matter of jurisdic-tion to govern the application of California Stucco“CRAFTEX,” “TEXTONE” and other materials of likecharacter, shall be as follows:This agreement shall become effective February 16,1928, that the applying of all California Stucco shall bethe work of the Plasterers’ organization. That the finish-ing of the same it is agreed that the Plasterers shall bepermitted to apply one wash and thereafter all washingand the applying of colors shall be under the jurisdictionof the Brotherhood of Painters.
44It is hereby agreed that all “CRAFTEX,” “TEXTONE”or other material of the same character, when appliedover a scratch or brown coat of plaster, shall be thework of the Plasterer, said material to be applied with atrowel, or other usual methods of plastering.It is hereby agreed that all “CRAFTEX,” ‘TEXTONE”or other material of like character, when applied over asand finish or white coat of plaster, shall be the work ofthe Painter, said material to be applied with a brush, orother usual method of painting.It is agreed that when the material in question is ap-plied to show windows for decorative purposes, anddoes not exceed 150 yards in all, it shall be the work ofthe Painter, and when the work exceeds 150 yards andapplied over a scratch or brown coat of plaster, it shallbe the work of the Plasterer.For Plasterers:EDW. J. MCGIVERNT. A. SCULLYFor Painters:JOS. F. KELLEY, 2d G.V.P.CHAS. A. CULLEN, 3d G.V.P.Attest:WM. J. MCSORLEY,Pres., Building Trades Department.
45Carpenters and LathersAgreement entered into between the representativesof the United Brotherhood of Carpenters and Joinersand Wood, Wire and Metal Lathers’ International Union,January 14, 1903.Pending the action of their convention, the UnitedBrotherhood of Carpenters and Joiners of America agreenot to assert jurisdiction over any iron work includingiron or wire lathing, studding, or any other exclusivelyiron work claimed by the Wood, Wire and Metal Lathers’International Union.The Wood, Wire and Metal Lathers’ International Unionagree that we will not assert jurisdiction over or allowour members to perform any wood work, including shin-gling, wooden arches, door or window frames, woodenstudding or furring, or any other carpenter or woodwork, except wooden lath to receive plastic material.Signed for the United Brotherhood of Carpenters andJoiners of America:WM. D. HUBER, President.FRANK DUFFY, General Secretary.Signed for the Wood, Wire and Metal Lathers’ Interna-tional Union:CHAS. LANGLANDS,JOHN STEVENS, Committee.Carpenters and LathersAugust 21, 1928.RELATIVE TO JURISDICTION OVER MATERIAL KNOWNASCELOTEX
46Further taking up the question of jurisdiction over thematerial know as “CELOTEX,” and in accordance withthe tentative proposals on this subject between our or-ganizations, we, the undersigned, hereby agree that thematerial known as Celotex Lath comes under the juris-diction of the Lathers’ International Union; all otherCelotex material comes under the jurisdiction of theUnited Brotherhood of Carpenters and Joiners.UNITED BROTHERHOOD OF CARPENTERS AND JOIN-ERS OF AMERICA.WM. L. HUTCHESON, Gen. Pres.FRANK DUFFY, Gen. Sec.WOOD, WIRE AND METAL LATHERS’ INTERNATIONALUNION.JOHN H. BELL, Gen. Pres.A. D. YODER, Sec.-Treas.Boiler Makers and Iron WorkersApproved May 28, 1926It is agreed that the following work shall be recog-nized as coming under the jurisdiction of the Interna-tional Brotherhood of Boiler Makers, Iron Ship Buildersand Helpers of America:SECTION 1. The construction, erection and assemblingof all boilers, parts and work in connection therewith,including boiler fronts, heat units, water walls, tubesupports and casings (except the unloading, hoisting, orlowering and placing of complete boilers, steam drumsand assembled sections of water tube boilers to theirapproximate positions), all connections between theboiler and stack (commonly known as breeching), built
47of sheet steel or iron, supports for the same (which arenot part of the building structure), uptakes, smokeboxes, air and water heaters, smoke consumers, hot orcold air ducts (except when used for ventilating pur-poses).SEC. 2. Iron and steel ship building.SEC . 3. Pontoons, purifying boxes, gas generators andwash tanks or scrubbers, standpipes, brewery vats (ex-cept glass enameled tanks), water tower (except struc-tural frames and balconies), all iron and steel pipe line,penstock and flume work, steam, air, gas, oil, water, orother liquid tanks or containers requiring tight joint, in-cluding tanks of riveted, caulked or welded constructionin connection with swimming pools.SEC . 4. The following work in and around blast fur-naces and rolling mills, viz.: hot stoves, blast furnaces,cupolas and dump cars, and all steam, air, water, gas, oilor other liquid tight work (all other iron and steel workin such buildings shall be done by Iron Workers).SEC . 5. Gasometers, including all frame work in con-nection with same.SEC . 6. All iron or steel stacks, in connection withpower plants, furnaces, rolling mills, manufacturingplants, and all other power plants (except small powerplants in connection with hotels or office buildings andsectional or other steel stacks erected in office buildingsor hotels), and all extensions or repairs of such stacksshall be done by Boiler Makers.It is agreed that the following work shall be recog-nized as coming under the jurisdiction of the Interna-tional Association of Bridge, Structural and OrnamentalIron Workers:
48SECTION1. The erection and construction of all iron,steel and ornamental iron entering into the erectionand construction of the following: Buildings, bridges,viaducts, subways and tunnels, towers, hoists, cardumpers, cranes, coal conveyors, ore unloaders, stok-ers, supports for boilers, coal bins and hoppers, ashchutes and hoppers, rock, coke, sand and ore bins andhoppers, kilns, driers, coolers, crushers, mixers, pul-verizers, roasters, all caisson work, safe deposit boxes,vaults, vestibules and doors, glass enameled tanks,malt drums, fans, and hot rooms and ventilators includ-ing air ducts in connection therewith, all swimmingpools (except as specified in Section 3 of the BoilerMakers’ classification of work in this agreement) andthe wrecking of all of the above work shall be done byIron Workers.SEC . 2. The erection and construction of all sectionaland other steel or iron stacks, erected in office buildingsand hotels; and all stacks erected in small power plantsin connection with hotels and office buildings, and theextension and repair to such stacks shall be the work ofthe Iron Workers.SEC . 3. The erection and construction of structuraliron work and balconies in connection with water tow-ers shall be the work of the Iron Workers.SEC . 4. The erection and construction of all steel andiron work around rolling mills and blast furnaces (ex-cept that specified in Section 4 of the Boiler Makers’classification of work) shall be done by Iron Workers.SEC . 5. The unloading, hoisting or lowering and plac-ing of complete boilers, steam drums, and assembledsections of water tube boilers to their approximate posi-tions shall be done by Iron Workers.
49SEC. 6. The burning and welding on work awarded tothe Boiler Makers shall be done by Boiler Makers, andthe burning and welding on work awarded to the IronWorkers shall be done by Iron Workers.SEC . 7. Any further disputes that may arise betweenthe parties of this agreement shall be first considered bythe respective General Presidents. Upon their failure toagree, the question shall be submitted to arbitration.None of the work definitely decided upon in this agree-ment shall be subject to further arbitration.For the International Brotherhood of Boiler Makers,Iron Ship Builders and Helpers of America:(Signed) J.A. FRANKLIN.WM. ATKINSON.JOS. P. RYAN.MARTIN DALEY.For the International Association of Bridge, Structuraland Ornamental Iron Workers:(Signed) P. J. MORRIN.W. J. MCCAIN.DAN J. O’SHEA.MICHAEL C. ARTERY.Sheet Metal Workers and Boiler MakersMr. John J. Hynes, General President642 Transportation BuildingWashington, D.C.Dear Sir and Brother:The International Brotherhood of Boiler Makers, IronShip Builders and Helpers of America, through the un-
50dersigned duly authorized officers, hereby officially rec-ognize and acknowledge the established jurisdictionalrights of the members of the Sheet Metal Workers’ Inter-national Association to manufacture, assemble, erectand install all sheet metal work of No. 10 gauge or lighterwhen used in connection with the construction, equip-ment, alteration and repair of buildings.In witness thereof we hereby affix our hand and sealthis 16th day of October, 1930.For the International Brotherhood of Boiler Makers,Iron Ship Builders and Helpers of America:(Signed) J. A. FRANKLIN,International President.For the Sheet Metal Workers’ International Association:(Signed) JOHN J. HYNES,General President.Iron Workers and Elevator ConstructorsJune 9, 1931.The undersigned representatives of the InternationalAssociation of Bridge, Structural and Ornamental IronWorkers, and the International Union of Elevator Con-structors, Operators and Starters mutually agree thatboth organizations shall co-operate with and supporteach other to maintain Union conditions and their mem-bers upon the work of their respective trades, and thatfor the purpose of establishing complete harmony be-tween both organizations, this agreement is hereby en-tered into, effective on and from this date.
51All semi or full automatic elevator doors or gates, andall operating devices shall be the work of the ElevatorConstructors.All elevator doors or gates manually operated, includ-ing all elevator enclosures, front, facias, sills, frames andbucks, shall be the work of the Iron Workers.Steel trusses, girders and supports for escalators,where riveted or welded, shall be the work of the IronWorkers.All other escalator work shall be the work of the Ele-vator Constructors.All theater curtains, back-stage lifts, and equipment inconnection therewith, shall be assembled and erected bythe Iron Workers, excepting the operating machinery.Orchestra and Console lifts shall be assembled anderected by the Elevator Constructors, including the ma-chinery in connection therewith, and all machinery inconnection with theater curtains and back-stage lifts.(The above two paragraphs shall also apply to audito-riums, schools, convention halls, and other buildingssimilarly equipped.)All of the above is hereby agreed to and accepted bythe signatories to this agreement for their respective or-ganizations.For the International Association of Bridge, Structuraland Ornamental Iron Workers:(Signed) P. J. MORRIN,General President.
52WM. H. POPE,5th Gen. Vice-Pres.JOHN M. SCHILLING,7th Gen. Vice-Pres.W. J. MCCAIN,General SecretaryFor the International Union of Elevator Constructors,Operators and Starters:(Signed) FRANK FEENEY,International PresidentJ. C. MACDONALD,1st Int. Vice-Pres.WALTER SNOW,2nd Int. Vice-Pres.JOSEPH F. M URPHY,Int. Sec.-Treas.International Union of Operating Engineers andUnited Association of JourneymenPlumbers and Steam FittersAGREEMENTIn the controversy between the United Association ofPlumbers and Steam Fitters and the International Unionof Steam and Operating Engineers in Cleveland, Ohio,over an air compressor that was used by the Plumbersfor boring holes in a concrete floor, and which was re-ferred by the local unions of Cleveland and the Interna-tional representatives of both organizations to the Inter-national Presidents of the United Association ofPlumbers and Steam Fitters and the International Union
53of Steam and Operating Engineers for adjustment, wefind that at the A. F. of L. Convention held in Norfolk, Va.,in 1907, Resolution No. 124, which was presented by theInternational Union of Steam and Operating Engineersand adopted by the Convention, gives jurisdiction overthis work to the International Union of Steam and Oper-ating Engineers.We also find in the jurisdiction claims filed by the In-ternational Union of Steam and Operating Engineerswith the Building Trades Department upon their en-trance into the Department, that this work is covered intheir jurisdiction by the following paragraph:“HOISTING AND PORTABLE”“All hoisting and portable engines on building andconstruction work, where operated by steam, electricity,gasoline, hydraulic or compressed air, including pumps,siphons, pulsometers, concrete mixers, air compressorsand elevators, where used for hoisting building material,street rollers, steam shovels, dinky locomotives, cable-way, clam shells and pile drivers.”Both International Presidents met in Washington onJanuary 5, 1925, at the headquarters of the BuildingTrades Department, and upon finding the action of the A.F. of L. Convention upon Resolution No. 124 and the ju-risdiction filed with the Building Trades Department thatthis work of operating air compressors belongs to theHoisting and Portable Engineers, it is agreed that thelocal unions will be notified to that effect.(Signed) JOHN COEFIELD,(Signed) ARTHUR M. HUDDELL.
54Sheet Metal Workers’ International Associationand United Association of JourneymenPlumbers and Steam FittersAGREEMENTINDIANAPOLIS, IND.January 28, 1928.Report of the Committees appointed by the United As-sociation of Journeymen Plumbers and Steam Fittersand the Sheet Metal Workers’ International Association,to take up the matter of sheet lead in building construc-tion.This Committee met at Hotel Severin, Indianapolis,Ind., Friday, January 27, 1928, with the following repre-sentatives in attendance: Wm. Lynn, George Mastertonand Bert Stephenson, representing the United Associa-tion of Plumbers and Steam Fitters, and James Lennon,Richard Pattison and James T. Moriarity, representingthe Sheet Metal Workers International Association.The Committee organized with Wm. Lynn, Chairman;James T. Moriarty, Secretary. The Committee was visitedby Robert Fox, Local Agent of the Plumbers, and CharlesWilson, Local Agent of the Sheet Metal Workers. Afterhearing both agents, the Committee went into executivesession and after holding several meetings, reached thefollowing agreement:“Sheet lead work used in roofing, gutters, valleys,flashings in connection with roofing and ducts in di-rect connection with ventilation systems shall be thework of the Sheet Metal Workers, members of theSheet Metal Workers’ International Association. Allother sheet lead work including roof flashings in con-
55nection with plumbing, shall be the work of thePlumbers, members of the United Association of Jour-neymen Plumbers and Steam Fitters.”We, the undersigned committee, recommend that thisagreement shall go into effect when approved andsigned by the International Presidents of the above or-ganizations.(Signed) WM. LYNN,(Signed) GEORGE MASTERTON,(Signed) BERT STEPHENSON,Representing United Association of JourneymenPlumbers and Steam Fitters,(Signed) JOHN COEFIELD,General President,(Signed) JAMES LENNON,(Signed) R. PATTISON,(Signed) JAMES T. MORIARTY,Representing Sheet Metal Workers’ InternationalAssociation,(Signed) JOHN J. HYNES,General President.Bricklayers, Masons and Plasterers’ InternationalUnion and Operative Plasterers and CementFinishers’ International AssociationAgreement entered into between the B.M. & P.I.U. ofAmerica and the O.P.&C.F.I.A. at the Headquarters ofFirst-Named Organization, Odd Fellows Bldg., Indi-anapolis, Ind.FEBRUARY 17, 1911.
56First. The O.P.&C.F.I.A. agrees to a mutual interchangeof cards with the B.M.&P.I.U., same to cover all citieswhere the O.P.&C.F.I.A. have locals and the B.M.&P.I.U.has mixed locals, and that the following stipulations berecognized.Second. The support to be given in the interest of ei-ther organization in the localities where the B.M.&P.I.U.controls shall be determined by the Executive Boards ofboth organizations in conference when the necessity forsuch support arises. No work to be performed until theconference board comes to a decision.Third. The B.M.&P.I.U. recognizes and concedes thesole right of the O.P.&C.F.I.A. to organize and charterunions composed of exclusive plasterers in all localitieswhere a sufficient number of bona fide resident plaster-ers can be secured, and guarantees that no interferenceon their part shall take place, except under conditionshereafter stated, and that no exclusive plasterers’ unionshall be chartered by the B.M.&P.I.U. under any circum-stance.Fourth. The conditions existing under which an exclu-sive union of plasterers is permitted to be organized interritory already controlled by the B.M.&P.I.U. havingbeen a matter of complaint at the conference, the repre-sentatives of the B.M.&P.I.U. have determined that thegrounds upon which the complaint is based are justifiedand that same demand a concession upon their part—i.e.,that of permitting the bricklayers and stonemasons of amixed union the right to cast a vote upon the question ofthe plasterer members being allowed to form a separateunion. Said representatives agree to eliminate the brick-layer and stonemason when such votes are being taken inthe future, and that only the recognized plasterer mem-bers of the union shall be allowed to cast a vote upon
57such propositions. That in all cases where two-thirds ofsuch plasterer members vote in favor of separation, theGeneral Secretaries of the O.P.&C.F.I.A. and theB.M.&P.I.U. shall be notified of same by the secretary ofthe union, and a charter shall be immediately granted.Fifth. The B.M.&P.I.U. agrees that the subcontractingof the plastering contract of a bona fide employer or gen-eral contracting firm shall not be objected to by any ofits subordinate unions upon all general contracts ex-ceeding $50,000, pending the convening of the next bien-nial convention of the B.M.&P.I.U. at which conventionlegislation will be asked for that will make permanentthe relief ordered at this time.Sixth. That the O.P.&C.F.I.A. charters be withdrawnfrom Springfield, Newark, and Rochester, and the mem-bers of each respective union be admitted to member-ship in the B.M.&P.I.U. local free of any penalty or initia-tion fee. All fines placed upon O.P.&C.F.I.A. memberscovering their actions in the above-named three citiesare also hereby removed.Seventh. In any city under a mixed charter of theB.M.&P.I.U. where there are but three or less plasterersaffiliated, and there are five or more plasterers who arebona fide residents who are not members, theO.P.&C.F.I.A. is conceded the right to organize a union,and all B.M.&P.I.U. members following plastering shallbecome members of the newly chartered exclusive(O.P.&C.F.I.A.) Plasterers’ Union free of initiation fee.“OFFENSIVE AND DEFENSIVE ALLIANCE”Eighth. That in all movements, “offensive or defen-sive,” no subordinate local of either International Unionshall be permitted to take any action whatsoever until
58the question requiring joint action shall have first beenacted upon and determined by the Presidents of theO.P.&C.F.I.A. and the B.M.&P.I.U.Ninth. No movement of an “offensive” or “defensive”character shall be countenanced in cases where suchwould be in violation of any existing agreements.RULES GOVERNING INTERCHANGEABLE CARDSThe rules governing the issuing of the Interchangeabletraveling card and the clearance card shall be subject tothe rules agreed upon at the conference of October 30,1906, and as revised at the conference of February 13,1909.In Witness Whereof, We, the undersigned, hereby setour hand and seal this eighteenth day of February, 1911.For the O.P.&C.F.I.A:JOHN DONLIN, President.EDW. J. MCGIVERN, 1st Vice-Pres.(Seal)PETER G. COOK, 3rd Vice-Pres.W. A. O’KEEFE, Organizer.For the B.M.&P.I.U. of America:WM. J. BOWEN, President.THOS. R. PREECE, 1st Vice-Pres.WM. DOBSON, Secretary.ACOUSTONEAt a meeting of the Joint Conference between the Ex-ecutive Boards of the Bricklayers, Masons and Plaster-ers’ International Union of America and the OperativePlasterers and Cement Finishers’ International Associa-
59tion of the United States and Canada held in Atlantic City,February 27, 1930, it was agreed, that the above-namedmaterial and those of a similar character shall be in-stalled on a fifty-fifty basis equally divided between themembership of the Operative Plasterers and Cement Fin-ishers’ International Association of the United States andCanada and the Bricklayers, Masons and Plasterers’ In-ternational Union of America irrespective of thickness.ARTIFICIAL STONEIn order to reach an amicable understanding betweenthe B.M.&P.I.U. and the O.P.&C.F.I.A. regarding the in-stallation of the artificial stone or marble, theO.P.&C.F.I.A. concedes to the membership of theB.M.&P.I.U. the installation of artificial stone or marblewhen same are precast and of 3/4 of an inch or more inthickness. And the B.M.&P.I.U. concedes to theO.P.&C.F.I.A. that installation of said imitation stone ormarble when same are less than 3/4 of an inch in thick-ness, also said artificial stone when same are applied tochannel iron furring. It is also understood that eachparty hereto will confine their method of erection or ap-plication to the Craft method of erection or applicationemployed heretofore and that the 3/4 inch thickness re-ferred to heretofore is 3/4 inch in the body of piece notinclusive of any relief members or enrichments appear-ing on the surface.TilelayersOwing to the fact that the Tilelayers organization hasignored agreements held between themselves and theO.P.&C.F.I.A.; also the B.M.&P.I.U., the agreements werereported abrogated. The B.M.&P.I.U. assuming control ofthe tilelaying business.
60AGREEMENT(PREPARATION OFWALLS AND CEILINGSTORECEIVE TILE)Agreement entered into this 22nd day of August, 1917,between the B.M.&P.I.U. and the O.P.&C.F.I.A. pertainingto the preparing or plastering of walls and ceilings whichare to receive tile; First. It is agreed that the Plasterers of theO.P.&C.F.I.A. and the B.M.&P.I.U. shall prepare or plasterall walls which are to receive tile. They shall plumb, rodand square all walls and scratch the same so as to guar-antee adhesion of the final coat which shall be put on bythe Tilelayer to act as a bed for his tile.Second. It is further agreed that the Plasterers of ei-ther the O.P.&C.F.I.A. of the B.M.&P.I.U. shall prepare orplaster all ceilings which are to receive tile. All ceilingsmust be leveled and rodded and properly scratched so asto guarantee adhesiveness of the final coat which shallbe applied by the Tile Setter and act as a bed for his tile.Third. It is further agreed that the Plasterers shall useonly sand and cement in the preparation of work abovestipulated unless otherwise specified by the architect.Fourth. Any member of either organization that vio-lates the above rules shall, upon conviction, be fined thesum of $25.00.“Resolved, to qualify the agreement entered into be-tween the Interstate Mantel and Tile Contractors’ Asso-ciation, Operative Plasterers and Cement Finishers’ In-ternational Union and the Bricklayers, Masons and Plas-terers’ International Union of America to read:“That three bathrooms, vestibules and small halls inprivate residents shall be plastered by the tile setter.”
61AGREEMENTAgreement entered into this day of ,1918, by and between the Interstate Mantel and Tile Con-tractors’ Association, the Operative Plasterers and Ce-ment Finishers’ Association of the United States andCanada, and the Bricklayers, Masons and Plasterers’ In-ternational Union of America.“The purpose of this agreement is to prevent hereafterjurisdictional disputes that have existed for the pasttwenty years between the tile and plastering interests,and which have resulted in many strikes among theworkmen involved to the detriment of employer and em-ployee and the building public.“First. It is agreed that all materials for plasteringwork entering into the preparation of all walls, ceilings,etc., to receive tile and other work, and conceded ascoming under the jurisdiction of the Mantel and TileContractors’ Association, shall be included in the esti-mate and contract and the work shall come under the ju-risdiction of the Mantel and Tile Contractors.“Second. It is agreed that the plasterers of theO.P.&C.F.I.A. and the B.M.&P.I.U. shall prepare or plasterall walls and ceilings which are to receive tile, except thefinal setting bed, which shall be applied by the tilelayer.“Third. All preparation work shall be done in a thor-ough and workmanlike manner, and it is understood andagreed that all walls and ceilings shall be plumbed, lev-eled and rodded under the direct supervision of the tilelayers.(Signed) ED. J. MCGIVERN,President O.P.& C. F. I.A.
62PETERG. COOK,Vice-President O.P.& C. F. I.A.T. A. SCULLY,Secretary O.P.& C. F. I.A.W. A. O’KEEFE, General Organizer O.P.& C. F. I.A.WM. J. BOWEN,President B.M.&P.I.U.THOS R. PREECE, Vice-President B.M.&P.I.U.WM. DOBSON,Secretary B.M.&P.I.U.Carpenters and Sheet Metal WorkersAGREEMENTFor the purpose of bringing about conditions of har-mony and co-operation the following agreement is thisday entered into and agreed to by and between the SheetMetal Workers’ International Association and the UnitedBrotherhood of Carpenters and Joiners of America:It is agreed that members of the United Brotherhoodof Carpenters and Joiners of America shall erect and in-stall all interior metal trim such as bucks, jambs, doors,casings, base, chair-rail, picture mouldings, partitions,and all other material generally referred to as trim ex-cept toilet partitions, which shall be done by Sheet MetalWorkers. Also, when a sheet metal contractor who is en-gaged in manufacturing and erecting sheet metal prod-ucts for buildings, such as cornices, sky-lights, metalroofing, ventilating work, etc., manufactures the mate-rial referred to as trim, with members of the Sheet MetalWorkers’ International Association they shall do the
63erecting of same in a manner that will comply with theworking agreement now in force between the SheetMetal Workers and said firms.It is further agreed that in the setting of metal windowframes that when frames are set, stayed, plumbed orbraced such work shall be done by Carpenters, but if setor placed in an opening in walls left when a building iserected the work shall be done by Sheet Metal Workers.The hanging and adjusting of metal sash shall be done bySheet Metal Workers. It is further agreed that any metalwork in connection with store fronts shall be done bySheet Metal Workers.It is further understood and agreed that in the erectionof metal column forms the erection shall be done bySheet Metal Workers. Any framing in connection there-with shall be done by Carpenters.It is further agreed that the installation of metal lock-ers, also the erection of ordinary plain metal shelvingshall be done by Sheet Metal Workers.It is further understood and agreed that the membersof neither organization shall work on any building wherenon-union men of the other craft are employed.If any misunderstanding arises as to the meaning orcarrying out of any of the provisions contained hereinthe matter will be taken up with the General Presidentsof the two organizations.Dated March 21, 1928.For United Brotherhood of Carpenters and Joiners:WM. L. HUTCHESON,FRANK DUFFY,T. M. GUERIN.
64For Sheet Metal Workers’ International Assn.:JOHN J. HYNES, R. PATTISON,ROBT. BYRON, W. J. ROONEY,JAMES T. MORIARTY, THOMAS FAY.In the last part of paragraph Two of the Agreement en-tered into this 21st day of March, 1928, by and betweenthe Sheet Metal Workers’ International Association andthe United Brotherhood of Carpenters and Joiners ofAmerica, beginning with “Also,” it is understood andagreed that this refers only to the firms now manufactur-ing hollow metal doors and trim in their own shops inthe City of Chicago, and the erecting of same in accor-dance with the working agreement between the SheetMetal Workers and said firms, now in force.WM. L. HUTCHESON JOHN J. HYNESSheet Metal Workers-Asbestos WorkersAgreementAgreement entered into this 13th day of April, 1939, byand between the Sheet Metal Worker’s International As-sociation and the International Association of Heat andFrost Insulators and Asbestos Workers covering the ap-plication of insulation and acoustical materials on insideand outside of sheet metal ducts and fittings in connec-tion with ventilation and air-conditioning systems.1. All insulating material applied on outside of sheetmetal ducts and fittings is recognized as coming withinthe jurisdiction of the International Association of Heatand Frost Insulators and Asbestos Workers.2. All acoustical materials applied inside of sheetmetal ducts and fittings, in shop or on job prior to erec-tion of said ducts and fittings by Sheet Metal Workers, is
65recognized as coming within the jurisdiction of the SheetMetal Workers’ International Association.3. All acoustical materials applied inside of sheetmetal ducts and fittings on job after said ducts and fit-tings have been erected by Sheet Metal Workers is recog-nized as coming within the jurisdiction of the Interna-tional Association of Heat and Frost Insulators and As-bestos Workers.4. Any dispute or controversy arising out of the appli-cation or interpretation of this agreement shall be re-ferred to and settled immediately by the General Presi-dents of the two International Unions involved, in accor-dance with the purpose and intent of this agreement.(Signed)FOR SHEET METAL WORKERS’ INTERNATIONAL ASSOCIATION,ROBT. BYRON, General President.JAMES T. MORIARTY.WM. O’BRIEN, General Secretary-Treasurer.INTERNATIONAL ASSOCIATION OF HEAT AND FROST INSULA-TORS AND ASBESTOS WORKERS.JOSEPH A. MULLANEY, General President.C. W. SICKLES, General Secretary-Treasurer.Between the United Association of JourneymenPlumbers and Steamfitters and the UnitedBrotherhood of Carpenters and Joiners ofAmericaBATH AND TOILET ROOM ACCESSORIES ANDMEDICINE CABINETSIt is agreed that the installation of all bath and toiletroom accessories, such as paper holders, towel rails or
66bars, glass holders, glass shelves, etc., however installed,shall be the work of the members of the United Associa-tion of Journeymen Plumbers and Steamfitters.Further, that the installation of bath and toilet roommedicine cabinets shall be the work of the members ofthe United Brotherhood of Carpenters and Joiners ofAmerica.UNITED ASSOCIATION OF JOURNEYMENPLUMBERS AND STEAMFITTERS.GEORGE MASTERTON.JOHN COEFIELD.UNITED BROTHERHOOD OF CARPENTERSANDJOINERS OF AMERICA.M.A. HUTCHESON.WM. L. HUTCHESON.Dated at Cincinnati, Ohio, September 29, 1939
67AGREEMENTAgreement between the United Brotherhood ofCarpenters and Joiners of America and theOperative Plasterers’ and Cement Finishers’International Association of the United Statesand Canada, at the headquarters of the FirstNamed Organization, Carpenters’ Building,Indianapolis, Ind., June 13, 1944.This Agreement entered into by and between theUnited Brotherhood of Carpenters and Joiners ofAmerica, the Operative Plasterers’ and CementFinishers’ International Association of the United Statesand Canada, in the matter of jurisdiction to govern thefabrication and setting of screeds and forms used inconnection with the placing and finishing of cement orconcrete, shall be as follows:1. The setting of screeds of lumber, metal or othermaterials to determine the proper grade of concretewhen used to serve as forms, such as 2" by 4"s, or otherplain pieces of material, when held in place by stakesand/or spreaders shall be done by Cement Finishers,members of the O.P.&C.F.I.A. and B.M.&P.I.U.A screed is a strip of wood or metal used as a guide forleveling or grading a concrete floor, slab or sidewalk.2. The fabricating of all screeds and stakes, for anypurpose, and the construction and setting of all formsshall be done by Carpenters, members of the U.B. of C. &J. of A.A form is a built-up section of wood, metal orcomposition board used for the purpose of mouldingconcrete to a given line or shape.
683. Any bulkhead that is one single board in height, andthat has no key attached or which is not notched orfitted shall be set and braced or staked by CementFinishers, providing same is used as a screed. The termbulkhead shall mean a form or screed erected for thepurpose of separating pours of concrete. Any bulkheadthat must be notched or fitted, or which has a keyattached or which is over one board high, or anybulkhead that is not used as a screed, shall be fabricatedand set by Carpenters.For the U.B. of C. & J. of A.:M. A. HUTCHESON, First General Vice President.JOHN R. STEVENSON, Second General Vice President.For the O.P. & C. F. I. A.:JOHN E. ROONEY, General President.JOHN J. HAUCK, First Vice President.
69MEMORANDUM OF UNDERSTANDINGBy and Between The International Brotherhood of ElectricalWorkersandThe International Hod Carriers’, Building andCommon Laborers’ Union of America*1. The International Brotherhood of Electrical Work-ers recognizes the jurisdiction of the International HodCarriers’, Building and Common Laborers’ Union ofAmerica over such work as all digging, excavating, grad-ing, backfilling, cutting and replacing of all pavementsand the handling of all material in connection therewith,performed for Gas Utility Companies, affiliated or non-affiliated with the Electric Utilities, in all cases exceptwhere the International Brotherhood of Electrical Work-ers has agreements now in effect as of this date. Suchagreement shall continue until the next termination pe-riod effective in said agreements and the InternationalBrotherhood of Electrical Workers agrees to exercise alloptions to change said agreements to conform with thedescription of jurisdiction as above outlined by servingsuch notice as may be required to effect such change. If,however, the International Brotherhood of ElectricalWorkers, at such period or periods of termination is con-vinced that the termination of any such agreementswould impair the prestige of the Electrical Workers inthe Electric Public Utility field, the matter of terminationof said agreements will be taken up and discussed by*For full report see page 133 of the Proceedings of the 34th An-nual Convention, New Orleans, 1940.
70both parties to this memorandum of understanding withthe protection of the mutual welfare and interest of bothparties to this memorandum of understanding being theparamount and deciding factor. When such terminationor changes are effected, the work shall revert to and beconsidered the work of the Laborers, parties hereto.2. It is recognized by both parties hereto that all provi-sions with respect to the work herein defined will applyin the instances of work in connection with water andsteam, in the same manner and to the same effect as ap-plies to gas. Likewise, the provisions relative to agree-ments now in effect apply on steam and water equallywith gas.3. The International Brotherhood of Electrical Work-ers reserves its established jurisdiction over right of wayclearance performed be members of the InternationalBrotherhood of Electrical Workers employed directly byElectric Utilities.4. The International Brotherhood of Electrical Work-ers recognizes that the work of right of way clearance,with the exception of the digging of post holes and an-chors and the back-filling of same, performed on or inconnection with transmission line construction, throughcontracts, or on R. E. A. projects, is the jurisdiction ofthe International Hod Carriers’, Building and CommonLaborers’ Union of America.5. The International Hod Carriers’, Building and Com-mon Laborers’ Union of America recognizes the jurisdic-tion of the International Brotherhood of Electrical Work-ers over handling of all electrical material, beginningwith the unloading at the first point of delivery on thejob, and continuing through its ultimate use or disposal.
716. Both parties to this understanding and agreementagree that there shall be no compacts entered betweeneither party and any third parties in a jurisdictional issueaffecting or involving either party hereto.7. Both parties hereto agree that in the instance of anyissues arising on work not herein covered or outlined,the settlement and disposal of such issues shall be onlythrough procedures before proper tribunals, establishedwithin the American Federation of Labor, or throughmethods agreed upon by the International Presidents ofthe organizations parties hereto.The International Brotherhood of Electrical Workersand the International Hod Carriers’ Building and Com-mon Laborers’ Union of America hereby affix the signa-tures of the respective International Presidents in ac-knowledgement of an agreement to terms of understand-ing herein described, this third day of February, 1940, atMiami, Fla.(Signed) D. W. Tracy,General President, International Brotherhoodof Electrical Workers.(Signed) Jos. V. Moreschi,General President, International Hod Carriers’,Building and Common Laborers’ Union of America.ARTICLES OF AGREEMENTBetween the United Association of JourneymenPlumbers and Steamfitters of the United Statesand Canada, Hereinafter Referred to as theUnited Association, and the International
72Brotherhood of Boiler Makers, Iron ShipBuilders, Welders and Helpers of America,Hereinafter Referred to as Boiler Makers.For the purposes of eliminating jurisdictional disputesbetween the membership of these two InternationalUnions, and for the further purpose of laying the ground-work for extensive cooperation and fraternal good willbetween the two memberships, and for the additionalpurpose of cooperating together in the unionization ofthose industries and firms in which we are jointly inter-ested, the representatives of the two InternationalUnions hereby undertake to dispose of the questions ex-isting between them which have provoked jurisdictionaldisputes. In so doing it should be understood by all con-cerned that we are attempting only to settle controver-sies between ourselves and are not undertaking to settledisputes which either of the organizations herein in-volved may have with other International Unions, or todispose of work which properly belongs to any other In-ternational Union.Refinery Installation1. On the equipment that has caused considerable mis-understanding in the industry, the United Association ofJourneymen Plumbers and Steamfitters and the Interna-tional Brotherhood of Boiler Makers, Iron Ship Builders,Welders and Helpers of America have agreed on the fol-lowing division of work, viz.:2. The installation of tubes in pipe stills or furnaces,commonly called oil heaters, will be handled, installedand finished by a composite crew equal in number ofBoiler Makers and members of the United Association.
733. The erection of furnace frame, casing, doors andsupport will be performed by Boiler Makers.4. All circulating piping, pipe hangers and oil burnerswill be installed by the United Association.5. The installing or removing of cooler, condenser andheat exchanger tube, or tubes of the shell and tube typeof equipment, by any mode or method, shall be the workof the Boiler Maker.6. The building of cooler, condenser and heat ex-changer pipe coils, by any mode or method, shall be thework of the United Association.7. The handling and setting of all work in connectionwith bubble or fractionating towers, reaction chambersor evaporators, trays, cups, baffles, tube sheets, tubes orother interior equipment shall be the work of the BoilerMaker.The United Association shall perform all internal andexternal piping, valves, strainers and floats.8. The application or installation of braces and sup-ports, riveted to pressure vessel, is the work of theBoiler Maker.9. The handling and placing of washers and agitators,including baffles, is the work of the Boiler Maker.10. Cooling tower pans, frames and condenser boxesis the work of the Boiler Maker.Coils and all pipe work in connection with same is thework of the United Association.11. All work in connection with coke stills and asphaltstills is the work of the Boiler Maker.
74All pipe work in connection with the same is the workof the United Association.12. The handling and settling of completed heat ex-changers is the work of the United Association.Pipelines13. It is hereby recognized that all transportation oiland gas lines is the work of the United Association.14. Plate fabricated aqueducts or water lines to thepoint where it enters city or town distributing system,whether riveted or welded, is the work of the BoilerMaker.Where flange or other patent joints are used it is thework of the United Association.15. Plate fabricated intake and discharge lines inpower plants, where riveted or welded joints are used, iswork of the Boiler Maker.Where flange or other patent joints are used it is thework of the United Association.16. All other classes of manufactured pipe—regardlessof material—used in the pipefitting industry, is the workof the United Association.Tanks17. Completed tanks which are an integral part of apiping job shall be installed by members of the UnitedAssociation.Knockdown or completed tanks which are not an inte-gral part of a United Association installation, for exam-
75ple, brewery vats, distillery vats, etc., in or on buildings,shall be the work of the Boiler Maker.18. All tankage for the storage of petroleum productsin the petroleum industry, including bulk storage plantsand all water towers, standpipes or water storage reser-voirs, shall be the work of the Boiler Maker.All pipe work in connection with same is recognizedas the work of the United Association.19. The erection and repair of gas holders is recog-nized as the work of the Boiler Maker.All pipe work in connection with same is recognizedas the work of the United Association.Boilers20. Hot and cold air and gas ducts in connection withboilers, furnaces or other duct work incidental to BoilerMakers’ installation is the work of the Boiler Maker.21. It is hereby recognized that the building of boilers,including economizers, superheaters, air heaters, cas-ings, burner boxes, down comers, sludge boxes andsluice troughs, completed marine bent tube boilers,breechings, stacks and all air and gas ducts in connec-tion with same is the work of the Boiler Maker.Soot blowers, fuel piping, valves, boiler trimmings, thesetting of completed boilers and knockdown cast iron-boilers and all pipe work in connection with same is thework of the United Association.22. The burning and welding on work in the jurisdic-tion of the United Association will be performed by themembers of the United Association.
76Burning and welding on work in the jurisdiction of theBoiler Maker shall be performed by the Boiler Maker.23. The handling and rigging of all materials and equip-ment coming under the jurisdiction of these two tradeswill be performed by each respective trade.24. It is understood that each class of work listedabove, under the several sub-heads, stands alone by it-self and no combination of sub-sections can be used toproduce a result not contemplated by this agreement, asthis agreement is fairly and honestly entered into andmust be so applied.25. Questions may arise which are not specifically cov-ered by the articles of this agreement and it is understoodthat our respective officers and representatives willmake a sincere effort to reach an amicable understandingbased upon the broad principles herein laid down.26. All new questions which may arise and which arenot clearly covered by the terms of this agreement andthat have failed of settlement locally between represen-tatives of the two Organizations shall be jointly submit-ted to the two International Presidents or the officer act-ing in his place, with all supporting data and argument. If the International Presidents fail to agree, they maysubmit same to a neutral umpire, jointly selected by them.The work disposed of by this agreement shall not be sub-ject to further arbitration or interpretation by any tribunal.27. This agreement supersedes and voids all previousagreements between the United Association and the Inter-national Brotherhood, and likewise voids all decisions oncontroversies which occurred between the two Interna-tional Organizations or between their affiliated localunions, affecting the United Association and the Interna-
77tional Brotherhood, or by the American Federation ofLabor, or the Building and Construction Trades Depart-ment of the American Federation of Labor, or by any othertribunal prior to the effective date of this agreement.United Association of JourneymenPlumbers and Steamfitters of theUnited States and Canada:CHARLES N. RAULEO A. GREENMICHAEL F. G ARRETTInternational Brotherhood of BoilerMakers, Iron Ship Builders, Weldersand Helpers of America:CHAS. J. MACGOWANHARRY NICHOLASSigned at Chicago, Ill., this 1st day of August, 1941.Approved:GEORGE MASTERTON,General President.WM. E. WALTER.J. A. FRANKLIN,International President.By the action of the 35th Annual Convention of the Build-ing and Construction Trades Department the agreementmade by and between the United Association of Plumbersand Steam Fitters and the International Brotherhood ofBoiler Makers, Iron Ship Builders, Welders and Helpers ofAmerica was accepted, with the understanding that thisagreement incorporated in the permanent record of the De-partment would not interfere with or alter the jurisdictionof any other National or International Union affiliated withthe Building and Construction Trades Department.
78Addendum to AgreementRe: Clarification—Rule 21—Agreement—Interna-tional Brotherhood of Boiler Makers, Iron ShipBuilders, Welders and Helpers of America andUnited Association of Journeymen Plumbers andSteamfitters of the United States and Canada.Subsequent to the writing of the terms of the agree-ment there has been a question raised regarding the ju-risdiction or work in connection with attemporatorswhich was not included in Rule 21 of the above agree-ment. Hence, it is agreed by the above contracting par-ties that the word “attemporator” shall be included inRule 21, paragraph 1, after the word “superheaters.”It is further discovered that a further clarification ofRule 21, paragraph 2, should be made by inserting Rule21, paragraph 2, in the second line after the word “trim-mings” the following language: “All circulating piping forappurtenances and component parts of boiler.”The amended Rule 21 would then read as follows:“It is hereby recognized that the building of boilers, in-cluding economizers, superheaters, attemporators, airheaters, casings, burner boxes, downcomers, sludge boxesand sluice troughs, completed marine bent tube boilers,breechings, stacks, and all air and gas ducts in connectionwith the same is the work of the Boiler Maker.”“Soot blowers, fuel piping, valves, boiler trimmings, allcirculating piping for appurtenances and componentparts of the boiler, the setting of completed boilers andknockdown cast iron boilers and all pipe work in connec-tion with same is the work of the United Association.”The agreement of August 1, 1941, between the two In-ternational Organizations has reduced jurisdictional dis-
79putes between these two Organizations to a very mini-mum and this clarification is made in the hope that itmay entirely eliminate any further jurisdictional misun-derstandings.(Signed) JOHN J. MCCARTIN,Special Representative.United Association ofJourneymen Plumbers andSteamfitters.(Signed) J. A. FRANKLIN,International President.International Brotherhood ofBoiler Makers.March 20, 1942.AGREEMENTBetween the International Brotherhood ofTeamsters, Chauffeurs, Warehousemen andHelpers, and the International Brotherhood ofElectrical Workers*It is hereby agreed that the operators of vehicles deliv-ering electrical material come under the jurisdiction ofthe International Brotherhood of Teamsters, Chauffeurs,Warehousemen and Helpers.It is further agreed that the operators of vehicles usedfor electrical construction work, maintenance work orelectrical repair work—that is, when such vehicles are*For full report see Case 41 of Executive Council’s Annual Re-port, 1942.
80used for transporting man or men and/or material to andfrom job, and said vehicle remains at job site with manor men in the performance of electrical work, and theoperation of the vehicle is an integral part of the work—such operator comes under the jurisdiction of the Inter-national Brotherhood of Electrical Workers.It is understood and agreed that the equipment oper-ated by electrical workers shall only be the truck carry-ing the line and maintenance crews, tools, etc., to andfrom the job, or the emergency car from electrical con-tracting shops carrying only tools and repair equipmentfor emergency work. Operation of all delivery equipmentfor the delivery of materials of all character, such aspoles, pipes, transformers, cables and electrical appli-ances, such as refrigerators, radios, etc., shall be the ju-risdiction of the International Brotherhood of Team-sters, Chauffeurs, Warehousemen and Helpers.Signed this 11th day of February, 1942.International Brotherhood of Teamsters,Chauffeurs, Warehousemen and Helpers:JOHN M. GILLESPIE,General Secretary-Treasurer.DAVE BECK,Vice President.International Brotherhood of ElectricalWorkers:G. M. BUGNIAZET,International Secretary.CHARLES M. PAULSEN,Chairman, Executive Council.EDWARD J. BROWN,International President.
81Agreement (Pointing or Caulking AroundSteel Window Sash)Agreement entered into April 12, 1919, at Indianapolis,Ind., between the Executive Officers of the B.M.&P.I.Uand O.P.&C.F.I.A. as follows:“It was agreed that the pointing around steel sash onexclusive concrete shall be done by the members of theO.P.&C.F.I.A. The pointing of all steel sash where wholeor part is masonry shall be done by the members of theB.M.&P.I.U.”For the O.P.&C.F.I.A.EDWARD J. MCGIVERN, President.PETER G. COOK, First Vice-President.THOMAS A. SCULLY, Secretary-Treasurer.W. A. O’KEEFE, Organizer.For the B.M.&P.I.U.WILLIAM J. BOWEN, President.THOMAS R. PREECE, First Vice-President.WILLIAM M. DOBSON, Secretary.Agreement for Avoidance of Dispute BetweenUnited Slate, Tile and CompositionRoofers and Sheet Metal Workers’ InternationalAssociation(Endorsed by Seattle Convention, Building TradesDepartment, November, 1913)DECISION RENDERED, JULY 12, 1922In the matter of the subject referred to in the forego-ing title, it is the decision of the Board that the followingagreement be concurred in:
82Upon that portion of the report of the Executive Coun-cil under the above caption the committee reported asfollows:“The representatives of the Sheet Metal Workers andthe Slate, Tile and Composition Roofers appeared beforeyour committee and requested that they be given an op-portunity to reach an agreement. The request wasgranted and the following represents the agreementreached by the trades in interest:“This agreement made and entered into at AtlanticCity, N.J., July 25, 1913, by and between the Sheet MetalWorkers, party of the first part and the Slate, Tile andComposition Roofers, party of the second part, in pur-suance of correspondence and action thereon as foundon page 76 of the Report of the Proceedings of the SixthAnnual Convention of the Building Trades Department,whereby the party of the first part agrees to cause its af-filiated local unions and their members to respect andobserve the trade jurisdiction of the party of the secondpart as approved by the Building Trades Department ofthe American Federation of Labor, and refrain fromdoing any work granted to said party of the second partin the aforesaid jurisdiction in all towns and localities,where the party of the second part has a duly charteredlocal union.The party of the second part agrees to cause all itslocal unions and their members to observe and respectthe jurisdiction of the party of the first part as estab-lished and approved by the Building Trades Departmentof the American Federation of Labor.”
83MEMORANDUM OF UNDERSTANDINGBetween The Operative Plasterers’ and Cement Finishers’International AssociationThe Bricklayers, Masons and Plasterers’International Unionand The International Hod Carriers’ Building andCommon Laborers’ Union1. This memorandum of understanding shall onlycover the performance of work coming under the juris-diction of either the Cement Finishers or Laborers inconnection with the preparation, pouring, placing,spreading, rodding and finishing of cement or concreteon highways, roads, streets and airport runways.2. The mixing, handling, pouring, puddling, blocking,vibrating and spreading of all concrete shall be the workof the Laborers. The setting, leveling and lining of allslab steel forms on roads, highways and streets shall bethe work of the Laborers.3. All labor on center expansion machine, all expan-sion and contraction joints, center stripes and centersteel shall be the work of the Laborers.4. The handling of bull floats where bull float is usedfor strike off shall be the work of the Laborers.5. The tending to Cement Finishers, the handling anddistributing of all material on sidewalks, curbs and gut-ters is the work of the Laborers.6. The setting of all forms for sidewalks, curbs andgutters shall be the work of the Cement Finishers.
847. Straight edging, floating, trowelling, edging, rubbingand brushing shall be the work of the Cement Finishers.8. It is understood that this memorandum is enteredinto for the purpose of clarifying jurisdiction as outlinedabove and in the event of any dispute arising in connec-tion with the work as outlined above, the said disputeshall be referred to the General Presidents of the Interna-tional Unions parties hereto. In the event of any disputearising on any work not covered by this agreement suchas bridge, viaducts and underpasses, the said disputeshall be immediately referred to the General Presidentsof the International Unions involved, or to whomever thesaid General President may assign, for the purpose of at-tempting to adjust the said dispute amicably. During theperiod of time that these attempts are being made for ad-justment there shall be no stoppage of work on the job.Operative Plasterers’ and Cement Finishers’ Interna-tional Association:JOHN E. ROONEY,JOHN J. HAUCK.President First Vice PresidentBricklayers, Masons and Plasterers’ International Union:HARRY C. BATES, A. J. CLELAND.President.International Hod Carriers’ Building and Common La-borers’ Union of America:Jos. V. Moreschi, John W. Garvey.General President.July 19, 1948Attested: RICHARD J. GRAY,President, Building and ConstructionTrades Department, AFL.
85AGREEMENT UNDER NATIONAL JOINT BOARDFOR SETTLEMENT OF JURISDICTIONALDISPUTES, BUILDING AND CONSTRUCTIONINDUSTRYWe the undersigned request that Joint Board No. 1 bedischarged. “The issue in dispute is the laying of woodfibre conduit underground for the carrying of electricalwires and cables.”It is agreed that this work is the work of the Interna-tional Brotherhood of Electrical Workers.Signed this 13th day of July, 1948.International Hod Carriers’ Buildingand Common Laborers’ Union ofAmerica: JOS. V. MORESCHI,General President.International Brotherhood of ElectricalWorkers: D. W. TRACY,International President.Attested: RICHARD J. GRAY,President of the Building and ConstructionTrades Dept., A.F. of L.Iron Workers—Elevator ConstructorsDirectional ElevatorsAGREEMENTMay 26, 1953For the purpose of establishing complete harmonyand cooperation on the erection of two directional eleva-tors for the Bowser Engineering Company in variousparts of the country, the International Association of
86Bridge, Structural and Ornamental Iron Workers, and theInternational Union of Elevator Constructors, herebyenter into the following agreement, effective on andfrom June 1, 1953.One team of elevator constructors to not less than twoiron workers while installing the following: 1—cranerails, 2—crane bridges, 3—hoisting of all elevator equip-ment necessary to be in place before penthouse roof ispoured, 4—optional hoisting of crane drives, 5—allhatchway steel that replaces normal elevator hatchways,6—catwalks, platforms, stairways and ladders.The Bowser Engineering Company agrees to pay ironworkers the regular wage scale in the jurisdiction of theLocal Union in which the project is located plus 25 centsper hour to one iron worker who acts as foreman underthe supervision of the elevator mechanic on the job.Signed for International Association of Bridge, Struc-tural & Ornamental Iron Workers:JOHN J. MCCARTHY, Gen. Vice President.Signed for International Union of Elevator Construc-tors:J. A. ALTMAN, Reg. Business Representative. Attested July 10, 1953JOHN T. DUNLOPChairman National Joint Board.Boilermakers-IronworkersSeptember 23, 1953The undersigned representatives of the InternationalAssociation of Bridge, Structural and Ornamental Iron
87Workers and the International Brotherhood of Boiler-makers, Iron Shipbuilders, Blacksmiths, Forgers andHelpers recommend to the respective General Presi-dents the attached agreement for the settlement of juris-dictional disputes between the two organizations.(Signed) J. R. DOWNES,International Association of Bridge,Structural and Ornamental Iron Workers(Signed) J. P. MCCOLLUM,International Brotherhood of Boilermakers,Iron Shipbuilders, Blacksmiths, Forgers andHelpers.September 23, 1953Memorandum of AgreementThis memorandum of agreement between the Interna-tional Association of Bridge, Structural and OrnamentalIron Workers and the International Brotherhood of Boil-ermakers, Iron Shipbuilders, Blacksmiths, Forgers andHelpers supplements and interprets the agreement ofOctober 15, 1928 between the two organizations and thedecision of record of May 19, 1947.It is the purpose of this agreement to improve relationsbetween the two trades, to eliminate work stoppageswhich are costly to the membership of both organizationand to the industry, to settle jurisdictional disputes di-rectly between the two trades, and mutually to assisteach union to secure work coming within its recognizedjurisdiction. In order to achieve these objectives, it ismandatory upon the membership of local unions affili-ated with both International Unions to comply with theprovisions of this memorandum of agreement.
88It is expressly understood and agreed that this agree-ment shall not relate to or have any bearing on jurisdic-tional disputes that may exist or in the future occur, be-tween either of the parties hereto with any other Interna-tional Union or subordinate body thereof.1. WIRE MESH. Wire Mesh when attached or weldeddirectly to the breeching, stacks or vessels shall be in-stalled by Boilermakers, and wire mesh when attachedor fastened to lugs, clips, bolts, nuts or any other attach-ments (which have already been attached or welded tothe breeching, stacks or vessels by Boilermakers) shallbe installed by Iron Workers.2. DERRICKS. Where a derrick is used by both crafts,one craft shall erect and the other craft shall dismantlesame. Where such derrick is used only by one of thecrafts, then that craft shall erect and dismantle same.3. PRECIPITATORS. Plate work and buckstays and in-ternals shall be the work of the members of the Boiler-makers; structural supports shall be the work of the IronWorkers including the house roof. Roof supports or lugsattaching directly to the preciptator shell shall be thework of the Boilermakers. When roof supports attach tolugs, the Boilermakers shall weld the lug to the precipi-tator shell and the Iron Workers shall erect the roof sup-ports thereto.4. OVERHEAD SUPPORTING STEEL FOR STEAMGENERATORS.(a) The erection of structural members, which may bechannels, beams or angles, and which are directly at-tached to and suspended from the building roof steel forthe purpose of supporting the steam generating unitshall be the work of the Iron Workers.
89(b) The erection of all rods or other steel members at-tached to the members described in paragraph (a), andused for the purpose of supporting tubes and other Boil-ermakers’ work, shall be performed by the Boilermakers.5. THE ERECTION AND REPAIR OF BLAST FUR-NANCESThe following work items shall be erected and in-stalled by the Iron Workers:Foundation rod and bandsColumn bases and columnsMain, top furnace platform (except supports whichweld, or rivet to shell)Top super-structureBell trolleyBell beamsBell cablesJib-crane and mastAll top mechanism such as large bell, small bell, bellrods, large bell hopper, gas seal hood, distributor, re-volving hopper, receiving hopper and small bell seatSkip bridgeSkip cars and cablesSkip operating mechanism such as skip hoist, largeand small bell cylindersCast house structural steel and roofSkip houseSkip bridge A-frameIron and cinder runners and cast house auxiliariesTrestle and stock house parts such as coke, stone andore binsCoke and ore chutesScale car and larry carsPug mill machineryElevator shafts
90The following work items shall be erected and in-stalled by the Boilermakers:Hearth jacketHearth coolersTuyere jacketBlast furnace shellBustle pipeFurnace top ring and domeOfftakes—UptakesDowncomers and attached wearing platesBleeder pipe, valves and stackBosh bandDust catcherHot blast stovesHot blast valves and castingsGas washerGas mainsGas precipitatorsCold blast main and mixer lineStove stacksDust legsHot ladle carsSupport for main top furnace platform which weld orrivet to shellStock line brackets and abrasion or wearing platesTuyere stocks6. CATWALKS, PLATFORMS, STAIRWAYS AND LADDERS(a) Catwalks, platforms, stairways and ladders erected onstorage tanks for liquid or gas, and processing tanks erectedby the Boilermakers, and installations commonly referredto as tank farms shall be performed by Boilermakers.(b) Catwalks, platforms, stairways and ladders sup-ported exclusively by a pressure vessel, shall be erectedby Boilermakers.
91(c) Catwalks, platforms, stairways, and ladders sup-ported by structural steel supports shall be erected byIronworkers. When supported by both the pressure ves-sel and structural steel supports, the erection of the cat-walks, platforms, stairways and ladders shall be per-formed by Iron Workers, except that the welding or at-taching of the lug or support directly to the pressure ves-sel shall be performed by Boilermakers.(d) Catwalks, platforms, stairways, and ladders in con-nection with blast furnace construction shall be per-formed as follows:(i) The Boilermakers shall attach the lugs or sup-ports directly to the shell of the blast furnace and theIron Workers shall then erect the catwalks, platforms,stairways, and ladders.(ii) The erection of catwalks, ladders and stairwayson hot stoves and precipitators in connection with theblast furnace construction, in accordance with para-graph (b) of this section, shall be erected by Boiler-makers. The erection of the platforms and bridgewaysacross the top of hot stoves, however, shall be erectedby iron workers, except that the welding or attachingof the lugs or support directly to the hot stove shall beperformed by Boilermakers.7. FORCED AND INDUCED DRAFT FANS.The erection of forced and induced draft fans in connec-tion with the construction of steam generating installa-tions, which come in completed units, shall be performedby Iron Workers. Attachments to the ducts and breechingshall be performed by Boilermakers. On forced and in-duced draft fans, which come knocked down, the IronWorker shall erect and install the pedestal and rotor andthe Boilermakers shall erect and install the fan housing.
928. PROCEDURES.(a) The General President of each organization willdesignate a representative to be assigned to adjust di-rectly all disputes between the two trades which cannotbe adjusted at the local level.(b) Committees designated by the respective GeneralPresidents shall meet periodically to review work cov-ered by this agreement and to consider new problemswhich arise in order to adjust same.(c) Installations in process on the date of this agree-ment shall be completed in accordance with the existingassignments or ruling of the National Joint Board.International Association of Bridge, Structural and Orna-mental Iron Workers.St. Louis, Missouri.(Signed) J. H. LYONS,General President(Signed) J. R. DOWNES, General SecretaryApproved Nov. 2, 1953,General Executive Council.International Brotherhood of Boilermakers, Iron Ship-builders, Blacksmiths, Forgers and HelpersKansas City, Kansas.(Signed) CHAS. J. MACGOWAN,International President(Signed) WM. J. BUCKLEY, International Sec.-Treas.Approved Nov. 5, 1953,International Executive Council.
93Straight TelegramSt. Louis, Mo., November 2, 1953.Charles J. MacGowan, International PresidentInternational Brotherhood of Boiler Makers, Iron ShipBuilders and Helpers of AmericaNew Brotherhood BuildingKansas City, KansasThis is to notify you that the Executive Council of theInternational Association of Bridge, Structural and Orna-mental Iron Workers at its meeting today unanimouslyratified and adopted the memorandum of agreementdated September 23, 1953, which supplements and inter-prets the agreement of October 15, 1928, between ourtwo respective organizations as well as decision ofrecord of May 19, 1947.JOHN H. LYONS, General President.International Brotherhood of Boilermakers, IronShip Builders, Blacksmiths, Forgers and HelpersNovember 10, 1953.File: 12(i)-1(c) Mr. J. H. Lyons, PresidentIntl. Bridge & Structural Iron WorkersSte. 300, Continental Building3615 OliveStreetSt. Louis, MissouriDear Sir and Brother:Under date of November 6, 1953, I wired you as fol-lows:“This is to officially notify you that our InternationalExecutive Council after devoting a full day to the dis-cussion of the proposed memorandum of agreement
94dated September 23, 1953, which implements and in-terprets the agreement of October 15, 1928, finally ap-proved same by a unanimous vote of the ExecutiveCouncil. However, in the discussion it developed thatone or two minor clarifications may be necessary inorder to avoid future misunderstandings by our re-spective memberships. These clarifications will in nosense alter the purpose of the memorandum of Sep-tember 23, but will in truth and in fact be clarificationsonly. I shall write you the details of the same nextweek. I am furnishing John Dunlop with a copy of thistelegram.”Now, Brother Lyons, it is needless for me to say thatthe discussions in our International Executive Councilwere long and earnest over the question of approving theproposed supplementary agreement. While it was finallyadopted by a unanimous vote, it was the feeling of theInternational Executive Council that there was one prin-ciple involved which should be protected, from ourstandpoint, and there were at least two additional clarifi-cations which should be incorporated in order to makethe understanding as effective as possible.The principle to which I refer was the question of ourcraft deviating from our historic position that all vesselsrequiring tight joints must be the work of the Boilermak-ers and the allotment of the bells in blast furnaces to anyother trade was a departure from our traditional policy. Iassure you it was not the amount of work involvedwhich caused us our difficulty, but rather the principle ofa “tight joint.” However, in our earnest desire to reach apeaceful understanding between the two InternationalUnions, we accepted the assignment of bells, but withthe hope that the two Internationals could agree to an in-terpretation to be added as a footnote to the first portion
95of section 5 captioned, “The Erection and Repair of BlastFurnaces,” this footnote to read substantially as follows:“It is mutually agreed between the two InternationalUnions that the awarding of the blast furnace bells tothe Structural Iron Workers is without prejudice to theBoilermakers’ historic claims over all vessels requir-ing tight joints.” In the second portion of section 5, which is the Boiler-makers’ list of work, it occurred to us that the negotia-tors unintentionally overlooked the word “mantle” and ifit is agreeable to all parties, we would request that theword “mantle” be inserted in the proper place in the listof work awarded to the Boilermakers. Returning to section 4, captioned, “Overhead SupportingSteel for Steam Generators,” it was the opinion of our Inter-national Executive Council that while the intent of the twoorganizations is covered in this section, it was our feelingthat in order to avoid future disputes, the language needsclarifying, particularly where in sub-section (a) (Iron Work-ers’ section), the words “for the purpose of supporting thesteam generating unit” and in subsection (b) (Boilermak-ers’ section), the words “...used for the purpose of support-ing tubes and other Boilermakers’ work...” might be inter-preted in such a manner as to cause confusion because,after all, the complete boiler is still a steam generating unitfrom the standpoint of the Boilermaker and tubes are but apart of the steam generating unit. It is our suggestion thatafter the words “Boilermakers’ work” in the third line ofsection 4(b), the words “which are a part of the steam gen-erating unit” be added so that the whole section will read:“The erection of all rods or other steel members, at-tached to the members described in paragraph (a),and used for the purpose of supporting tubes and
96other Boilermakers’ work, which are a part of thesteam generating unit, shall be performed by the Boil-ermakers.”If it is agreeable with you, I would suggest that Secre-tary Downes and Vice President McCollum have a fur-ther meeting and see it if is not possible to work outthese suggestions, which, I repeat again, are not in-tended to change the intent of the agreement in any man-ner other than to clarify it to avoid confusion.With best wishes, I amFraternally yours,CHARLES J. MACGOWAN,International President.CJM:CWcc: John Dunlopcc: J. R. Downescc: J. P. McCollumOEIU No. 4-AFLInternational Association of Bridge, Structuraland Ornamental Iron WorkersJanuary 9, 1954Mr. J. P. McCollum, Vice PresidentInternational Brotherhood of Boilermakers, Iron ShipBuilders, Blacksmiths, Forgers and HelpersNew Brotherhood BuildingKansas City 11, KansasDear Sir and Brother:The correspondence dated November 10, 1953, di-rected by Charles J. MacGowan, International Presidentof the Brotherhood of Boilermakers, to J. H. Lyons, Gen-eral President of this International Association, as well
97as the correspondence dated November 13, 1953, fromGeneral President Lyons to International PresidentCharles J. MacGowan, has been reviewed by the writer.It is the opinion of the officials of this International As-sociation that the suggestions outlined by President Mac-Gowan warrant consideration and that, for the purpose ofclarification, further understandings should be developed.Inasmuch as the “Memorandum of Agreement” datedSeptember 23, 1953—and signed by yourself and thewriter—has been ratified by the International Executivecouncil of the Brotherhood of Boilermakers, and the Gen-eral Executive Council of this International Association, itis our opinion that no change should be made in this doc-ument as such action would require further ratificationfrom the Executive Councils of both organizations.It is agreeable to the officials of this International Asso-ciation that the following clarifications will be stipulated:“It is mutually agreed between the two InternationalUnions that the awarding of the blast furnace bells to theStructural Iron Workers is without prejudice to the Boiler-makers’ historic claims over all vessels requiring tight joints.”It is also understood that the work item “mantle”should be included in the Boilermakers’ division of Sec-tion 5 of the “Memorandum of Agreement.”It shall be understood that the meaning of Section 4,paragraph (b) of the “Memorandum of Agreement”—captioned OVERHEAD SUPPORTING STEEL FORSTEAM GENERATORS—shall be as follows:—“The erection of all rods and other steel members,attached to the members described in Paragraph (a)and used for the purpose of supporting tubes andother Boilermaker’s work, which are a part of the
98steam generating unit, shall be performed by the Boil-ermakers.”I believe that confirmation of these clarifications byInternational President Charles J. MacGowan and Gen-eral President J. H. Lyons, as well as yourself and thewriter, would be sufficient and thereby eliminate anyneed to reopen the present “Memorandum of Agree-ment” as ratified by both International Unions.I am, with best wishesFraternally yours,J. R. DOWNESJRD:HB General Secretary.January 18, 1954R. J. Gray, PresidentBuilding & Construction Trades DepartmentAmerican Federation of LaborWashington, D.C.Dear Mr. Gray:I am advised that you have received the agreementsigned by President J. H. Lyons and President Charles J.MacGowan, dated January 12, 1954 and identical com-munication which was sent to the National Joint Board.In accordance with Article III, Section 2 of the Agree-ment creating the Joint Board, I hereby attest to thisagreement.It is my understanding that the two organizations in-tend to print the agreement in convenient form in thenear future.Very truly yours,(Signed) JOHN T. DUNLOPChairmanJTD: thw National Joint board
99September 13, 1954Wm. J. McSorley, General PresidentWood, Wire and Metal Lathers International UnionAmbassador HotelLos Angeles, Calif.Dear Sir and Brother:At your request and in order to avoid any misunder-standings with the Wood, Wire and Metal Lathers Inter-national Union, the undersigned wish to advise that Sec-tion 1, captioned “Wire Mesh” of the Memorandum ofAgreement dated September 23, 1953, entered into be-tween the International Association of Bridge, Structuraland Ornamental Iron Workers and the InternationalBrotherhood of Boilermakers, Iron Ship Builders, Black-smiths, Forgers and Helpers is not intended and doesnot apply to the erection of light iron furring or metallath used to receive plaster.Fraternally yours,(Signed) WM. A. CALVIN,International President,International Brotherhood ofBoilermakers, Iron ShipBuilders, Blacksmiths,Forgers and Helpers(Signed) J. H. Lyons,General President,International Association ofBridge, Structural andOrnamental Iron Workers
100Asbestos Workers — BricklayersBoiler Wall ConstructionJanuary 28, 1954AGREEMENT BETWEEN THE INTERNATIONALASSOCIATION OF HEAT AND FROST INSU-LATORS AND ASBESTOS WORKERS AND THEBRICKLAYERS, MASONS AND PLASTERERS’INTERNATIONAL UNION OF AMERICA.(1) This agreement covers the installation and applica-tion of all insulating materials on boiler wall construc-tion.(2) In the application of insulating materials over theboiler walls after same is completed, when said insula-tion is applied in one continuous operation and not inconjunction with the refractory material, this is the workof members of the International Association of Heat andFrost Insulators and Asbestos Workers.(3) In cases where the insulation on the outside of theboiler walls is applied in conjunction with refractory ma-terials as it progresses (scaffold high), said insulation isthe work of members of the Bricklayers, Masons andPlasterers’ International Union of America.(4) In the event that a dispute over the application ofthis agreement cannot be settled locally, there shall be nostoppage of work, and the dispute shall be referred to theheadquarters of both International Unions for settlement.International Association of Heat andFrost Insulators and Asbestos Workers:(Signed) JOSEPH A. MULLANEY,HUGH E. MULLIGAN,C. W. SICKLES.
101Bricklayers, Masons and Plasterers’ Inter-national Union of America:(Signed) HARRY C. BATES,JOHN J. MURPHY,THOMAS F. M URPHY,A. J. CLELAND.Attested:John T. Dunlop, Chairman,National Joint Board for Settlementof Jurisdictional Disputes.February 2, 1954.
102DECISIONS OF A. F. OF L.DECISION OF AMERICAN FEDERAL OF LABORIN RE ISSUANCE OF CHARTER TO ELEVATORCONSTRUCTORS’ INTERNATIONAL UNION.WASHINGTON, D.C. May 9, 1904.MR. HENRY SNOW, Gen. Sec-Treas.International Union of Elevator Constructors40 Park Avenue, Chicago, Ill.Dear Sir and Brother:Today, Brothers Feeney and Havenstrite, of your or-ganization, called at this office and requested a definitestatement regarding matters of jurisdiction of your Inter-national Union.Of course, you are aware that the same subject wasunder discussion at the Denver meeting of the ExecutiveCouncil of the American Federation of Labor held lastmonth.Desirous of rendering the very best possible service Ican to your organization, consistent with the rights towhich all other organizations are entitled I therefore begto say that at the time when your organization appliedfor charter, from the American Federation of Labor, thefollowing claims to work were embodied in your appli-cation:“The assembling of all elevator machinery, to wit: Hy-draulic steam, electric, belt and compressed air; also as-sembling and building escalators, or traveling stairways;the assembling of all cars complete; putting up allguides, either of wood or iron; the setting of all tanks,whether pressure, open or pit tanks; the setting of allpumps (where pumps arrive on job in parts, they are to
103be assembled by members of this union). All electricwork connected with car machinery and hoisting, in-cluding bells, annunicators and lights; all overheadwork, either of wood or iron, and supports for the samewhen required; the setting of all templets, all indicators;all foundations, either of wood or iron, that would takethe place of masonry; the assembling of all hydraulicparts in connection with elevators; all locking devices inconnection with elevators; the boring, drilling and sink-ing of all plunger elevators; all link belt carriers, and allwork in general pertaining to the erection and equip-ment of an elevator complete.”Prior to issuance of the charter to your organization,claims to jurisdiction were made by several organiza-tions of some classes of work which were not allowed.Then an agreement was reached between the represen-tatives of the International Union of Elevator Construc-tors and the International Brotherhood of ElectricalWorkers, by which your organization yielded to the elec-trical workers the following classes of work: “The elec-trical work on flashlights, electrical annunciators andlamps, and feed wires to the controller.” With that reser-vation, and with those claims made by your organizationto jurisdiction, the charter was issued by the AmericanFederation of Labor.Fraternally yours,(Signed) Samuel Gompers,President American Federation of Labor
104DECISION OF THE AMERICAN FEDERATION OFLABOR IN RE JURISDICTION OF ENGINEERS.(Decision Norfolk, Va., Convention, American Federation ofLabor, November 11-23, 1907, Resolution No. 124.)Resolved, That hoisting and portable local unions ofthe International Union of Steam Engineers have juris-diction over the motive power of all derricks, cement-mixers, hod-hoists, pumps, and other machines used onconstruction work and be it furtherResolved, That the Building Trades organizations berequested to give all the assistance possible to the Hoist-ing and Portable Locals of the I. U. S. E. in maintainingthe scale of wages now paid on this work.This shall not, however, be construed as preventingthe International Brotherhood of Electrical Workersfrom using a hand or electric winch for the purpose ofpulling wire or cable through conduits, nor the wiringand repairing of all electrical appliances.DECISION OF AMERICAN FEDERATION OFLABOR ELECTRICAL WORKERS—ENGINEERS.(Decision Cincinnati, Ohio, Convention, American Federationof Labor, June 1922.)That the electrical installation, electrical repairs, over-hauling of general electrical apparatus in generating sta-tions, substations and the operating of exclusively elec-trical-driven machines in the aforementioned plants orstations also that the operation of traveling or other elec-tric cranes for shop or factory purposes shall be Electri-cal Workers work.“This decision is not to interfere with the jurisdictionof the Steam and Operating Engineers over operating
105steam-generating plants, electric hoists in building con-struction or electric shovels.These conclusions are not intended to disturb anyother conditions obtained that are mutually satisfactoryat this time, or that have been provided for by past ac-tion of the American Federation of Labor which are notin conflict with this decision.”DECISION OF AMERICAN FEDERATION OFLABOR IN RE DISPUTE BETWEEN TEAM-STERS AND IRON WORKERS.The following is a decision of jurisdiction dispute ex-isting between the International Brotherhood of Team-sters, Chauffeurs, Stablemen and Helpers of America,and the Bridge and Structural Iron Workers’ Interna-tional Union, rendered by an Arbitration Committee ap-pointed by the Executive Council and adopted by theConvention of the American Federation of Labor held inPortland, Oreg., October, 1923:“It is clearly evident that the Bridge and StructuralIron Workers’ International Union has gradually and per-sistently encroached upon the jurisdiction of the Inter-national Brotherhood of Teamsters, Chauffeurs, Stable-men and Helpers of America. It has constantly endeav-ored to broaden the jurisdiction by claiming, and insome instances practicing the rights to load and unloadmaterials off and on wagons, trucks, and automobiles. Inthe opinion of the Committee, this work clearly belongsto the International Brotherhood of Teamsters, Chauf-feurs, Stablemen and Helpers of America. This work wasconceded to this organization through its charter of affil-iation with the A. F. of L. All loading, hauling and unload-ing of materials on and off wagons, trucks and automo-biles belong to the International Brotherhood of Team-
106sters, Chauffeurs, Stablemen and Helpers of America.However, where building material is hauled to buildingsunder construction and the foreman, contractor, or per-son in charge of the erection of the building, directs thatit be hoisted from the wagon, truck or automobile, suchhoisting shall be done by the members of the Bridge andStructural Iron Workers’ International organization.Where it is loaded from the wagon, truck or automobileon the ground, street or sidewalk, such work shall bedone by the members of the Brotherhood of Teamsters,Chauffeurs, Stablemen and Helpers of America.”DECISION OF AMERICAN FEDERATION OFLABOR IN RE ERECTION OF ECONOMIZERS.(Decision El Paso, Tex., Convention, American Federation ofLabor, November 17-25, 1924.)In the controversy existing between the Brotherhoodof Boiler Makers and the United Association ofPlumbers and Steam Fitters over the erection of econo-mizers, the decision is that in the opinion of the Execu-tive Council the work belongs to the United Associationof Plumbers and Steam Fitters.United Association of Journeymen Plumbers andSteamfittersBy the decision of the American Federation of Labor,rendered at both the Atlanta and Rochester conventions,the substance of this action of these conventions of theAmerican Federation of Labor was that there was onlyroom for one organization in the pipefitting industry.And, that the United Association of JourneymenPlumbers and Steamfitters is recognized as the only or-ganization having complete control of the pipefittingtrade and industry in its entirety throughout the UnitedStates and Canada.
107Following are the official decisions of the AmericanFederation of Labor:Atlanta DecisionThe Atlanta Convention of the American Federationof Labor, held in Atlanta, Ga., November 13 to 25, inclu-sive, 1911, declared “that both for harmony and practi-cability the pipefitting trade should be represented inthe American Federation of Labor, also in the BuildingTrades Department, by one general association of thepipefitting industry, namely the United Association ofPlumbers, Gas Fitters, Steamfitters and Steamfitters’Helpers of the United States and Canada, and further,that the Executive Council of the Building Trades De-partment be requested to carry that declaration into ef-fect.” (See page 339 of the 1912 Rochester Conventionproceedings.)Rochester DecisionThe Adjustment Committee’s report to the delegatesassembled at the Rochester Convention of the AmericanFederation of Labor, held at Rochester, N.Y., November11 to 23, inclusive, 1912, is as follows:Your committee reports that it has considered care-fully the efforts made by the Executive Council of theAmerican Federation of Labor to carry out and make ef-fective the instructions of the Atlanta Convention, whichdeclared that both for harmony and practicability thepipefitting trade should be represented in the AmericanFederation of Labor, also in the Building Trades Depart-ment, by one general association of the pipefitting indus-try, namely, the United Association of Plumbers, Gas Fit-ters, Steamfitters and Steamfitters’ Helpers of the UnitedStates and Canada.
108DECISIONS RENDERED BY THE NATIONALBOARD FOR JURISDICTIONAL AWARDS INTHE BUILDING INDUSTRY.Air Coolers, Air Washers and Blowers, Consistingof the Assembling of Sheet Metaland Pipe FittingDECISION RENDEREDMARCH 11, 1920(Subject of dispute between the Amalgamated Sheet MetalWorkers’ International Alliance and the United Associa-tion of Plumbers and Steamfitters.)The following agreement, between the AmalgamatedSheet Metal Workers’ International Alliance and theUnited Association of Plumbers and Steamfitters wasconfirmed:September 9, 1918.The undersigned committee, appointed by the GeneralPresidents of their respective International Organiza-tions namely, the United Association of Plumbers,Steamfitters and Steamfitters’ Helpers and the Amalga-mated Sheet Metal Workers’ International Alliance, heldjoint conferences in the City of New York, beginningSeptember 5, 1918 in an endeavor to arrive at an agree-ment concerning air washers, fans, blowers, the housingof same, and the pipe fitting on same.After lengthy meetings participated in by all of the un-dersigned, representing the Joint Conference Committeeof both International Unions, the following has beenagreed to:SECTION 1. That all sheet metal work of No. 10 gauge orlighter, when used in air washers, fans, blowers, or on
109the housing of same, shall be recognized as being thework of the members of the Amalgamated Sheet MetalWorkers’ International Alliance.Sec. 2. That all pipe fitting in connection with theabove first section shall be recognized as being the workof the Steamfitters, members of the United Associationof Journeymen Plumbers, Steamfitters and Steamfitters’Helpers.Sec. 3. It being thoroughly understood by all of the un-dersigned that all the assembling and erecting of thework as defined in Section One, shall be the work of themembers of the Sheet Metal Workers’ International Al-liance, excepting pipe fitting of all kinds, which shall bethe work of the Steamfitters and Steamfitters’ Helpers ofthe United Association.Sec. 4. This agreement shall become effective and infull operation for all parties concerned beginning No-vember 1, 1918.Signed for Sheet Metal Workers this 9th day of Sep-tember, 1918:JAMES LENNON, Gen. Org.R. PATTISON, Chairman,W. M. O’BRIAN, Secretary,WM. H. LYONSTHOS. WALSH,EDW. P. O’NEIL.Signed for United Association:E. W. LEONARD, Gen. Org.CHARLES M. RAU,RICHARD P. WALSH,A. P. JOHNSON, LEO A. MURPHY.
110Low Pressure Heat(Subject of dispute between the United Association ofPlumbers and Steamfitters and the International Unionof Steam Engineers in the Matter of maintaining tempo-rary heat while structure is in course of construction.)DECISION RENDERED MARCH 11, 1920In the matter of the controversy between the engineerand steamfitter on the question of low pressure heat dur-ing completion of the heating system jurisdiction shallrest with the steamfitters until the initial test is com-pleted, immediately after which time, whenever neces-sary to maintain heat, a stationary engineer shall be em-ployed either by the contractor or the owner.Low Pressure Heat (Rehearing)(Subject of dispute between the International Union of SteamEngineers and United Association of JourneymenPlumbers and Steamfitters.)DECISION RENDERED AUGUST 2, 1923In the matter of the controversy between the engi-neers and steamfitters on the question of low pressureheat during completion of the heating system while thebuilding is under construction, jurisdiction shall restwith the steamfitters until the general test has beenmade and the work accepted by the owner or his agent.Pipe Railing or Guards for Enclosures, Stairways,Hatches, etc.(Subject of dispute between the Bridge and Structural IronWorkers’ International Association and the United Asso-ciation of Plumbers and Steamfitters. Claimed by theIron Workers entirely except when not used as a conduitfor fluids or vapors claimed by Plumbers and Steamfit-ters when of standard-sized cut and threaded pipe.)
111DECISIONRENDERED MARCH 11, 1920Pipe railing consisting of standard-size cut andthreaded pipe, not used in connection with structural orornamental iron work, is awarded to Plumbers andSteamfitters.INTERPRETATION RENDERED SEPTEMBER 15, 1920“Iron pipe railing consisting of a preponderance ofslip-joints made rigid with or without set-screws, pinionsor rivets, supported by a threaded joint and flange atbase or walls, is the work of the Iron Workers. Where,however, the preponderance of joints is of standard-sized cut and threaded iron pipe, it belongs to thePlumbers and Steamfitters.”Re-enforced Concrete, Cement and FloorConstruction(Subject of dispute between the Bridge and Structural IronWorkers’ International Association and the Wood, Wireand Metal Lathers’ International Union.)DECISION RENDERED MARCH 11, 1920In the matter of the controversy between the IronWorkers and Lathers over re-enforced concrete con-struction, it is decided that all iron and steel used for re-enforcement in re-enforced concrete, cement and floorconstruction be awarded to the Iron Workers.In such cities and localities as are covered by exist-ing agreements with employers awarding Lathers con-trol over re-enforced concrete construction, theseagreements are to be maintained inviolate until thedate of their expiration, after which this decision shallprevail.
112INTERPRETATIONRENDERED DECEMBER 4, 1920In the interpretation of this Board’s decision of March11, 1920, in the matter of the controversy between theIron Workers and Lathers over re-enforced concrete con-struction, it is not be understood as abrogating, settingaside or in any way altering the decision of the RochesterConvention of the Building Trades Department, Novem-ber 29, 1912, awarding jurisdiction over Hy-rib Lath to theLathers, and it is to be understood that the placing of Hy-rib Lath or any ribbed metal lath, however it may be used,comes within the jurisdiction of the Lathers.Vitrolite and Similar Opaque Glass(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and the Brotherhood ofPainters, Decorators and Paperhangers.)DECISION RENDERED MARCH 11, 1920That in the matter of the controversy between thePainters and Bricklayers on the subject herewith re-ferred to, jurisdiction over the setting of vitrolite andsimilar opaque glass is awarded to the Bricklayers.Vitrolite and Similar Opaque Glass (Rehearing)(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and the Brotherhood ofPainters, Decorators and Paperhangers.)DECISION RENDERED MAY 26, 1924It is the opinion of the Board that the foregoing deci-sion of March 11, 1920, is intended to convey to theBricklayers all counters and lavatories constructed ofvitrolite or carrara glass and such glass when used inmural decorations on buildings in place of marble or
113other stone or used in conjunction with marble or otherstone as panels on counters.It is the further opinion of the Board that the foregoingdecision is intended to convey all vitrolite, opalite, whiteopal and other opaque glass installed on false work, fur-ring strips, walls, ceilings, partitions or columns, se-cured with screw rosettes, molding, putty, expansion,toggle bolts or screws, to the Painters.The agreement of December 5, 1910, which was con-curred in by the Board of Awards on July 12, 1922, re-mains in effect, and any disputes that may arise in connec-tion with the subject of the agreement with the Board’sdecisions shall be adjusted in accordance with the provi-sions contained in Sections 3 and 4 of the agreement.Asbestos Plaster for Boiler Rooms, etc.(Subject of dispute between the Operative Plasterers and Ce-ment Finishers’ International Association and the Inter-national Association of Heat and Frost Insulators andAsbestos Workers.)DECISION RENDERED APRIL 28, 1920In the dispute between the Asbestos Workers andPlasterers on the matter of plastering boiler rooms, etc.,it is decided that the insulation and finishing coat on ceil-ings with asbestos and other insulating material, wherethe groundwork has been prepared and installed by theAsbestos Workers, shall, including the application of in-sulating material on boilers, tanks, vats, etc., be awardedto the Asbestos Worker.Light Iron Furring, Brackets, Clips, Hangers, Cor-ner Guards, Beads and Metallic Lath(Subject of dispute between the International Union of Wood,
114Wire and Metal Lathers and the International Associationof Bridge and Structural Iron Workers.)(Award of the Denver Convention, Building Trades Department,A. F. of L. adopted November, 1908. See printed proceed-ings, Pages 69 to 71, inclusive.)DECISION RENDERED APRIL 28, 1920In the matter of dispute between the InternationalUnion of Wood, Wire and Metal Lathers and the Interna-tional Association of Bridge and Structural Iron Workersreferred to in the foregoing title, the following award isconcurred in:“After going into an extended hearing of the jurisdic-tion claims of both organizations, your committee rec-ommends that the erection and installation of all lightiron work, such as light iron furring, brackets, clips,hangers, steel corner guards or beads.* and metallic lath-ing of all descriptions belong solely to the Lathers.“This does not give the right, however, to the Lathersto install or erect any other iron work that as hereinspecified and outlined.“This decision is based on conformity with the agree-ment entered into by the national officers of both organ-izations and endorsed by the Kansas City Convention ofStructural Iron Workers and concurred in by the Ameri-can Federation of Labor.”Hy-Rib LathIn supplement of the foregoing decision the RochesterConvention of the Building Trades Department, Novem-ber 29, 1912, awarded jurisdiction over Hy-rib Lath to theLathers.(Note interpretation rendered December 4, 1920, re-enforcedConcrete, Cement and Floor Construction.)*Note the following decision.
115Metallic Corner Beads When Set in PlasticMaterial(Subject of dispute between the Operative Plasterers and Ce-ment Finishers’ International Association and the Wood,Wire and Metal Lathers’ International Union.)DECISION RENDERED MARCH 11, 1920In the matter of the controversy between the Plaster-ers and Lathers on the question of the adherence of cor-ner beads by plastic material, it is the opinion of theBoard that deserved consideration was not given thesubject when the previous decision was reached. It istherefore agreed that the Plasterers are awarded juris-diction over sticking with plastic material metallic cor-ner beads.Acetylene and Electric Welding(Subject of dispute between the trades named in the followingmemorandum.)DECISION RENDERED APRIL 28, 1920In the matter of the dispute referred to in the forego-ing title, as approved by the Philadelphia Convention ofthe Building Trades Department, A. F. of L. November,1914 (see printed proceedings, Page 99), the followingagreement is concurred in:“Representatives of the Electrical Workers, SheetMetal Workers, Iron Workers, Plumbers and Steamfitter,and Machinists mutually agreed to the following deci-sion:“Each trade to have jurisdiction over all acetylene andelectric welding when such process is used to performthe work of their respective trades.”
116Bronzing and Painting of Radiators and PipeConnections(Subject of dispute between the Brotherhood of Painters, Deco-rators and Paperhangers and the United Association ofPlumbers and Steamfitters.)(Award of Rochester Convention, Building Trades Depart-ment, A. F. of L. adopted November 29, 1912. See page141, printed proceedings.)DECISION RENDERED APRIL 28, 1920In the matter of the subject referred to in the forego-ing title, the following award is concurred in:Resolved, that the United Association of Plumbers andSteamfitters be and is instructed to require that its affili-ated unions desist from further trespass upon the juris-diction of the Brotherhood of Painters, Decorators andPaperhangers of America, and when and where neces-sary to notify their employers that neither journeymennor helpers will be permitted to do this work.Application of Damp-Resisting Preparations andWaterproofing(Subject of dispute between United Slate, Tile and CompositionRoofers, Damp and Waterproof Workers’ Associationand the Brotherhood of Painters, Decorators and Paper-hangers.)DECISION RENDERED APRIL 28, 1920In the matter of dispute referred to in the foregoingtitle, the following agreement is concurred in:Agreement entered into by and between the Brother-hood of Painters, Decorators and Paperhangers of Amer-ica and the United Slate Tile and Composition Roofers,Damp and Waterproof Workers’ Association.
117First. That the Painters do not claim the right to applyany of the material claimed by the Slate, Tile and Com-position Roofers, Damp and Waterproof Workers, exceptsuch material as is applied by a brush that is ordinarilyused by the Painters in applying the materials covered intheir jurisdiction.Second. That the Slate, Tile and Composition Roofers,Damp and Waterproof Workers do not claim the right toapply any of the material in dispute except when appliedby or with a three-knot, long-handled brush, mop, orswab, and spray system employed therein.Erection of Scaffolds as Applied to BuildingConstruction(Subject of dispute between the International Hod Carriers’,Building and Common Laborers’ Union, United Brother-hood of Carpenters and Joiners, Operative Plasterers andCement Finishers’ International Association and Brick-layers, Masons and Plasterers’ International Union.)DECISION RENDERED APRIL 28, 1920In the matter of the dispute between the Laborers,Bricklayers, Plasterers and Carpenters over the erectionof scaffolds as applied to building construction, it isagreed that the erection and removal of all scaffolds, in-cluding trestles and horses used primarily by Lathers,Plasterers, Bricklayers and Masons, shall be done by themechanics and laborers in these trades as directed bythe employer.Self-supporting scaffolds over fourteen feet in heightor any special designed scaffolds or those built for spe-cial purposes shall be built by the Carpenters.The making of horses and trestles other than tempo-rary is the work of the Carpenter.
118Marble and Slate Partitions, Backs and FloorSlabs for Urinal Stalls, Closets andShowers, Setting of(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and the United Association ofPlumbers and Steamfitters.)(Award of Rochester Convention, Building Trades Department,A. F. of L. adopted November 28, 1912. See page 132,printed proceedings. Award of Buffalo Convention, No-vember 9, 1917. See page 92, printed proceedings.)DECISION RENDERED APRIL 28, 1920In the matter of the subject referred to in the forego-ing title, the following award is concurred in:Resolved, That the setting of floor slabs, backs, parti-tions of urinal stalls, closets and shower baths properlybelong to the Bricklayers.The foregoing decision does not concede to the Brick-layers the right to install marble work that is connectedwith the water supply or sewer or water-tight work regu-larly catalogued as plumbing fixtures.Muslin and Canvas for Decorative Purposes,Tacking of(Subject of dispute between the Brotherhood of Painters, Deco-rators and Paperhangers and the I. A. Heat and Frost In-sulators and Asbestos Workers.)(Award of Buffalo Convention, Building Trades Department, A.F. of L. adopted November 10, 1917. See page 108,printed proceedings.)DECISION RENDERED APRIL 28, 1920In the matter of the subject referred to in the forego-ing title, the following award is concurred in:
119Resolved, That this convention notify and instruct theofficers of the Asbestos Workers’ International Unionthat the tacking of all muslin and canvas for decorativepurposes is the jurisdiction of the Painters and that theyinstruct their members to refrain from doing any of thiswork.Pile Driving Machinery and Engines, Operation of(Award of Buffalo Convention, Building Trades Department, A.F. of L. adopted November, 1917. See pages 59 and 105,printed proceedings.)DECISION RENDERED APRIL 28, 1920In the matter of the subject referred to in the forego-ing title, the following award is concurred in:Such workmen as are employed in the operation of en-gines or machinery in connection with a pile driver comeunder the jurisdiction of the Engineers.Sheet Metal Glazing for Sash, Frames, Doors,Skylights, etc.(Subject of dispute between the Brotherhood of Painters, Deco-rators and Paperhangers and Sheet Metal Workers’ Inter-national Association.)DECISION RENDERED APRIL 28, 1920In the matter of the dispute referred to in the forego-ing title, the following agreement is concurred in:Agreement entered into by and between the GeneralExecutive Board of the Brotherhood of Painters, Deco-rators and Paperhangers of America, and the SheetMetal Workers’ International Association shall take ef-fect December 1, 1910, and remain in force untilamended, revised or changed at a meeting between the
120representatives of both organizations called for this pur-pose.SECTION 1. It is agreed by both parties to this agree-ment that all glass set in sheet metal sash, frames, doorsor skylights, shall be set by Painters, according to theirclaim of jurisdiction granted by the convention of theBuilding Trades Department, A. F. of L. at St. Louis, De-cember, 1910; and that all sheet metal work on sheetmetal sash, frames, doors or skylights shall be done bySheet Metal Workers.SEC. 2. In localities where differences now exist or mayarise in the future, such differences shall be adjusted by acommittee appointed by and representing the districtcouncils or local unions of both organizations in that lo-cality. Should this committee be unable to agree, a repre-sentative of the General Executive Board of each organi-zation shall be called in to assist in the adjustment.SEC. 3. It is also agreed that the national officers of bothorganizations where local unions fail to agree shall insistthat this agreement be carried out by affiliated unions.Slate Treads When Set on Iron Stair Case(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and the International Associ-ation of Bridge and Structural Iron Workers.)In the matter of the subject referred to in the forego-ing title, the following award is concurred in:DECISION RENDERED APRIL 28, 1920Slate treads on iron stairs having provoked a disputein jurisdiction between the organizations above named,was submitted to the Executive Council, November 20,1909. The action taken follows:
121The Executive Council of the Building Trades Depart-ment, on being called upon for a decision, awarded thework in question (slate treads) to the Bricklayers.Unskilled Labor, with Special Reference to theLoading and Unloading of Material as Appliedto Re-enforced Concrete Construction(Subject of dispute between the International Hod Carriers,Building and Common Laborers’ Union and InternationalAssociation of Bridge and Structural Iron Workers.)DECISION RENDERED AUGUST 2, 1920AMENDED DECEMBER 11, 1924It is the decision of the Board that the loading and un-loading, carrying and handling of all rods and materialsfor use in re-enforcing concrete construction shall bedone by laborers under the supervision of such personsas the employer may designate. The hoisting of rodsshall be done by laborers, except when a derrick or out-rigger operated by other than hand-power is used. Thisdecision applies only to the character of work stipulatedherein. In such localities where existing agreements pro-vide otherwise, this decision is to become effective atthe expiration thereof.Defects in Concrete Caused by Leakage, Bulging,Sagging, etc., Through Defective or Shifting Forms(Subject of dispute between the Operative Plasterers and Ce-ment Finishers’ International Association and the Inter-national Hod Carriers, Building and Common Laborers’Union.)DECISION RENDERED AUGUST 2, 1920When finishing tools are not used or required, thework shall be done by the laborer.
122The filling of voids and other work requiring patching,where finishing tools are used and required, shall bedone by the cement finisher.Setting and Alignment of Tile and PorcelainBathroom Accessories(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and the United Association ofPlumbers and Steamfitters.)DECISION RENDERED DECEMBER 4, 1920In the matter of controversy between the Tile Layersand Plumbers over setting and Alignment of Tile andPorcelain Bathroom Accessories, it is decided that allbath and toilet room accessories made of clay products,built-in tile-faced walls, shall be the work of the tile set-ter.Anchors for Bathroom Accessories(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and the United Association ofPlumbers and Steamfitters.)DECISION RENDERED NOVEMBER 14, 1923All bathroom accessories, except those covered bydecision rendered December 4, 1920, placed after fin-ished tile wall surfaces are completed, shall be set byPlumbers and Steamfitters. When anchors for bath-room accessories are built into finished tile wall con-struction, the setting of same shall be done by Brick-layers and Masons and when any such anchors areplaced after finished tile wall surfaces are com-pleted, the work shall be done by Plumbers andSteamfitters.
123Jurisdiction Over Foremen on Interior ConcreteColumns, Foundations for Engine andMachinery Beds(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union, International Hod Carriers,Building and Common Laborers’ Union and the Opera-tive Plasterers and Cement Finishers’ International Asso-ciation.)DECISION RENDERED DECEMBER 4, 1920In the matter of the jurisdiction over Foremen on Inte-rior Concrete Columns, Foundations for Engine and Ma-chinery Beds as contested by the Bricklayers, Hod Car-rier and Plasterers, it is the decision of the Board thatthe work shall be done by the Laborers under the super-vision of such skilled workmen as the employer maydesignate.Electrical Work on Elevators (Rehearing)(Subject of dispute between the International Brotherhood ofElectrical Workers and the International Union of Eleva-tor Constructors.)DECISION RENDERED DECEMBER 4, 1920REVISED AND AMENDED FEBRUARY 2, 1927In the matter of dispute between the Elevator con-structors and the Electrical Workers on the question ofall electrical work on elevators, it is agreed that the elec-trical work involved in the installation of signal systems,fans, telephones, electric light fixtures, illuminatethresholds and feed wires to the controller on all eleva-tors is the work of the Electrical Workers; also the elec-trical work in connection with interlocking devices onother than automatic elevators is awarded to the Electri-cal Workers.
124The term “automatic elevator,” as used in this award,includes the full automatic, double push-button singlecontrol and department store control elevators.Bishopric Board, When Applied as a Substitutefor Lath and Sheathing(Subject of dispute between the United Brotherhood of Carpen-ters and Joiners and the International Union of Wood,Wire and Metal Lathers.)DECISION RENDERED DECEMBER 4, 1920In the matter of the dispute over the installation ofBishopric Board when applied as a substitute for lath, itis the decision of the Board that the work shall be doneby the Lathers; where the same is used for sheathing itshall be the work of the Carpenters.Flaxlinum Keyboard Insulation(Subject of dispute between the United Brotherhood of Carpen-ters and Joiners and the International Union of Wood,Wire and Metal Lathers.)DECISION RENDERED DECEMBER 4, 1920In the matter of the dispute over the installation ofFlaxlinum Keyboard and Insulation, it is the decision ofthe Board that when the same is used as a substitute forlath or when any plastic material is to be applied, thework shall be done by the Lathers; when Flaxlinum isused as insulation or sheathing it shall be the work of theCarpenters.Installation of Metal Windows(Subject of dispute between the Sheet Metal Workers’ Interna-tional Association and the International Association ofBridge and Structural Iron Workers.)
125DECISIONRENDERED MAY 5, 1926The installation of metal windows having cast-ironsills and cast-iron blocks or in which three or more ofthe structural parts—that is, the sills, head, jambs andmullions—are heavier than ten-gauge, shall be the workof the Iron Workers; otherwise it shall be the work of theSheet Metal Workers.Hoisting, Lowering and Placing of ElevatorMachinery(Subject of dispute between the Elevator Constructors’ Interna-tional Union and the International Association of Bridgeand Structural Iron Workers.)DECISION RENDERED FEBRUARY 7, 1922In the matter of the dispute between the Elevator Con-structors and Bridge and Structural Iron Workers re-ferred to in the foregoing title, it is decided that the Ele-vator Constructors be awarded the hoisting, loweringand placing of elevator machinery.Glazing as Hereinafter Described(Agreement for avoidance of dispute between Brotherhood ofPainters, Decorators and Paperhangers and Bricklayers,Masons and Plasterers’ International Union as endorsedby Building Trades Department, A. F. of L.)DECISION RENDERED JULY 12, 1922In the matter of the subject referred to in the forego-ing title, it is the decision of the Board that the followingagreement be concurred in:Agreement entered into by and between the GeneralExecutive Board of the Brotherhood of Painters, Deco-rators and Paperhangers of America, and the General
126Executive Board of Bricklayers, Masons and Plasterers’International Union shall take effect December 5, 1910and remain in force until amended, revised or changedat a meeting between the representatives of both organi-zations called for this purpose.SECTIOn 1. It is agreed by both parties to this agree-ment that all plate and window glass, mirrors, beveledplate, rough, ribbed, wire, figured, colored, or art glassset in sash, frames, doors or skylights constructed ofwood, sheet metal, iron, stone or other material and setwith putty or moulding, shall be set by Painters, andthat where glass is used as a substitute for ceramic, mo-saic, or encaustic tile, and set on floors, walls and ceil-ings in mortar, cement or other plastic material used tosecure such tile in position, shall be set by Bricklayerswhen cut to size and shape for setting. It is furtheragreed by the Bricklayers that all glass delivered on jobsin stock sheets shall be cut to the required size by thepainters.SEC. 2. It is agreed by both parties to this agreementthat all plate and window glass, mirrors, beveled plate,rough, ribbed, wire, figured, colored, or art glass set insash, frames, doors or skylights constructed of wood,sheet metal, iron, stone or other material and set withputty or moulding, shall be set by the Painters, and thatwhere glass is used as a substitute for marble in interiorfinish or decoration, and is carved, cut, polished orrubbed, shall be set by the Bricklayers.SEC. 3. Should any differences arise regarding thework as covered by this agreement, a committee ap-pointed by and representing the district council or localunion of each organization in that locality, shall meetand adjust such differences. Should the committees ofthe local unions fail to agree, an executive officer of
127each international union shall be requested to attend andassist in the adjustment.SEC. 4. It is further agreed that the national officers ofboth organizations shall insist that all agreements en-tered into shall be carried out by affiliated unions.Operation of Elevators for Hoisting Materials(Decision of St. Louis Convention, Building Trades Department,A. F. of L. adopted December, 1910. See printed proceed-ings, Page 128.)DECISION RENDERED JULY 12, 1922In the matter of the subject referred to in the forego-ing title, the following decision is concurred in:The operation of elevators of all kinds when used forhoisting any material used in the construction of build-ings is hereby conceded to the Hoisting Engineers affili-ated with the International Union of Steam Engineers.Corrugated Sheeting(Subject of dispute between International Association of Bridgeand Structural Iron Workers and Sheet Metal Workers’International Association.)DECISION RENDERED MAY 26, 1923The erection of corrugated metal sheeting on steelframes construction when the sheets are simply end andside lapped is the work of the Iron Workers; the erectionof all other corrugated metal sheeting of No. 10 gauge orlighter is the work of the Sheet Metal Workers.Derricks, Erection and Handling for Setting Stone(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and International Associationof Bridge and Structural Iron Workers.)
128DECISIONRENDERED MAY 26, 1923 The stonesetter shall have sole jurisdiction over handderricks in connection with the setting of stone.The erection and operation of power derricks for set-ting stone shall be done by the Iron Workers, under thedirect supervision of the stone setter, who shall deter-mine the number of men to be employed.Artificial Stone—Granite (Dressing, Altering andFinishing)(Subject of dispute between Granite Cutters’ International As-sociation and Journeymen Stone Cutters Association.)DECISION RENDERED MAY 26, 1923In the matter of dispute between the Granite Cutters’International Association and the Journeymen StoneCutters’ Association relative to artificial stone, the dress-ing, altering and finishing of artificial stone, cast in imita-tion of natural stone, is the work of Stone Cutters, ex-cept that when any such artificial stone, by reason ofhardness of texture requires the use of granite cutters’tools for the proper dressing, altering or finishing, it isthe work of the Granite Cutters.Flat-face Tile(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and Union Slate, Tile andComposition Roofer, Damp and Waterproof Workers’ As-sociation.)DECISION RENDERED MAY 26, 1923In the matter of dispute referred to in the foregoingtitle, the following agreement is concurred in:
129Bricklayers, Masons and Plasterers’ International Union vs.United Slate, Tile and Composition Roofers, Damp andWaterproof Workers AssociationAgreement entered into this 21st day of February,1911, amended May 26, 1923, by and between duly ac-credited representatives of the organizations abovenamed, to wit:Jurisdiction is hereby conceded by the Bricklayersover the laying or setting of flat-faced tile of every de-scription when laid in mortar on all flat roofs or prome-nade roofs.Jurisdiction is hereby conceded the Slate, Tile andComposition Roofers, Damp and Waterproof Workersover flat-faced tile of every description, and corrugatedtile, when laid in any preparation of asphalt on roofs, flator otherwise.Foremanship Over Concrete Construction(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union, International Hod Carriers’Building and Common Laborers’ Union and OperativePlasterers and Cement Finishers’ International Associa-tion.)DECISION RENDERED MAY 26, 1923AMENDED FEBRUARY 21, 1924REVISED DECEMBER 11, 1924In the matter of dispute over concrete construction, itis decided the work shall be done by laborers under thesupervision of such skilled mechanic as the employermay designate.
130Conduo Base, Installation of(Subject to dispute between International Brotherhood of Elec-trical Workers and Sheet Metal Workers’ InternationalAssociation.)DECISION RENDERED AUGUST 2, 1923In the matter of the controversy between the Electri-cal Workers and the Sheet Metal Workers as to the instal-lation of conduo base, it is decided that the installationof conduo base is the work of the Sheet Metal Workers.Setting of Alberene Stone Slabs, Used as DrainBoards or Backs in Connection with Sinks(Subject to dispute between the Bricklayers, Masons and Plas-terers’ International Union and the United Association ofPlumbers and Steamfitters.)DECISION RENDERED NOVEMBER 14, 1923In the matter of the controversy between the Bricklay-ers and Masons and the Plumbers and Steam Fitters overthe Setting of Alberene Stone Slabs used as DrainBoards or Backs in Connection with sinks, it was de-cided that the setting of Alberene stone slabs used asdrain boards or backs in connection with sinks is thework of Plumbers and Steamfitters.Gunnite Work of Handling of Cement Gun(Subject to dispute between the International Hod Carriers, Build-ing and Common Laborers’ Union, Operative Plasterersand Cement Finishers’ International Association andBricklayers, Masons and Plasterers’ International Union.)DECISION RENDERED FEBRUARY 21, 1924In the matter of the dispute referred to in the forego-ing title, the following decision was reached:
131When work to be performed is to be of the thicknessof one and one-half inches or greater, the handling of thecement gun shall be done by the Laborers. When thework is less than one and one-half inches in thickness,the handling and control of the nozzle shall be the workof the Plasterers and Cement Finishers.It is understood that this decision does not allow theLaborers the right to finish where any finishing tools arerequired.The application of a coat of cement mixture by meansof the cement gun on steel, as a protection against corro-sion is not included in this decision.Plastering Work for Preparation of Walls andCeilings for Tiling(Subject to dispute between the Bricklayers, Masons and Plas-terers’ International Union and the Operative Plasterersand Cement Finishers’ International Association.)DECISION RENDERED FEBRUARY 21, 1924After reviewing the controversy in its various phases,the determination is reached that the agreement previ-ously existing between the two organizations affords themost practical plan of adjustment, and the followingaward is therefore made as the decision of the Board:Plasterers shall prepare or plaster all walls and ceil-ings which are to receive tile, except the final settingbed, which shall be applied by the Tile Layers; the bath-rooms, vestibule and small halls in single private resi-dences shall be plastered by the Tile Setters.Concrete Slab Re-enforced (Pre-Cast) forRoof Tiling(Subject of dispute between the Bricklayers, Masons and Plas-
132terers’ International Union and the United Slate, Tile andComposition Roofers, Damp and Waterproof Workers’Association.)DECISION RENDERED DECEMBER 11, 1924Jurisdiction is awarded Slate, Tile and CompositionRoofers, over pre-cast re-enforced concrete slabs forroof tiling when pointed up with or laid upon any prepa-ration of asphalt, roofing cements or other mastics, onroofs, flat or otherwise.When laid in cement, lime or gypsum mortars, thework is awarded to Bricklayers.Installation of Air Piping in Connection withElevator Door Locks(Subject to dispute between the United Association ofPlumbers and Steamfitters and the International Unionof Elevator Constructors.)DECISION RENDERED NOVEMBER 11, 1925When the compressor is used only for elevator work,the work from the water main to the compressor and re-turn shall be the work of the plumbers and steamfitters.The elevator constructor shall set the compressor anddo all the work between the compressor and the lockingdevice, but when the compressor is used for other pur-poses than elevator work, then the compressor shall beset by the plumbers and steamfitters, and the elevatorconstructor shall do the necessary piping from the com-pressor to his work only, all other work to be done bythe plumbers and steamfitters.Setting, Installing or Sticking of Artificial Stone(Subject of dispute between the Bricklayers, Masons and Plas-terers’ International Union and Operative Plasterers andCement Finishers’ International Association.)
133DECISION RENDEREDMAY 5, 1926It is decided that the setting, installing or sticking ofartificial stone, the material base of which is gypsum,plaster of Paris or Keene cement, resembling plaster incharacter and density, wherever used on the interior ofbuilding, whether or note reinforced with burlap orother fibrous material, regardless of color, or whether ornot faced with any special cement, whether pre-cast orrun in place, is the work of the Plasterers.Wherever artificial stone, the material base of which isof other cements, which comes pre-cast and resemblesthe natural stone in character and density, regardless ofcolor, whether or not faced with any special cement, thework is that of the Bricklayers.Cutting of Chases and Channels in Brick, Tile andother Masonry(Matter referred to National Board for Jurisdictional Awards byExecutive Council, Building Trades Department.)DECISION RENDERED MAY 5, 1926Inasmuch as no other trades except the Bricklayers,Plumbers and Steamfitters and Electricians haveclaimed this work, it is decided that the cutting of chasesand channels in brick, tile and other masonry is the workof the Bricklayers, except that the Plumbers and Steam-fitters and Electricians shall have jurisdiction to do cut-ting where required for the installation of their respec-tive work.Placing of Trap Rock Floors by Terrazzo Methods(Subject to dispute between the Bricklayers, Masons and Plas-terers’ International Union and Operative Plasterers andCement Finishers’ International Association.)
134DECISION RENDEREDMAY 5, 1926The finishing of cement floors where additional aggre-gate of stone is added by spreading or sprinkling on topof the finished base and troweled or rolled into the finishand then the surface ground by grinding machines, shallbe under the jurisdiction of the Terrazzo Workers. Whenno additional stone or aggregate is added to the finishedmixture, even though the surface may be ground, thework shall be under the jurisdiction of the Cement Fin-ishers.Jurisdiction Over Operation of Electric andTraveling Cranes During Construction of Building(Subject of dispute between the International Union of Steamand Operating Engineers and International Brotherhoodof Electrical Workers.)(Decision Executive Council, American Federation of Labor,March, 1926.)ADOPTED AUGUST 4, 1926“The Executive Council has been asked for an inter-pretation of decision rendered by the 1922 CincinnatiConvention of the American Federation of Labor, as itrelates to the jurisdiction of overhead or traveling cranesinstalled as a permanent fixture in building while build-ing is under construction and cranes are being used tohandle building material for the construction of buildingand also for the setting of motors, generators and otherelectrical equipment.The decision provides that the Engineers have juris-diction over the hoists for building material on buildingunder construction, and that the Electrical Workers havejurisdiction over the overhead or traveling cranes forshop or factory purposes. Therefore if the overhead or
135traveling cranes are used exclusively to handle buildingmaterial for the building, cranes shall be operated duringsuch construction by members of the Steam and Operat-ing Engineers.If motors and other electrical equipment are being setin place while building is under construction and a craneor cranes are used for such setting, the Engineers shalloperate the crane, handling both building material andelectrical equipment until 50 per cent of the motors orelectrical equipment are set, and then the Engineersshall cease to operate crane and shall turn same over tobe operated by Electricians, who will operate the cranefor all purposes thereafter.In the event of two overhead cranes being used to han-dle building material and electrical equipment, then onecrane shall be operated by Engineer and one be operatedby Electrician for all the work required of that crane, inwhich case each operator shall be employed until theplant is completed, when Engineer shall turn crane overto Electricians to operate.”
136DECISIONS RENDERED AND HELD TO BE OPER-ATIVE BY THE BUILDING AND CONSTRUC-TION TRADES DEPARTMENT.Jurisdiction Over Spot GroundsDECISION BALTIMORE CONVENTION, 1916All ground work, continuous or of spot character, forthe purpose of receiving trim, shall be done by the Car-penter; all spot ground work, when applied solely for theguidance of plastering work, shall be done by the Plas-terer.Plaster Boards or Substitute Materials ThereforJULY 25, 1919The erection or construction of plaster board ceilingsor partitions which are to receive plaster is the work ofthe Lather. This form of construction is fundamentallyand primarily a lathing feature, as is wire lath attachedto light iron furring. The studs or runners used in thisform of construction are in principle similar to light ironfurring as conceded to the Lather.Setting of Screeds in Cement Construction andForm WorkMARCH 17, 1920The decision is that setting screeds in connection withthe finishing of cement floors is conceded as CementFinishers work.Setting Electrical MotorsAUGUST 14, 1920Handling, setting and adjusting of motors and con-
137necting of power thereto is work of Electrical Workers.Fastening of motors direct to motor-driven machinery iswork of Millwrights.Boilers, Moving, Handling and PlacingOCTOBER 3, 1923Work in question being vital part of Steam Fittersequipment is therefore the work of the Steam Fitter.Holorib Deck RoofingJANUARY 26, 1928Have received the sample of Holorib deck roofing.This material being less than ten gauge, therefore, underthe rulings of this Department, the Sheet Metal Workershave jurisdiction.Steeltex Re-enforcementAUGUST 9, 1929Welded wire mesh steeltex used primarily for re-en-forcing is the work of the iron workers. Paper backsteeltex which performs the same function and is usedfor the same purpose as hy-rib is the work of the Lather.Bush Hammering of Concrete Base FoundationSEPTEMBER 23, 1930The bush hammering of concrete comes within the ju-risdiction of the Cement Finishers.Teamster-Engineer DecisionOCTOBER 27, 1939(Decision rendered by subcommittee of the Executive
138Council of the Building and Construction Trades Depart-ment, A. F. of L., and approved by the 34th Annual Con-vention of the Department, New Orleans, La., November,1940.)For a complete report of subcommittee see pages 138to 143, inclusive, of the Proceedings of the 34th AnnualConvention.DECISIONAll power-driven equipment that is used exclusively asa vehicle to transport any material or other matter forbuilding or other construction work comes within the ju-risdiction of the Teamsters and Chauffeurs.All power-driven equipment used on any and all typesof building and other construction work, including anyand all power-driven equipment that has been in disputebetween the Teamsters and Engineers, comes within thejurisdiction of the International Union of Operating En-gineers.WM L. HUTCHESON, Chairman.R. J. GRAY, Secretary,D. W. TRACY.January 29, 1940.The Executive Council,Building and Construction Trades Department, Ameri-can Federation of Labor.Your committee appointed to handle the matter of thedispute between the International Brotherhood of Team-sters, Chauffeurs, Stablemen and Helpers and the Inter-national Union of Operating Engineers received a re-quest from President Tobin of the Teamsters for a clarifi-cation of the decision.
139President Hutcheson, President Tracy and Mr. Graymet with Messrs. Tobin, Gillespie and Farrell on Sundayevening, January 28, and the Teamsters requested infor-mation on the following:1. On agreements on the Pacific coast, west of theRocky Mountains, which he claimed it would be impos-sible for him to immediately abrogate without consider-able difficulty.2. The matter of operation of what is known as trac-trucks which are used exclusively for the transportationof materials.3. The questions of the members of Teamster Unionswho had been employed as Chauffeurs on what isknown as a crane mounted on a truck chassis which isused exclusively in the New York metropolitan area.The conference adjourned after it was agreed thatyour committee would confer with the representativesof the Engineers on Monday, January 29.At the conference with the Engineers the followingwere present: John Possehl, Brothers Fay, Maloney andStuhr. President Possehl agreed that he would not callfor immediate operation of the decision that would af-fect any existing agreements on the Pacific coast, westof the Rocky Mountains. However, he expressly statedthat this would not apply to any agreements that mayhave been made after the decision of the committee hadbeen rendered.On question number two—on the operation of trac-trucks used exclusively to transport materials—the En-gineers agreed that the operation of such trucks is thework of the Teamster.The operation of trucks, which have a crane mounted
140on the truck chassis was next discussed. The Engineersagreed that they would accept any Teamster memberswho had been employed for any length of time in thedriving of these trucks to membership in their organiza-tion. Brothers Possehl, Fay and Delaney agreed to sitdown with representatives of the Teamsters as far as themetropolitan area of New York was concerned and ad-just the matter in a peaceful manner locally.WM. L. HUTCHESON,D.W. TRACY,R. J. GRAY.
141DECISIONS RENDERED BY DR. JOHN A. LAPP,NATIONAL REFEREE FOR THE BUILDING ANDCONSTRUCTION TRADES DEPARTMENT, A. F.OF L.Setting Wall Bearing Steel Bar JoistsDECISION RENDERED APRIL 23, 1937“The work of setting wall bearing steel bar joistscomes under the jurisdiction of the International Associ-ation of Bridge Structural and Ornamental Iron Work-ers.”Erection of EconomizersDECISION RENDERED SEPTEMBER 20, 1937“The decision of the Joint Conference Board ofChicago is affirmed and the decision of the ExecutiveCouncil of the American Federation of Labor is held tobe in force. That decision reads as follows:“In the controversy existing between the Brotherhoodof Boiler Makers and the United Association ofPlumbers and Steam Fitters over the erection of econo-mizers, the decision is that in the opinion of the Execu-tive Council the work belongs to the United Associationof Plumbers and Steam Fitters.”Jurisdiction Over Lock Gates and Flood GatesDECISION RENDERED OCTOBER 21, 1937“The decision of President Williams is affirmed. Thesubject-matter of lock gates and flood gates is not cov-ered by the agreement between the Boiler Makers andIron Workers and the dispute in question is subject to ar-bitration section of the agreement as follows:
142“Section 7. Any further disputes that may arise be-tween the parties of this agreement shall be first consid-ered by the respective General Presidents. Upon theirfailure to agree, the question shall be submitted to arbi-tration. None of the work definitely decided upon in thisagreement shall be subject to further arbitration.”Jurisdiction Over Operating of Electric Genera-tors for Welding PurposesDECISION RENDERED OCTOBER 25, 1937The Decision of the Referee is that the binding na-tional decisions of the American Federation of Labor,the Building and Construction Trades Department of theAmerican Federation of Labor and the National Board ofJurisdictional Awards cover the operation of electricalwelding apparatus and that such operation is incident tothe trade doing the welding. The decision of the NewarkCommittee on Jurisdictional Disputes is overruled andthe jurisdictional right to operate electric welding sets isheld to be, by existing decisions, within the jurisdictionof the trade doing the welding.Pointing and Caulking of Steel Window FramesWhen Incased in Brick WallsDECISION RENDERED NOVEMBER 18, 1937The decision of the St. Joseph, Mo., Joint ArbitrationBoard awarding jurisdiction over the pointing and caulk-ing of steel window frames, when encased in brick walls,to the International Association of Bridge and StructuralIron Workers is reversed and such work, when donewith mortar or plastic materials of any kind is held to bewithin the jurisdiction of the Bricklayers, Masons andPlasterers’ International Union of America.
143Decision of the Referee on the Interpretation ofthe Agreements Between the Bricklayers, Ma-sons and Plasterers’ International Union ofAmerica and the Operative Plasters and CementFinishers’ International Union of America Relat-ing to Artificial Stone and Marble and AcousticalTile.DECEMBER 20, 1937The Referee decides that the installation of the mate-rial in question on the Library of Congress Annex comesunder the 1929 agreement and is, therefore, under theterms of the agreement, within the jurisdiction of theBricklayers, Masons and Plasterers’ International Unionof America. The material is in no real sense, except in itsacoustical properties, similar to the acoustical tile whichwas the subject of the 1930 agreement. There may beborder line cases between the two types of material cov-ered in the agreements of 1929 and 1930 but this materialis not one of them. It is clearly on the side of artificialstone, rather than on the side of materials similar toacoustical tile or, particularly, the U. S. Gypsum productknown as Acoustone. Moreover, its installation followsthe craft method used by the Bricklayers, Masons andPlasterers’ International Union.This decision applies only to the interpretation of theagreement between the Bricklayers and Operative Plas-terers’ Unions.(Signed) JOHN A. LAPP, Referee
144Jurisdiction Over the Unloading of Ready MixedConcrete from Certain Types of Trucks to theGround on Building and Construction Jobs.DECISION RENDERED JANUARY 17, 1938The referee decides that the unloading of ready mixedconcrete from trucks to a building or construction job,by means of machinery, attached to the truck, that re-moves the concrete from the bin of the truck, and theoperation of the motor or piece of machinery used in un-loading, is the work of the International Brotherhood ofTeamsters, Chauffeurs, Stablemen and Helpers of Amer-ica.Decision of the Referee on the Question of Dryingand Handling Sludge at the Southwest SewageTreatment Works in Chicago.MAY 2, 1938THE DECISIONThe erection of the process, piping, ducts and equip-ment for the drying and handling of sludge at theSouthwest Sewage Treatment Works at Chicago iswithin the jurisdiction of the International Brother-hood of Boiler Makers and Iron Ship Builders andHelpers of America.Memorandum to the Decision on the Drying andHandling of Sludge at the Southwest SewageTreatment Works in Chicago.MAY 25, 1938This decision is limited to the fabricated steel ducts,through which sludge passes in the drying process, asexplained in the opinion accompanying the decision. It
145does not apply to the piping of coal, which was specifi-cally withdrawn from the complaint, nor does it apply tothe equipment between the furnace and the pre-heateror between the pre-heater and the roof. It does not applyto any other portion of the equipment which is regularlyin the jurisdiction of any other International Buildingand Construction Trades Union.(Signed) JOHN A. LAPP, Referee,Building and Construction Trades Dept.,American Federation of Labor.Decision in the Matter of Setting of Vitrolite andSimilar Forms of Structural GlassJUNE 14, 1938THE DECISIONThe Referee finds and decides that the setting of vitro-lite and similar structural glass on inside work belongswithin the jurisdiction of the Bricklayers, Masons andPlasterers’ International Union of America, except whensuch structural glass is set in panels, sash, frames ormouldings or with toggle bolts, screws, rosettes or simi-lar fastenings, or secured in some other manner com-mon to the work of the Glaziers. The Referee finds anddecides that vitrolite and similar structural glass, whenset on outside walls of buildings or structures, in mortar,cement or plastic material or when anchored to the wallin the manner common to the trade of the Marble Setter,belongs within the jurisdiction of the Bricklayers, Ma-sons and Plasterers’ International Union of America.The Referee finds and decides that all outside workaround windows and entrances in store and office frontsopening on streets, arcades, corridors or other public
146places, including columns at such entrances, belongs tothe Brotherhood of Painters, Decorators and Paperhang-ers of America. The above shall include substantial bor-ders not exceeding three feet around such windows andentrances. Other outside installation of structural glasson exterior walls belongs to the Brotherhood ofPainters, Decorators and Paperhangers of America, if seton one or more sides in panels, frames or mouldings orwith metal or other strips used to support it or if securedwith toggle bolts, screws or similar fastenings, despitethe additional use of any form of plastic or mastic com-position.The installation of structural glass, when used asbackground for store and office signs and advertising, iswithin the jurisdiction of the Brotherhood of Painters,Decorators and Paperhangers of America.When glass is used of a thickness of more than one-half inch, its installation belongs within the jurisdictionof the Bricklayers, Masons and Plasterers’ InternationalUnion of America, unless it is set in sash frames, doorsor skylights in a manner similar to that used byGlaziers.Wherever at this time any local agreement existswhich is affected in any way by this decision, the effec-tive date of this decision shall be in such cases threemonths from this date or September 14, 1938, otherwisethe decision is effective as of this date.The Referee is aware of the fact that there are manyvariations in the installation of structural glass and thatsome specific cases may not be covered by this decision.He believes that the International Officers of the twoUnions involved can readily find a solution for any spe-cific application on the basis of the broad principles laid
147down in this decision and he suggests that on the basisof this decision, provision be made that any dispute overits application be referred for interpretation to the Ref-eree or some other impartial agency.Jurisdiction Over the Assembling and Erection ofCertain Meal Bins, Grit Bins and Grain Bins in theEichler Brewery, New York City.October 31, 1938THE DECISIONThe decision of the Building Trades Employers’ Asso-ciation of the City of New York, granting jurisdictionover the erection of grain storage bins in the EichlerBrewery to the International Association of Bridge,Structural and Ornamental Iron Workers is overruledand the dispute is declared to be one which must be sub-mitted to arbitration according to the provisions of Sec-tion 7 of the agreement between the International Broth-erhood of Boiler Makers, Iron Ship Builders and Helpersand the International Association of Bridge, Structuraland Ornamental Iron Workers.(Signed) JOHN A. LAPP, Referee.DECISION RENDERED BY PETER ELLER, NA-TIONAL REFEREE IN DISPUTE OVER ASPHALTAND RUBBER TILE, ROLL AND SHEETLINOLEUM.July 6, 1942.United Brotherhood of Carpenters and Joiners ofAmerica.Brotherhood of Painters, Decorators and Paper Hang-ers.
148United Slate, Tile, and Composition Roofers, Dampand Waterproof Workers’ Association.Bricklayers, Masons and Plasterers’ InternationalUnion.Operative Plasterers and Cement Finishers’ Interna-tional Union.In addition, briefs setting forth the claims of the re-spective organizations were also sent to the Referee.After due and careful consideration, it is the decisionof the Referee that the jurisdiction of the work in ques-tion be divided between the United Brotherhood of Car-penters and Joiners, and the Brotherhood of Painters onthe following basis:To the Brotherhood of Painters, Kansas City, Missouriand all territory to the Westward.To the United Brotherhood of Carpenters and Joiners,all territory East of Kansas City.In connection with the decision above stated, the fol-lowing recommendations are made:1. That members of the Tile Setters affiliated with theB. M. P. I. U., and the Cement Finishers affiliatedwith the O. P. C. F. I. A. capable of doing this workbe taken into either or both the organizations abovementioned without payment of initiation fee andwithout losing their membership in their own organ-izations, somewhat on the basis of the agreementnow existing between O. P. C. F. I. A. and B. M. P. I.U. relative to the exchange of cards in connectionwith plastering.2. On account of the prolonged controversy over thework in question, it is suggested that this decision
149be not made effective for three (3) months so as topermit of any necessary adjustments on existingcontracts.3. This decision deals solely with the material men-tioned above when used on floors and characterizedas “resilient floors” or “resilient floor coverings.” Itdoes not cover roofing nor the application of thesematerials to walls.P. W. ELLER,National Referee.
150DECISIONS RENDERED BY NATIONAL REFEREEWILLIAM L. HUTCHESON.Decision by the National Referee of the Buildingand Construction Trades Department, William L.Hutcheson, in the jurisdictional dispute betweenInternational Hod Carriers, Building and Com-mon Laborers Union of America and United Asso-ciation of Journeymen Plumbers and Steamfit-ters of the United States and Canada in the mat-ter of installation of non-metallic piping for sew-ers.The following is a resume, conclusions and findings bythe National Referee for the Building and ConstructionTrades Department, in the case of the jurisdictional dis-pute between the International Hod Carriers, Buildingand Common Laborers’ Union of America and theUnited Association of Journeymen Plumbers and Steam-fitters of the United States and Canada, in the matter of:installation of non-metallic pipe for sewers.The hearing was called to order, by the Referee, onMonday, October 8, 1945, at 10 a. m., in the NetherlandPlaza Hotel, Cincinnati, Ohio.Present at the hearing were representatives of the HodCarriers and Common Laborers’ Union; Plumbers andSteamfitters; Bricklayers International Union and theBrotherhood of Teamsters.Representatives of the Hod Carriers and Common La-borers’ submitted preliminary objections to the Refereehaving jurisdiction in the dispute.Their objections were primarily based on the con-tention that there was in existence an agreement be-tween the Hod Carriers, Building and Common Labor-
151ers’ Union and the United Association of JourneymenPlumbers and Steamfitters, and in substantiation of theircontention they submitted an agreement as of the date,January 23, 1941, between the two organizations.In their remarks in reference to their preliminary ob-jections the statement was made by representatives ofthe Hod Carriers and Common Laborers’ that they wereready to meet any of the trades that have any claim towork covered in the agreement.Representatives of the United Association ofPlumbers and Steamfitters replied to the objectionraised by representatives of the Hod Carriers and Com-mon Laborers’ but state that they recognized the agree-ment as of January 23, 1941.After hearing both parties present their views in refer-ence to the agreement, and listening to considerable dis-cussion, the Referee stated that he was placed in the po-sition of having to make a ruling on the agreement as ofJanuary 23, 1941, and ruled that said agreement was abona fide agreement, without any interpretation of themeaning thereof, and should stand as an agreement be-tween the two organizations; with the understandingthat there should be no infringement upon the jurisdic-tion of other organizations.After the above ruling was made the two contestingparties were asked to arrange to meet and see if somemutual understanding could be arrived at, after whichthe hearing was adjourned at 11:30 a. m. (October 8)until the next morning at 10 a. m .The hearing was reconvened on Tuesday, October 9, at10 a. m.A report was asked for by the Referee as to what, if
152any, progress was made in reference to reaching an un-derstanding, and it was stated that no understandingwas reached.The Referee then stated that while it was permissiblefor the two organizations to enter into an agreement,such as was reached January 23, 1941, inasmuch as nounderstanding was reached yesterday afternoon in theconference that was held by representatives of the twoorganizations, he would rule that the case which was re-ferred to him by the Acting President of the Building andConstruction Trades Department in May, 1944, would beheard as per that arrangement.A representative of the Hod Carriers then asked if thedispute before the Referee was covered by the agreement.The Referee, in reply to that question, stated that untilhe heard the evidence he would not be able to determinewhether it came under the agreement, or whether it didnot, and that he would reach that conclusion after hehad heard the evidence.A representative of the Hod Carriers and Common La-borers’ then stated, if a hearing was going to be held onthe merits of the case they were in the unfortunate posi-tion of being unable to participate, for the reasons: thatthe agreement itself is self-explanatory to some degree,and in order to clarify it more, the respective Interna-tional Presidents of the disputant parties appointed com-mittees for the purpose of clarification, and when theyreached an interpretation they sent a letter to the respec-tive International Presidents, which letter they statedthey wished to read.Objections were raised by representatives of thePlumbers which brought forth a discussion as betweenthey and representatives of the Hod Carriers and Common
153Laborers’ after which the Referee stated that he wouldallow the letter to be read and then determine whether itwould go into the record, or whether it would not.After the letter was read the Referee asked what thepurpose for reading it was, and was answered by a rep-resentative of the Hod Carriers and Common Laborers’that the purpose in reading the communication was toshow that the interpretation arrived at by the committeewas in good faith.The Referee then ruled that in the original agreementno reference was made in regards to appointing a com-mittee to interpret the meaning thereof, and furtherruled that the letter would not appear in the record.After some discussion and statements by representativesof the two organizations, during which reference was madeto a decision rendered by Acting President of the Buildingand Construction Trades Department, representatives ofthe Hod Carriers and Common Laborers’ asked to be ex-cused on the grounds that participation by them in thehearing on the merits of the case would constitute a waiverof their rights, with leave to appeal the matter further.In the discussion they were asked if they wished to ap-peal. They stated: With leave to appeal the matter fur-ther. They were informed that it was up to them to fol-low the laws of the Department and the Federation inas-much as the Referee had no authority to say whetherthey had a right to appeal or whether they did not.Representatives of the Hod Carriers and Common La-borers’ further contended if they anticipated that theywould waive their rights as the work in contention wascovered by the agreement which had been recognized, andinasmuch as they had other tribunals to go to they inter-jected the last request that they be given leave to appeal.
154A discussion (off the record) was had at this point,when it was again asked by one of the representatives ofthe Hod Carriers that his point be made a part of therecord. Asked to repeat his statement, he stated, theywere unable to participate in the case on its merits. Hewas asked if he wanted to use the word “unable” or “un-willing.” He replied, we are placed in the position ofbeing unable to participate in the hearing by reason ofthe fact that it would constitute a waiver of our rights, inthe absence of a ruling by the Referee as to whether thedispute was covered by the agreement.They were informed by the Referee that it would be a partof the record as to why they were not going to participate.The Plumbers then proceeded to present evidence tosubstantiate their claim for work, as per the decision ofActing President Gray.They presented extensive briefs and evidence to sub-stantiate their claim, consisting of numerous exhibits andillustrations of installations of the work in contention.After they completed presentations of their evidencethe matter was reported to the Executive Council of theBuilding and Construction Trades Department for con-sideration, and action, for the benefit and information ofthe Referee as to what the desires of the Council were inreference to making a finding and decision, because ofthe Hod Carriers and Common Laborers’ withdrawingfrom the hearing; after which the Executive Counciltook the following action:“Action of Council: Referee should proceed and ren-der decision in accordance with Section 7, Page 26 ofConstitution of Department.“Vote: Unanimous. V. P. Hutcheson not voting.”
155Pursuant to the foregoing action of the ExecutiveCouncil, and after reviewing the evidence, I havereached the following conclusion:That the agreement as referred to between the Interna-tional Hod Carriers, Building and Common Laborers’Union of America and the United Association of Journey-men Plumbers and Steamfitters of the United States andCanada, covers work on subways, tunnels, highways,viaducts, streets and roadways in connection with sewersand water mains, and therefore, does not apply to the ques-tion at issue, which is, the decision rendered by the ActingPresident of the Building and Construction Trades Depart-ment, Richard J. Gray, which was rendered under date ofMarch 13, 1944, in the dispute between Laborers andPlumbers over the laying of sewer pipe from main sewerinto dwelling, or from inside property line to dwelling, andis not in any way referred to by the agreement of January23, 1941, entered into between the two organizations.Records show that the request for a decision came to theActing President in the regular manner, and that he ren-dered his finding on the date of March 13, 1944, and in re-ferring to the matter stated it was a jurisdictional disputebetween Laborers’ and members of the JourneymenPlumbers and Steamfitters over the laying of lateral sewerpipe from main sewer into dwelling or from inside propertyline to dwelling, and the following decision was rendered:“DECISION”The work in dispute shall be done by members of theUnited Association of Journeymen Plumbers and SteamFitters.In the opinion of the undersigned, acting as Referee,the decision rendered by Acting President Gray, was in
156conformity with the evidence submitted to me as Ref-eree, and in no way comes under the agreement enteredinto between the two contending organizations as ofJanuary 23, 1941.Therefore my decision is as follows:October 13, 1945.1. That the agreement, dated January 23, 1941, be-tween the International Hod Carriers, Building and Com-mon Laborers’ Union of America and the United Associ-ation of Journeymen Plumbers and Steamfitters of theUnited States and Canada is a bona fide agreement be-tween the two organizations, but should not be acceptedby the Department until clarifying language is insertedtherein giving to the Bricklayers’ International organiza-tion jurisdiction over work on sewers which they haveheretofore performed.Also that there should be a clarification in reference tothe unloading and distributing of pipe so that therewould be no infringement upon the recognized jurisdic-tion of the Teamsters International organization.There should also be a further clarification if any otherorganization presents evidence to show that the agree-ment infringes upon their jurisdiction.2. That the laying of lateral sewer pipe from mainsewer into dwelling, or from inside property line todwelling is work that should be done by, or under the su-pervision of, members of the United Association ofJourneymen Plumbers and Steamfitters of the UnitedStates and Canada.WM. L. HUTCHESON (Signed)National Referee,Building and Construction Trades Department
157(NOTE—This in no way deletes or expunges fromthe records of this Department the letter of March 9,1946, addressed to the Morris County, New Jersey,Building and Construction Trades Council or the ad-vice contained in Vice President Hutcheson’s telegramof March 27, 1946.)Pointing, Taping and Filling of Joints on WallBoardMay 19, 1947.Mr. Richard J. Gray, PresidentBuilding and Construction Trades Department501 A.F. of L. Building,Washington 1, D.C.Dear Sir and Brother:In the matter of the jurisdictional controversy over thepointing, taping and filling of joints on wallboard inpreparing it to receive paint and other wall coverings, in-volving the Brotherhood of Painters, Decorators and Pa-perhangers of America; Bricklayers, Masons and Plaster-ers International Union of America and the OperativePlasterers and Cement Finishers International Associa-tion of the United States and Canada, a hearing was heldin the Executive Council room, American Federation ofLabor building, May 6, 1947.Representing the organizations involved were: Harry C.Bates, President of the B. M. and P. I. U. of A.; John E.Rooney, President of the O. P. and C. F. I. A.; L. P. Lindelof,General President, B. of P. D. and P. of A.; Joseph P.Hillock, Painters, Washington, D. C.; J. C. Moenick, Secre-tary-Treasurer, Painters District Council, Chicago, Ill.; Mil-ton R. Stephens, Plasterers, Washington, D. C., and WalterRedmond, International Secretary of the O. P. and C. F. I. A.
158After giving the statements made, and evidence sub-mitted, careful consideration I have reached a conclu-sion and render the following decision; to wit:When plaster material is used to do pointing and fillingit shall be the work of members of the Operative Plaster-ers and Cement Finishers International Association ofthe United States and Canada—and/or—members of theBricklayers, Masons and Plasterers International Unionof America.When adhesive materials are used it shall be the workof members of the Brotherhood of Painters, Decoratorsand Paperhangers of America.Respectfully submitted,WM. L. HUTCHESON (Signed)Referee,Building and Construction Trades Department.Sitting with Referee at hearing were: Vice PresidentsWm. J. McSorley and Robert Byron of the Building andConstruction Traders Department.
159Erection of Catwalks and StairwaysMay 19, 1947.Mr. Richard J. Gray, PresidentBuilding and Construction Trades Department501 A. F. L. BuildingWashington 1, D. C.Dear Sir and Brother:In the matter of the jurisdictional controversy over theerection of catwalks and stairways involving the Interna-tional Association of Bridge, Structural and OrnamentalIron Workers and the International Brotherhood of Boil-ermakers, Iron Ship Builders and Helpers of America, ahearing was held in the Executive Council room, Ameri-can Federation of Labor building, May 8, 1947.Representing the organizations involved were: P. J.Morrin, General President; J. H. Lyons, General Secre-tary; J. J. Dempsey, General Treasurer, International As-sociation of Bridge, Structural and Ornamental IronWorkers; also Clyde F. Strickland, Vice President andLeslie L. Myers, Washington, for the Iron Workers and J.V. Kearney, International Vice President and T. L. Wants,Special Representative, International Brotherhood ofBoilermakers, Iron Ship Builders and Helpers of Amer-ica.Representatives of the two Internationals appearedbefore the undersigned, as Referee, and submitted briefsand evidence to substantiate their claims, and amongother things presented an agreement entered into be-tween the two organizations in 1928. Their attention wascalled to the provisions of Sections 37 and 38 of the Con-stitution of the Building and Construction Trades De-partment which set forth:
160“Nothing in Sections 37 and 38 is to be construed asgiving any organization the right to re-open any caselisted by the Building and Construction Trades Depart-ment and published in the records of the Department.”After their briefs were presented a full discussion washeld in reference to the matter and it is the opinion andconclusion of the undersigned that the decision ren-dered by the President of the Department under date ofJanuary 27, 1947, would seem to be as clear a clarifica-tion of their agreement in reference to the erection ofcatwalks and stairways as could be arrived at under thewording of the agreement, and I herewith quote the deci-sion of the President of the Building and ConstructionTrades Department as of January 27, 1947.“Where catwalks, ladders and stairways are erectedin connection with bubble towers and tanks and are at-tached to the structural steel supports this work shallbe the work of the members of the International Associ-ation of Bridge, Structural and Ornamental Iron Work-ers.“Where such catwalks, ladders and stairways are riv-eted or welded to the watertight sections of the bubbletowers or tanks this work shall be done by the membersof the International Brotherhood of Boilermakers, IronShip Builders and Helpers.”Respectfully submittedWM. L. HUTCHESON (Signed)Referee,Building and Construction Trades Department.Sitting with Referee at the hearing were: Vice PresidentsWm. J. McSorley and Martin P. Durkin of the Buildingand Construction Trades Department.
161Q-PanelsMay 19, 1947.Mr. Richard J. Gray, PresidentBuilding and Construction Trades Department501 A. F. of L. Building,Washington 1, D. C.Dear Sir and Brother:In the matter of the jurisdictional controversy over theerection of aluminum Q-panels involving the Sheet MetalWorkers International Association and the InternationalAssociation of Bridge, Structural and Ornamental IronWorkers, a hearing was held in the Executive Councilroom, American Federation of Labor building, May 7,1947.Representing the organizations involved were P. J.Morrin, General President; J. H. Lyons, General Secre-tary and J. J. Dempsey, General Treasurer, InternationalAssociation of Bridge, Structural and Ornamental IronWorkers; Glenn Hurley, Superintendent, H. H. RobertsonCompany; George Bigelow, Manager of Erection, H. H.Robertson Company, and George L. Illig, Contract De-partment, H. H. Robertson Company, and Robert Byron,General President, Sheet Metal Workers InternationalAssociation and Joseph Fredericks, Sheet Metal Work-ers International Association.At the hearing held, briefs were submitted and state-ments made by the contesting parties, as well as a dis-play of the material in question.In the statements made by representatives of the twoInternationals, considerable emphasis was made in ref-erence to decisions rendered some years ago giving tothe Sheet Metal Workers jurisdiction over the installa-
162tion of metal of ten gauge or lighter, but the question be-fore the Referee in this case was the installation of Q-panels.After giving the evidence as submitted due considera-tion I am of the opinion that:The erection of Q-panels, which was the point at issue,when fastened to the steel structure of a building, shouldbe the work of members of the International Associationof Bridge, Structural and Ornamental Iron Workers.However, any flashing or ventilator work in connec-tion therewith should be the work of the members of theSheet Metal Workers International Association.Respectfully submitted,WM. L. HUTCHESON (Signed)Referee,Building and Construction Trades DepartmentSitting with Referee at the hearing were: Vice PresidentsWm. J. McSorley and Martin P. Durkin of the Buildingand Construction Trades Department.Robertson Protected MetalMay 19, 1947Mr. Richard J. Gray, PresidentBuilding and Construction Trades Department501 A. F. of L. Building,Washington 1, D. C.Dear Sir and Brother:In the matter of the jurisdictional controversy over theerection of Robertson Protected Metal involving theSheet Metal Workers International Association and theInternational Association of Bridge, Structural and Orna-
163mental Iron Workers, a hearing was held in the Execu-tive Council room, American Federation of Labor build-ing, May 7, 1947.Representing the organizations involved were P. J.Morrin, General President; J. H. Lyons, General Secre-tary and J. J. Dempsey, General Treasurer, InternationalAssociation of Bridge, Structural and Ornamental IronWorkers; George Bigelow, Manager of Erection, H. H.Robertson Company, and Robert Byron, General Presi-dent, Sheet Metal Workers International Association,and Joseph Fredericks, Sheet Metal Workers Interna-tional Association.When this case came on for hearing on the question oferection of Robertson Protected Metal, in presentingtheir briefs and evidence, the two contestants both re-ferred to a ruling or decision rendered under date of May26, 1923, by the former Board of Jurisdictional Awards,and while it was admitted by representatives of both In-ternational organizations that the ruling made as abovereferred to; namely May 26, 1923, has been recognizedand published in the records of the Building and Con-struction Trades Department, attention was also calledto Paragraph 5, Section 38 of the Constitution of theBuilding and Construction Trades Department whichsets forth:“Nothing in Sections 37 and 38 is to be construed asgiving any organization the right to reopen any caselisted by the Building and Construction Trades Depart-ment and published in the records of the Department.”Under that provision I can only reach the conclusionthat as Referee I would have no right to render a definitedecision in the case at issue.If the two contesting International organizations de-
164sire a clarification of the action taken by the formerBoard of Jurisdictional Awards under date of May 26,1923, they could by joint request ask for such interpreta-tion or clarification.Respectfully submittedWM. L. HUTCHESON (Signed)Referee,Building and Construction Trades Department.Sitting with Referee at the hearing were: Vice PresidentsWm. J. McSorley and Martin P. Durkin of the Buildingand Construction Trades Department.
165DECISIONS OF NATIONAL JOINT BOARD FORSETTLEMENT OF JURISDICTIONAL DIS-PUTES, BUILDING AND CONSTRUCTION IN-DUSTRY & HEARINGS PANELS.DECISION OF JOINT BOARD NO. 3Beer Lines, Wort Lines, Yeast Lines, CO2Lines, and Refrigeration in ConnectionWith Attemperator TanksAUGUST 20, 1948Dispute between the United Association of Journey-men and Apprentices of the Plumbing and Pipe FittingIndustry of the United States and Canada and the SheetMetal Workers’ International Association.The issue in dispute is the installation of copper pipingin breweries for beer lines, wort lines, yeast lines, CO2lines, and refrigeration in connection with attemperatortanks.After carefully considering all of the evidence and ar-gument as presented by both sides, the Joint Board de-cides as follows:The installation of streamlined or other manufacturedcopper pipe or fittings for beer lines, wort lines, yeastlines, CO2lines is the work of the United Association ofJourneymen and Apprentices of the Plumbing and PipeFittings Industry of the United States and Canada. Theinstallation of copper attemperator coils in the interiorof tanks and vats in breweries is the work of the Copper-smiths, members of the Sheet Metal Workers’ Interna-tional Association.
166The decision of the Joint Board is unanimous.WM. J. MCSORLEY,HARRY C. BATES,ARTHUR H. WELLS,A. HERRMANN WILSON,JOHN T. DUNLOP,Chairman.DECISION OF JOINT BOARD NO. 15Steel Decking, Roofing, Flooring, Raceway forElectrical WiringAUGUST 21, 1948Dispute between the Sheet Metal Workers Interna-tional Association and the International Association ofBridge, Structural and Ornamental Iron Workers.The issue in dispute is that involved in cases 15 and 22.The Joint Board may consider the whole issue of the in-stallation of steel decking in accordance with the agree-ment between the two unions.After carefully considering all of the evidence and ar-gument as presented by both sides, and two interveningorganizations, the Joint Board decides as follows:The installation of steel decking for roofing, if 10gauge or lighter, is the work of the Sheet Metal WorkersInternational Association. The installation of steel deck-ing for flooring is the work of the International Associa-tion of Bridge, Structural and Ornamental Iron Workers.This decision cannot alter previous decisions of record,such as January 26, 1928 (Holorib), May 19, 1947 (Q-Panel), June 3, 1948 (Metro-Deck). Whenever steel deck-ing for flooring or roofing is used as a raceway for elec-trical wiring the electrical work in connection with the
167raceway is that of the International Brotherhood of Elec-trical Workers.The decision of the Joint Board is unanimous.WM. E. MALONEY,L. P. LINDELOF,ARTHUR H. WELLS,ALBERT BEEVER,JOHN T. DUNLOP,Chairman.JOINT BOARD NO. 2Pre-Heating and Stress Relieving of WeldsSEPTEMBER 22, 1948Dispute between the United Association of Journey-men and Apprentices of the Plumbing and Pipe FittingIndustry of the United States and Canada and the Inter-national Brotherhood of Electrical Workers.The issue in dispute is the pre-heating and stress re-lieving of welds.After carefully considering all of the evidence and ar-gument as presented by both sides the Joint Board de-cides as follows:The installation of induction pre-heating and stress re-lieving equipment, including the wrapping of coils, is thework of the International Brotherhood of ElectricalWorkers.The installation of manufactured resistance coils shallbe the work of the United Association of Journeymenand Apprentices of the Plumbing and Pipe Fitting Indus-try.
168The operation of the pre-heating and stress relievingequipment and instruments for pipe welding is the workof the United Association of Journeymen and Appren-tices of the Plumbing and Pipe Fitting Industry.The decision of the Joint Board is unanimous.WM. J. MCSORLEY,L. P. LINDELOF,ARTHUR H. WELLS,C. J. ESBENSHADE,JOHN T. DUNLOP,Chairman.CLARIFICATION BY JOINT BOARD NO. 2FEBRUARY 28, 1949Board of Trustees,National Joint Board for Settlement ofJurisdictional Disputes,901 Massachusetts Avenue, N. W.,Washington 1, D. C.Re: JOINT BOARD NO. 2Dear Sirs:Joint Board No. 2 has carefully considered the issuesraised by correspondence from the United Associationof Journeymen and Apprentices of the Plumbing andPipe Fitting Industry and the International Brotherhoodof Electrical Workers concerning our decision of Sep-tember 22, 1948, as directed by the Board of Trustees ofJanuary 11, 1949.The Joint Board finds that the issues now referred toit concerns the unwrapping of induction coils, the han-dling and moving of the equipment including the sec-ondary cable leads, the installation of water cooled
169coils and the wrapping of resistance coils—as distin-guished from the installation of manufactured resist-ance coils.The Joint Board has reviewed the full record of itsproceedings, and the recent letters from the two organi-zations, and has unanimously concluded that these is-sues are covered by paragraph one of its decision.Very truly yours,(Signed) WM. J. MCSORLEY,L. P. LINDELOF,ARTHUR H. WELLS,C. J. ESBENSHADE,JOHN T. DUNLOP,Chairman.DECISION OF JOINT BOARD NO. 17Operation of Gasoline Driven Electric Generatorsfor WeldingOCTOBER 27, 1948In the dispute between the United Association of Jour-neymen and Apprentices of the Plumbing and Pipe Fit-ting Industry of the United States and Canada and the In-ternational Union of Operating Engineers.The issue in dispute is the operation of gasoline drivenelectric generators for welding.After consideration of the evidence and argument ad-vanced by all parties, the Joint Board decides that thework in dispute is covered by Resolution 124 (AmericanFederation of Labor, Norfolk Convention) and is the ju-risdiction of the International Union of Operating Engi-neers.
170The decision of the Joint Board is unanimous.JOHN E. ROONEY,L. P. LINDELOF,FRANK W. BARNES,CYRIL J. STATT,JOHN T. DUNLOP,Chairman.ASH HOPPERS AND FURNACE BOTTOMSOCTOBER 6, 1950The dispute referred to the Hearings Panel, which heldits hearing in Washington, D.C., on August 29, 1950, is de-cided as follows:The installation of ash hoppers is within the jurisdic-tion of the Iron Worker; the installation of furnace bot-toms is within the jurisdiction of the Boilermakers.For the purposes of providing a line of demarcationbetween furnace bottoms and ash hoppers for the pur-pose of determining the jurisdiction of work betweenthe two trades:(a) A furnace bottom shall be defined as that bottompart of the furnace or chamber subject to directand continuous exposure to the fire in the furnacethat is air and/or water tight.(b) An ash hopper is any container for ash which isnot subject to direct and continuous exposure tothe fire in the furnace whether or not air or watertight.As stated in the minutes of the hearing of August 29,1950, the above decision does not affect the recognizedjurisdiction of the United Association of Journeymenand Apprentices of the Plumbing and Pipe Fitting Indus-
171try of the United States and Canada, United Brotherhoodof Carpenters and Joiners of America, Sheet Metal Work-ers International Association, International Union of Op-erating Engineers, and the Bricklayers, Masons and Plas-terers’ International Union of America as stipulated onthe record by both the Iron Workers and Boilermakersduring the hearing.(Signed) HARRY C. BATES,CHARLES AQUADRO,JOHN T. DUNLOP.INSTALLATION OF CEILING SYSTEMSJANUARY 15, 1968This dispute, which was referred by the National JointBoard on November 23, 1965, was the subject of hear-ings before the Hearings Panel in Washington, D. C.,March 4, 1966, and May 16 and 17, 1966. The decision ofthe Hearings Panel was issued August 24, 1966, but wasstayed because of court litigation until January 15, 1968.The decision of the Hearings Panel, which was upheldby decisions of the U. S. District Court for the District ofColumbia, the U. S. Court of Appeals for the District ofColumbia Circuit and the Supreme Court of the UnitedStates, is as follows:1. The decision of this Hearings Panel is limited tothe jurisdictional disputes or work assignments in con-troversy between lathers and carpenters involved inthe installation of ceiling systems. Nothing in this deci-sion shall affect the jurisdiction or work assignment ofany other trade, such as, but not limited to, the sheetmetal workers, electricians, iron workers, etc., with aclaim or interest in the installation of ceiling systems.Contractors shall use this decision as a basis for mak-
172ing work assignments only with regard to work in theinstallation of ceiling systems involving carpenters andlathers.2. The installation of gypsum wallboard and othertypes of panels fastened directly to ceiling joists shallbe performed by carpenters. In the event that a carry-ing channel is used with gypsum wallboard or othertypes of panels attached thereto, notwithstandingparagraph 4(a) below, the contractor may use carpen-ters to install the carrying channel in areas not exceed-ing 300 square feet where there are no lathers on thejob.3. The installation of light iron work in ceiling sys-tems with gypsum, Portland cement, acoustical or otherplasters sprayed-on or trowel-applied over lath or di-rectly to structural members shall be performed by lath-ers.4. The following types of ceiling systems are includedin this paragraph: Direct Hung Suspension Systems; At-tached Concealed System without Backing Board; Fur-ring Bar Attached System; Furring Bar Suspension Sys-tem; Indirect Hung Suspension System or similar sys-tems.(a) The installation of the 1¹⁄₂" channel or similar car-rying channel and hangers in any of the above types ofsystems shall be performed by lathers.(b) The installation of all other work, including the in-stallation of a ceiling system in its entirety if no 1¹⁄₂"channel or other carrying channel is used, shall be per-formed by carpenters.
1735. This decision shall be effective on all work assign-ments made on construction contracts let after January15, 1968.HEARINGS PANELPETER T. SCHOEMANN (Signed)HUNTER P. W HARTONWM. E. NAUMANNED. S. TORRENCEJOHN T. DUNLOP(Impartial Umpire)DECISION ON THEPOINTING AND TAPING OF DRYWALLSURFACESMarch 1, 1978The Hearings Panel is aware that a number ofcrafts, including the carpenters and the laborers, havea genuine interest in issues defined as broadly asthose referred to the Hearings Panel by the July 15,1976 letter of the Joint Administrative Committee. Sodo their employers. However, in order to facilitate thisproceeding, and in order to dispose of the matter pre-sented to us by the Joint Administrative Committee ofthe Plan and the Impartial Jurisdictional DisputesBoard, the Hearings Panel will limit the issue to be de-cided to certain matters (set forth below) in contro-versy between the Painters and the Plasterers(whether represented by the Operative Plasterers andCement Masons International Association or by theInternational Union of Bricklayers and Allied Crafts-men). No action or decision of the Hearings Panel willin any way affect the jurisdiction or work assignmentsinvolving any trade other than the International Broth-
174erhood of Painters and Allied Trades, the OperativePlasterers and Cement Masons International Associa-tion, and the International Union of Bricklayers andAllied Craftsmen. No fourth trade union with a claimor interest in the assignments which have been con-sidered by this Hearings Panel shall be affected in anyway by a decision of this Panel. Any action or decisionof the Hearings Panel shall explicitly contain languagestating that the interest of any other trade shall in noway be affected and that contractors shall use suchdecisions as a basis for making assignments only withregard to assignments involving the painters and theplasterers.The preponderance of the evidence before us sup-ports the resolution of the dispute submitted to us in thefollowing manner:(1) All pointing and taping, regardless of materialused, is painters’ work, provided the drywall sur-faces are not to receive plaster, acoustical or imita-tion acoustical finishes.(2) Pointing and taping, regardless of material used, ofdrywall surfaces which are to receive plaster,acoustical or imitation acoustical finishes shall bethe work of plasterers.(3) The surface produced by the application of thesame plaster pointing material as used in the point-ing and taping of the joints to the entire drywallsurface for the purpose of producing a uniformsurface compatible with the pointed and tapedjoints shall be considered a plaster finish, and thepointing and taping in connection therewith shallbe the work of plasterers.
175This decision shall be effective on all work assign-ments made on or after thirty days from this date.HEARINGS PANELF. JOHN BARLOW (Signed)HAROLD J. BUOYEDWARD J. CARLOUGHWILLIAM E. NAUMANNDANIEL Q. MILLS(Impartial Umpire)
176 Decision on Cement Finishing and Plastering Work Tasks February 11, 2004 and March 11, 2004 After an arduous review of the evidence entered into this arbitration, the Panel finds good and sufficient reason to render the following decision. Henceforth, all jurisdictional disputes between the BAC and the OPCM that are brought before the Plan shall be resolved in favor of the work assignment of the involved Employer. Jurisdictional disputes between the BAC or OPCM and LIUNA, or any other union(s) brought before the Plan shall be resolved under the procedures of Article V of the Plan. On March 2, 2004, the Joint Administrative Committee requested clarification regarding the scope of the work encompassed in all jurisdictional disputes solely between the BAC and the OPCM to be resolved in favor of the work assignment of the involved Employer. Such scope is limited to cement finishing and plastering work tasks. NATIONAL ARBITRATION PANEL Thomas G. Pagan, Chairman (Signed) Andy Douglas (Signed) John McMahon (Signed)
177 INDEX Acetylene and Electric Welding .................................... 115 AGREEMENTS ........................................................ 39-101 Asbestos Workers and Bricklayers ............................ 100 Boiler Makers and Iron Workers ........................... 46, 86 Boiler Makers and Plumbers .................................. 71-72 Bricklayers, Laborers, Plasterers ................................ 83 Bricklayers and Operative Plasterers .......................... 55 Carpenters and Lathers .............................................. 45 Carpenters and Painters ............................................. 39 Carpenters and Plasterers .......................................... 67 Carpenters and Plumbers ........................................... 65 Carpenters and Sheet Metal Workers .......................... 62 Electrical Workers and Laborers ........................... 69, 85 Engineers and Plumbers ............................................. 52 Iron Workers and Elevator Constructors ............... 50, 85 Lathers and Sheet MetalWorkers ................................ 40 Painters and Plasterers ............................................. 43 Sheet Metal Workers and Asbestos Workers ................ 64 Sheet Meal Workers and Boiler Makers ....................... 49 Sheet Metal Workers and Plumbers ............................ 54 Sheet Metal Workers—Roofers ................................... 81 Tilelayers, Bricklayers and Operative Plasterers .............................................................. 59 Teamsters and Electrical Workers .............................. 79 Acoustone (agreement) .................................................. 58 Air Coolers, Air Washers and Blowers, etc. ................... 108 Air Piping in Connection with Elevator Door Locks ...................................................................... 132 Alberene Stone Slabs used as Drain Boards or Backs in Connection with Sinks, Setting of .............. 130 Artificial Stone—Granite (Dressing, Altering and Finishing).......................................................... 128 Artificial Stone—Setting and Installing ........................ 132 Artificial Stone, Decision by Dr. Lapp on Interpretation of Agreement .................................... 143 Asbestos Plaster for Boiler Rooms, etc ......................... 113 Ash Hoppers and Furnace Bottoms .............................. 170 Asphalt and Rubber Tile .............................................. 147 Bathroom Accessories, Anchors for .............................. 122 Bathroom Accessories, Tile and Porcelain .................... 122 Bishopric Board, When Applied as a substitute for Lath and Sheathing ............................................ 124
178 Boilers, Moving, Handling and Placing ......................... 137 Bronzing and Painting of Radiators and Pipe Connections ............................................................ 116 Bush Hammering of Concrete Base Foundation ............ 137 Catwalks and Stairways ............................................... 159 Caulking of Steel Window Frame When Incased in Brick Walls, Pointing and ..................................... 142 Caulking Around Steel Window Sash, Pointing or ........... 81 Ceiling Systems, Installation of ................................... 171 Celotex (Agreement) ...................................................... 45 Cement Finishing and Plastering Work Tasks ............... 176 Concrete Slab Reinforced (Pre-cast) for Roof Tiling ...................................................................... 131 Conduo Base ............................................................... 130 Copper Piping .............................................................. 165 Corrugated Sheeting .................................................... 127 Craftex (Agreement) ....................................................... 43 Cranes, Jurisdiction Over, Operation of Electric and Traveling .......................................................... 134 Cutting Chases or Channels in Brick, Tile, Masonry, etc. ........................................................... 133 Decisions of American Federation of Labor ........... 102-107 Decisions of Hearings Panels ................................ 170-175 Decisions of Referees ............................................ 141-164 Decisions Rendered and Held To Be Operative by the Building and Construction Trades Department ...................................................... 136-140 Decisions by National Joint Board for Settlement of Jurisdictional Disputes ................................. 165-170 Defects in Concrete Caused by Leakage, Bulging, Sagging, etc. ............................................................ 121 Derricks, Erection and Handling for Setting Stone ....... 127 Directional Elevators ..................................................... 85 Drying and Handling of Sludge ..................................... 144 Economizers, Erection of, Decisions of A. F. of L. and Referee ..................................................... 106, 141 Electric Generators for Welding Purposes, Jurisdiction Over Operation ..................................... 142 Electric and Acetylene Welding .................................... 115 Electrical Motors, Setting of ........................................ 136 Electrical Workers—Engineers, Decision of A. F. of L. ................................................................. 99 Electrical Work on Elevators (Rehearing) ..................... 123 Elevator Constructors, International Union, Decision A. F. of L. .................................................. 102
179 Elevator Machinery, Hoisting, Lowering and Placing of ................................................................ 125 Elevators for Hoisting Material, Operation of ............... 127 Engineers Decision of A. F. of L. in re Jurisdiction of ......................................................... 104 Flat-Faced Tile ............................................................ 128 Flaxlinum Keyboard and Insulation ............................. 124 Foremanship Over Concrete Construction ................... 129 Foreman on Interior Concrete Columns, Foundations for Engine and Machinery Beds ............ 123 Furnace Bottoms and Ash Hoppers .............................. 170 Gasoline Driven Elec. Generators ................................. 169 Gates, Jurisdiction Over Lock and Flood ...................... 141 Glazing ........................................................................ 125 Gunnite Work or Handling of Cement Gun ................... 130 Hearings Panel Decision .............................................. 173 Holorib Deck Roofing ................................................... 137 Hi-rib Lath................................................................... 114 Light Iron Furring, Brackets, Clips, Hangers, Corner Guards, Beads and Metallic Lat ..................... 113 Low Pressure Heat ....................................................... 110 Low Pressure Heat (Rehearing) ..................................... 110 Marble and Slate Partitions, Back and Floor Slabs for Urinal Stalls, Closets and Showers, Setting of ................................................................ 118 Meal Bins, etc., Assembling and Erection of ................. 147 Metallic Corner Beads When Set in Plastic Material ................................................................... 115 Metal Windows, Installation of ..................................... 124 Muslin and Canvas for Decorative Purposes, Tacking of ............................................................... 118 Non-Metallic Pipe ........................................................ 150 Pile Driving Machinery and Engines, Operation of ........ 119 Pipe Railings or Guards for Enclosures, Stairway, Hatches, etc. ............................................ 110 Plan for the Settlement of Jurisdictional Disputes ............................................................... 16-38 Article I Scope of Application ................................... 16 Article II Stipulation Requirements .......................... 17 Article III Joint Administrative Committee ............... 18 Article IV Rules and Regulations ............................... 19 Article V Resolution of Jurisdictional Disputes ......... 21 Article VI Continuation of Work ................................ 27 Article VII Enforcement ............................................ 29
180 Article VIII Local Boards ........................................... 31 Article IX Obligations of the Parties .......................... 32 Article X National Arbitration Panel .......................... 33 Article XI Technological Changes .............................. 35 Article XII National Agreements Regarding Jurisdiction ........................................................... 36 Article XIII Effective Date, Termination Change and Withdrawal .......................................... 37 Plaster Board or Substitute Materials Therefor ............. 136 Plastering Work for Preparation of Walls and Ceilings for Tiling .................................................... 131 Pointing or Caulking of Steel Window Frames When Incased in Brick Walls .................................... 142 Pointing and Taping .................................................... 157 Pointing and Taping of Drywall Surfaces ...................... 173 Pointing or Caulking Around Steel Window Sash ............ 81 Power Driven Equipment ............................................. 138 Procedural Rules and Regulations ............................... 1-15 Article I Contractors’ Responsibility ............................ 1 Article II Union’s Responsibility ................................... 2 Article III Strikes and Impediments to Job Progress ..... 3 Article IV Filing a Complaint ........................................ 6 Article V Time Constraints Under the Plan ................... 7 Article VI Direct Resolution ......................................... 8 Article VII Selecting an Arbitrator ................................ 9 Article VIII Resolution by Arbitration ......................... 10 Article IX Policy Regarding Directives ........................ 11 Article X Appeals from Decisions of Recognized Local Boards ........................................ 13 Sample Stipulation Form ........................................... 15 Q-Panels ...................................................................... 161 Reinforced Concrete, Cement and Floor Construction .. 111 Robertson Protected Metal .......................................... 162 Roll and Sheet Linoleum .............................................. 147 Scaffolds as Applied to Building Construction, Erection of .............................................................. 117 Screeds in Cement Construction and Form Work, Setting of ....................................................... 136 Sheet Metal Glazing for Sash, Frames, Doors, Skylights, etc. ......................................................... 119 Slate Treads When Set on Iron Staircase ...................... 120 Spot Grounds, Jurisdiction Over .................................. 136
181 Steel Bar Joists, Setting of Wall Bearing ...................... 141 Steel Decking .............................................................. 166 Steeltex Re-enforcement ............................................. 137 Stress Relieving and Preheating of Welds ..................... 167 Clarification of Above Decision .................................... 168 Teamster-Engineer Decision (Power Equipment) .......... 137 Teamsters and Iron Workers, Decision A. F. of L. ......... 105 Textone (Agreement) ..................................................... 43 Trap Rock Floors by Terrazzo Methods, Placing of Unloading of Ready Mixed Concrete ..................... 133 Unskilled Labor, with Special Reference to the Loading and Unloading of Materials as Applied to Reinforced Concrete Construction ........... 121 Vitrolite and Similar Opaque Glass............................... 112 Vitrolite and Similar Opaque Glass (Rehearing) ............ 112 Vitrolite and Similar forms of Structural Glass ............. 145 Waterproofing, Application of Damp-resisting Preparations and ..................................................... 116 Wood Fibre Conduit (Agreement) .................................... 85