Return to flip book view
NZ OWNED The Genuine M O T S CU Custom Made e d a m RAGE GA Garage Door S R O DO Professionals TM Flush Mounted Doors Custom Made Garage Doors are again leading the market in Christchurch and Nationwide with its Flush Mounted Garage Doors The Flush Mounted Garage Door blends in with the exterior cladding of the architecturally designed home giving it a clean appearance The Garage Door can be clad in contrasting material to match the house whether it be Cedar Alucobond Flat Panel Negative Detail or any other material The Flush Mount finish can be flush between Garage Doors above the doors and at the sides We will work in with the architects on their requirements
NZ OWNED OM CUST Head Detail maRAdGeE GA S R DOO TM Selected cladding system on cavity M O T CUS e d ma E Cavity batten 20mm Maximum 20mm cavity Keep steel angles out as far as possible to reduce the door thickness and weight of the door G A R GA S R O DO Our preference would be to have the outside face of the steel angle flush with the outside face of the cavity batten Exterior 200 250 x 100 x 6mm steel angle Preferred sizes Interior Maximum Door thickness 80mm 80mm 35mm to 40mm Cavity batten on door 30mm Selected cladding system on cavity to door Door frame COPY RIGHTED The drawing shows the cladding on the building protruding down past the steel angle and cavity batten by about 35mm creating a cavity void allowing the door to operate without any interference arcombswith Roadthe steel angle FLUSH MOUNT DOOR HEAD DETAIL Weddons church The gap between the door and cladding on the wall is recommended 03 347 8333 5mm 10mm Both are cut on a 30 degree angle to allow room for the 03 347 8363 door to pull back info custommade co nz te www custommade co nz Reference No A4 Scale 1 2 DRAFT FOR DISCUSSION OM T CUS e mAaRd AGE G ORS DO
NZ OWNED OM CUST madeE G GARA S DOOR Side Jamb Detail TM Selected cladding system on cavity to door Selected cladding system on cavity M O T CUS x 75125 x 6mm angle Preferred125 sizes x 75 xsteel 6mm steel angle e d ma E 10mm Gap G A R GA S R O DO Cavity batten 20mm Exterior Cavity batten on door 30mm Interior Line of rebate below 6mm 4mm Mohair seal Door frame Timber frame Internal lining finishing edge detail to be discussed with designer builder COPY RIGHTED 276 Larcombs Road R D 5 Weddons Christchurch Phone 03 347 8333 Fax 03 347 8363 Email info custommade co nz Website www custommade co nz The drawing shows the wall and door in the same line FOR If you require DRAFT DISCUSSION a Flush Mount look only at the head then the side details would FLUSH MOUNT DOOR JAMB DETAIL change OM UST e C There are variable options in the side details depending on design mAaRd AGE Please contact Custom Made Garage Doors for these details G RS Reference No A4 Scale 1 1 5 DOO
Steel Lintel Jambs OM CUST maRAdGeE Steel Lintel Jambs GA S R O DO 200 250 x 100 x 6mm Angle TM M O T CUS e d ma E G A GAR S R O O D 125 x 75 x 6mm Angle Rebate Line Steel Lintel Jambs COPY RIGHTED DRAFT FOR DISCUSSION Custom Made Garage Doors Ltd FLUSH MOUNT DOOR 3D DETAIL ton Rolles Reference No Phone 03 347 8333 Fax 03 347 8363 Email info custommade co nz www custommade co nz Larcombs Vineyard ou Main S ton Temple d th Roa M CUSTO e scale A4 Scale Not maRAdGto E Lar GA S DOOR com bs R oad d Berketts ts RoaRoad Berket 276 Larcombs Road R D 5 Factory Weddons and Office Christchurch Phone 03 347 8333 276 Larcombs Road Fax 03 347 8363 Christchurch Email Weedons info custommade co nz Website www custommade co nz TOM e mAaRd G A E G ORS DO CUS