Return to flip book view
AGRICULTURAL I LIGHT COMMERCIAL I RESIDENTIALSTANDARD DETAILS & TOTAL SYSTEMSFOR METAL ROOFING AND SIDING
TABLE OF CONTENTSDue to Product improvements, changes and other factors, Fabral reserves the right to change or delete information herein without prior notice or obligation to make changes in products previously purchased. The details and written instructions described in this manual are suggested installation methods to ensure quality application of our products, and should be considered as a guideline only. FABRAL recognizes that installation techniques can vary based on builder and geographical preferences, and that there are other acceptable ways to install our products.Installation Instructions ......... 2Load Tables & Testing ........... 4Roof & Wall SystemsExposed Fastener Panels Grandrib 3 ..............................................................5 Grandrib 3 Plus ......................................................5 GRG ....................................................................... 5 Grandrib Liner ........................................................5 Mighti-Rib ..............................................................6 PBR ......................................................................6 ProClad ..................................................................6 Prime Rib ............................................................... 62 ½" Corrugated ................................................... 7 Strongrib ...............................................................7Concealed Fastener Panels Horizon 16 .............................................................8 Horizon S ...............................................................8 Horizon S100 .........................................................8 1 ⁄" SSR ...............................................................8 1 ⁄" SSR 150 ........................................................8Flashing & Trim Post Frame .............................................................12 Exposed Fastener ...................................................16 Mighti-Rib ..............................................................17 St. Joseph, MN .......................................................18 Salt Lake City, UT and Spokane, WA ........................ 19Trim Details...................20-42 System Components Flashing and Trim ..................................................43 Sots ..................................................................43 Underlayment ....................................................... 43 High Temp Underlayment ...................................... 44 Polycarbonate Panels ........................................... 44 Liner Panels ......................................................... 44 Snow Retention .................................................... 45 Venting and Closures ............................................ 45 Fasteners ............................................................. 46 Sealants .............................................................. 46 CondenStop® ......................................................... 47Accessories Flat Sheets ............................................................ 47 Cupolas ................................................................47 Pipe Boots ............................................................48 Door and Door Tracks ............................................48 Touch-up Paint ......................................................48Warranty Information ........... 49Contact Information .............. 5011
panels. For more detailed information on re-roong applications, consult FABRAL Technical Bulletin #721, Re-Roong With Metal. Load tables are available for all FABRAL panels; contact FABRAL for additional information.Roong Panel sidelaps should face away from wind driven rain. To accomplish this, begin by installing the rst sheet square with the eave and gable at the down wind end of the roof, farthest away from the source of prevailing winds or away from the primary viewing location. In applications requiring a panel endlap, please refer to the detailed instructions in this booklet. For best results, lap panels as shown and install in the indicated sequence. ALL ENDLAPS REQUIRE SEALANT. WHEN WEATHER-TIGHTNESS IS CRITICAL, USE SEALANT TAPE IN ALL SIDELAPS. To provide a drip edge, allow an overhang of 1 to 2 inches at the eave. At the gable edge, use a gable or sidewall ashing. This will keep weather out, prevent lifting in high winds, and provide a neat, nished appearance. The trim and roong sheet should be fastened every 12 to 24 inches along the gable edge. Do not step on panel ribs or on trim pieces to prevent kinking.Roof Pitch The metal roong panels shown in this manual require a minimum slope of 2½" per foot to ensure proper drainage. Refer to the rain-carrying table in this booklet for the maximum allowable panel length per slope that will provide adequate drainage. For longer slopes and lower roof pitches, contact FABRAL for other suitable proles.Bending and Bowing Aluminum and Steel roong and siding sheets are roll-formed from hardened, tempered metal for maximum strength. If a sheet must be bent, a gentle 90-degree bend is the maximum recommended. Metal should not be re-bent once it has been formed, nor should it be folded back on itself. When a metal roong sheet must be installed on a curved roof, screws should be installed at every overlapping rib at the sheet ends to resist the natural tendency of the metal to spring back. The standard fastening pattern is permitted over the rest of the sheet. When installing the metal panels shown in this booklet over a curved arch, the minimum radius of the arch is 18’ for aluminum panels and 24’ for steel panels. Use sealant tape or butyl caulking at all sidelaps and endlaps. Additional care and fasteners must be provided when securing the top and bottom purlins on an arched rafter building to prevent the curved pan-els from pulling the purlins loose from the rafters. Ring-shank pole barn nails, heavy wood screws, lag screws, or bolts are often used for attaching these purlins.Siding Siding should be installed using the standard fastening and overlap patterns to ensure optimum performance. For strong, neat corners use hemmed corner ashings. DO NOT RUN SIDING SHEETS ALL THE WAY TO THE GROUND. INSTEAD, PROVIDE A PROTECTIVE BASE OF CONCRETE, MASONRY, TREATED WOOD, OR SIMILAR MATERIAL AND TERMINATE THE SIDING SHEETS 6" ABOVE GRADE. If siding sheets are installed horizontally, use sealant tape or butyl caulking at the vertical laps to ensure weather-tight joints. Install panels from the bottom up so that water is directed away from, and not into, the lap joints.INSTALLATION INSTRUCTIONSBuilding Design and Construction In order to ensure the anticipated performance and longevity, protect metal panels from potentially corrosive situations and materials. When treated lumber will be in direct contact with metal panels or ashings please note the following: Galvanized steel is compatible with the CCA (Chromated Copper Arsenate) pressure-treated lumber that was predominantly used before 2004, but not with the older Penta treated lumber or the new ACQ (Alkaline Copper Quartenary), CA (Copper Azole), or CBA (Copper Boron Azole). Stainless steel or other special treated fasteners should be used into these non-compatible pressure treated lumbers. Aluminum must be separated from contact with all treated wood since the soluble copper in the preservative is corrosive to aluminum. Likewise, dissimilar metals also require a protective barrier between them to prevent galvanic corrosion. Request FABRAL Technical Bulletins #803, 106, and 107 for more information on treated lumber and dissimilar metals. PLASTIC, BUILDERS’ FELT, BITUMINOUS PAINT, CAULKING, OR GASKET MATERIAL MAY BE USED TO SEPARATE PANELS FROM TREATED WOOD AND DISSIMILAR METALS. When using aluminum panels in direct contact with steel, use a separator as described above and fasten with Stainless Steel screws. Fertilizer, lime, acids, feeds, manure, soils, and many other compounds also cause corrosion in metal panels. Contact between metal panels and any potentially corrosive materials should be prevented. Porous insulation materials may absorb and retain moisture, and should not be used in direct contact with metal panels. Use a vapor barrier such as polyethylene plastic or 30-lb felt to prevent moisture from contacting both the insulation and the metal panel. FABRAL’s translucent panels are intended for siding applications only. In all situations, foot trafc should be avoided on translucent panels. Translucent panels used in roong applications will break down in a short time and cause staining and premature corrosion of the metal panels below. If used on roofs, apply butyl caulking to separate the berglass panels from the metal. Translucent panels should be cleaned and sealed regularly, as recommended by the translucent panel manufacturer.Purlins, Girts and Roof Deck The substructure to which the metal panels are fastened must be properly spaced and sufciently thick to provide a roof or wall system able to meet required design loads. A 2" nominal lumber thickness or 1" nominal thickness are both acceptable purlins. If snow guards are to be installed in the future, a 2 x 8 purlin can be installed in the area for snow guard installation. Call engineering for locations of 2 x 8 purlins. When using purlins, FABRAL recommends a maximum spacing of 24" on-center. Pullout values decrease if the fasteners protrude completely through the purlins. Kiln-dried softwood is recommended for purlins or decking (pine, r, hemlock, and spruce). Hardwoods are difcult to fasten into without splitting and contain tannic acids that are corrosive to metal panels. Green (non-kiln-dried) lumber may warp, twist, and shrink as the wood seasons fully,causing waviness in the panels as well as loosening and leaking of the fasteners. Solid decking is required for all residential applications. When using solid decking or sheathing, always use 30-lb felt or underlayment and plan on using closer fastener spacing and larger diameter #14 screws. (Refer to the tables on page 4). On re-roong projects where the condition of the old decking is in question, or where existing shingles will be left in place, new 2x4 or 1x4 purlins should be fastened through the decking and into the rafters. This will provide a solid framework for attaching the metal22
Fastening FABRAL can supply either screws or nails for fastening into dimension lumber. Always use screws with solid sheathing. Screws for use with steel panels are galvanized and then coat-ed with an organic polymer for optimum corrosion resistance. For best results with aluminum panels, use #300 series stainless Wood screws with combination metal and neoprene washers should be installed in the at area of the panel adjacent to the ribs, and tightened such that the washer is compressed as illustrated above. This will ensure a lasting, leak-proof seal. REMOVE ANY METAL FILINGS CREATED BY THE DRILLING ACTION OF THE SCREWS OR PRE-DRILLING OF THE HOLES TO AVOID RUST STAINING ON THE PANEL SURFACE. Stitch screws should be used in the panel side joints when butyl sealant is used. They may also be used any time the side joint is not pulled together tightly to improve the appearance. Refer to the fastening schedules in this booklet for the correct fastener locations.Panels adhered with CondenStop Full length panels from eave to ridge are recommended, eave overhangs, valleys and any other edges exposed to the weather should be painted to seal microbers from absorbing moisture from the outside. The use of butyl sealant tape at these locations will also help to seal the microbers and prevent moisture from passing beyond the butyl. Wet stack storage still applies to panels with condenstop applied. Please store properly by covering and tilting one end. It’s always best if they can be stored inside if not being immediately installed.Flashing and Trim Always begin ashing installation from the bottom and work up, so that upper ashings are lapped on top of lower ashings. This will prevent moisture from leaking under the ashings and into the structure. Endlap ashings a minimum of 6" and seal the lap joints with sealant. Extend ashings 4-6" beyond the building, cut along the bend lines, apply sealant, and fold the side aps in and the top aps down to cap off the ends. Secure with pop-rivets or stitch screws. Some roof conditions, such as valleys, may require a longer endlap and/or a larger ashing to properly drain moisture from the roof. Factors that inuence ashing size, shape, and endlap requirements include roof pitch, roof geometry, slope length, and climatic factors (such as heavy snowfall or rainfall). Whenever possible, begin trim installation at the downwind end of the roof, farthest away from the source of prevailing winds, to allow ashing laps to face away from wind-driven rain. Refer to the details in this book for the proper location of fasteners and sealants. The ashings and trims shown in this book are standard parts. Custom trims are available to meet your specic design needs. Contact a Fabral dealer for information on custom trim. Refer to the SMACNA Architectural Sheet Metal Manual for additional information about detailing and installing ashings. Safety Work safely when installing metal products and use ex-treme caution on the roof at all times. Wear gloves and safety glasses to reduce the risk of injury, and use hearing protection when operating power tools. Be sure that ladders are safely special equipment may be required; Consult OSHA guidelines for compliance with all safety requirements. Do Not walk on panels until all the fasteners are installed. Metal roong panels are slippery when wet, dusty, frosty, or oily -- Do Not attempt to walk on a metal roof under these conditions. Wear soft-soled shoes to improve traction and to minimize damage to the paint nish. Always be aware of your position on the roof relative to any roof openings, roof edges, co-workers, and penetrations. Installing metal panels or ashings on a windy day can be dangerous and should be avoided if possible. Cutting Aluminum Panels To make a cut parallel to the ribs, score the panel deeply with a sharp utility knife and bend back-and-forth along the score, breaking the metal off cleanly. For cuts across the ribs, use straight-cut snips, electric or pneumatic shears, a portable prole shear, or an electric nibbler. Some installers prefer using a circular saw with a metal cutting blade (a ne-tooth hardwood blade, or a standard combination blade reversed in the saw works also). Light oil or soap on the blade will make cutting easier. Cutting and Drilling Steel Panels Steel panels may be cut with metal snips, electric or pneumatic shears, a portable prole shear, or an electric nibbler. Some installers prefer using a circular saw to cut metal panels. Do Not use self- consuming abrasive blades because of the following: 1. Abrasive blades burn the paint and galvanizing at the cut edge, leaving edges that are jagged and unsightly and rust more quickly 2. Abrasive blades produce hot metal lings that embed in the paint and cause rust marks on the face of the panel. If saw cutting cannot be avoided, select a carbide-tipped blade specially designed for cutting light-gage ferrous metal panels. These blades are now available at many home centers and lumber yards. 1. All saw cut panels must be turned face down and cut in a location down-wind and well away from the building and other panels to avoid embedment of metal lings on other panels 2. All saw cut panels must be thoroughly wiped to ensure the removal of all metal lings. Pre-drilling wall panels gives uniform alignment of screw rows. BE SURE TO REMOVE ANY FILINGS ONCE PANELS ARE INSTALLED TO AVOID RUST MARKS FROM THE FILINGS. Building Maintenance A metal roof should be inspected annually and cleaned as necessary to maintain its beauty and performance. Any debris or residue, including leaves, twigs, and dust should be cleaned off promptly to prevent moisture entrapment against the metal, which may lead to nish deterioration or premature corrosion. Flashings may need to be re-sealed periodically in order to maintain optimum weathertightness.Proper Storage Store metal panels indoors when possible; if outdoors, cover and elevate. Elevate one side higher for water drainage. Never cover in plastic; us a tarp that can breath. Allow for air circulation. If a bundle gets wet, break bands and separate sheets; allow sheets to dry completely and only re-stack if completely dry. Product should be stored for a maximum of 2-4 weeks before being installed. Spray Foam Insulation When insulating metal with spray foam insulation, the rst application layer should be getting the insulation behind all framing members. When completing the insulation, ensure the spray foam is installed in 2" thick layers (maximum) until desired thickness is achieved.CorrectUnder-DrivenOver-DrivenINSTALLATION INSTRUCTIONS33
UL RATINGSUL790 Class A Fire Rating applies to all Steel panels 29 ga and thicker and all Aluminum panels .032" and thicker.UL2218 Class 4 Hail Impact Rating applies to all Steel panels 29 ga and thicker and all Aluminum panels .032" and thicker.This table is provided as a courtesy to our customers to give approximate allowable wind speeds for typical residential buildings using the standard fastening schedule as shown in this book. Fasteners shall have an embedment depth listed above or fully penetrating plywood or OSB. Contact Fabral Engineering for detailed design values.LOAD TABLES & TESTINGSubstrate Fastener 9" 12" 15" 18" 21" 24"3/4" Plywood #14 Woodtite 317 mph 274 mph 245 mph 225 mph 207 mph 195 mph5/8" Plywood #14 Woodtite 245 mph 212 mph 189 mph 172 mph 159 mph 150 mph1/2" Plywood #14 Woodtite 269 mph 233 mph 209 mph 190 mph 176 mph 164 mph19/32" OSB #14 Woodtite 205 mph 177 mph 158 mph 144 mph 133 mph 125 mph7/16" OSB #14 Woodtite 171 mph 148 mph 133 mph 120 mph 112 mph 104 mphSPF #2 (1.5" Pen.) #14 Woodtite 388 mph 336 mph 300 mph 275 mph 242 mph 212 mphSPF #2 (1" Pen.) #10 Woodtite HLX 273 mph 236 mph 211 mph 193 mph 178 mph 167 mphSPF #2 (1.5" Pen.) #10 Woodtite HLX 359 mph 311 mph 278 mph 254 mph 234 mph 212 mphScrews Per Square 210 160 130 110 90 80LOAD TABLES & TESTINGTable per ASCE 7-10: category II (residential), exposure B (neighborhood), 4:12 gable roof, mean roof height 18', roof zone 3Spacing of Fastener Rows4FABRAL.COM800-4FABRAL (432-2725)
EXPOSED FASTENER PANELSGRANDRIB 3®See page 6 for a load tableIntermediate Roof Purlins and All SidingSCREW PATTERNSEaves and Endlaps - Roof PurlinsIntermediate Roof Purlins and All SidingSCREW PATTERNSEaves and Endlaps - Roof PurlinsSCREW PATTERNSGrandrib 3 is the “benchmark of the industry” and can be used for walls and roofs. This unique and versatile panel is available in a variety of popular colors. The panels have clean traditional lines, and are manufactured from the best structural steel available. Also available in .015 aluminum, true white only by special order.GRGThese panels are made of utility grade construction with zinc aluminum protective coating. The vertical lines and popular colors make this an economical and durable solution for a variety of structures. 9"37 3/4" Formed Width36" Coverage3/4"GRANDRIB 3+This enhanced version of the original Grandrib 3 panel has a G-90 coating for better weather performance and durability. Grandrib 3 Plus is a thicker metal panel, increasing strength and appearance while still providing the traditional benefits of a metal roof. Complete with a wide range of color selections, this panel is a superior choice.RECOMMENDEDPITCH:GAUGE:2½:12 29 OR 26 80 SCREWSPER SQUARE RECOMMENDEDOSB or PLYWOOD#14 x 1” WoodtiteType 17PURLINS#10 x ½” HLXType 17GRANDRIB LINER PANELAvailable in Galvanized G30 or .015 AluminumPANEL AVAILABILITY VARIES BY REGION. CONTACT FABRAL® FOR MORE INFORMATION.5800-4FABRAL (432-2725)
MIGHTI-RIB®39" Formed Width36" Coverage12" 4 3/8" 4 3/8"3 1/4"1 1/4"SCREW PATTERNROOFING - EAVES, RIDGES AND ENDLAPSROOFING - INTERMEDIATE SUPPORTSSIDING - ALL SUPPORTSPROCLAD36" Coverage9"5/8"Intermediate Roof Purlins and All SidingSCREW PATTERNSEaves and Endlaps - Roof PurlinsSidelap DetailPRIME RIB®SCREW PATTERNALL SUPPORTSSidelap SCREW PATTERNINTERMEDIATE ROOF PURLINS AND ALL SIDINGEAVES AND ENDLAPS - ROOF PURLINSIntermediate Roof Purlins and All SidingSCREW PATTERNSEaves and Endlaps - Roof PurlinsPANEL AVAILABILITY VARIES BY REGION. CONTACT FABRAL® FOR MORE INFORMATION.*Spokane and Fort Worth market onlyPBR*St. Joseph, MN, Marshfield, WI, and Gridley, IL markets only*St. Joseph, MN, Marshfield, WI, and Gridley, IL markets onlyEXPOSED FASTENER PANELSSTITCH SCREWS REQUIRED IN CERTAIN APPLICATIONS.SCREW PATTERNROOFING - EAVES, RIDGES AND ENDLAPSROOFING - INTERMEDIATE SUPPORTSSIDING - ALL SUPPORTS6800-4FABRAL (432-2725)
EXPOSED FASTENER PANELS2 ½" CORRUGATED24" Coverage2 2/3"1/2"26" Formed WidthNote: Roofing panels require side laps cover two corrugations. *Available in plain galvanized only.SCREW PATTERNROOFING - EAVES, RIDGES, AND ENDLAPSROOFING - INTERMEDIATE SUPPORTSSIDING - ALL SUPPORTSSCREW PATTERNROOFING - INTERMEDIATE SUPPORTSROOFING - EAVES, RIDGES, AND ENDLAPSSIDING - ALL SUPPORTSSCREW PATTERNROOFING - INTERMEDIATE SUPPORTSROOFING - EAVES, RIDGES, AND ENDLAPSSIDING - ALL SUPPORTSSCREW PATTERNEAVE AND ENDLAPS - ROOF PURLINSINTERMEDIATE ROOF PURLINS AND ALL SIDINGCorrect Strongrib SidelapBUTYL SEALANTLOCATION (OPTIONALFIELD APPLIED)PURLIN BEARINGLEGSTRONGRIB®.018 Aluminum, Plain and Painted White 36" Coverage (37 3/4" Formed Width)9"2 1/2"3/4"Wall application- 24" coverage with 1 rib overlapRoof application- 21 ⁄" coverage with 2 rib overlap*Available in Lancaster, PA market only in .018 Diamond embossed PANEL AVAILABILITY VARIES BY REGION. CONTACT FABRAL® FOR MORE INFORMATION.7800-4FABRAL (432-2725)
CONCEALED FASTENER PANELSHORIZON 161"16" Coverage1 ½" SSR HORIZON S16" Coverage1"HORIZON S1001 ½" SSR 15016"112"FOR CONCEALED FASTENER PANELS PLEASE REFERENCE THE HORIZON AND SSR INSTALLATION MANUALS FOR TRIM AND FASTENER DETAILS.FEATURES STIFFENING PANELS TO ENHANCE THE APPEARANCE OF THIS PANEL. *Available only in Spokane RegionFEATURES STANDARD SHADOW LINES TO ENHANCE THE APPEARANCE OF THIS PANEL* Available only in Lancaster RegionFEATURES STANDARD SHADOW LINES TO ENHANCE THE APPEARANCE OF THIS PANEL *Available in Gridley, Marshfield, Salt Lake City, and St. Joseph RegionsFEATURES STANDARD SHADOW LINES TO ENHANCE THE APPEARANCE OF THIS PANEL.* Available only in Lancaster RegionFEATURES STANDARD SHADOW LINES TO ENHANCE THE APPEARANCE OF THIS PANEL*Available in Gridley, Marshfield, Salt Lake City, and St. Joseph RegionsPANEL AVAILABILITY VARIES BY REGION. CONTACT FABRAL® FOR MORE INFORMATION.8800-4FABRAL (432-2725)
WHEN INSTALLING 2 1/2" OR 1 1/4" CORRUGATED ROOFING USE INSTALLATION SEQUENCE AS SHOWNENDLAP TAPETHIS EDGESIDELAP TAPETHIS EDGE15423"L" (IN FEET)PREVAILING WINDLoSIDELAP TAPETHIS EDGESKIRT BOARD OFTREATED LUMBER ORFOUNDATION OF BLOCK 12" TO 18" FROM GROUND LEVELEAVE OVERHANG1" TO 2"START END31ENDLAP TAPE ALIGNWITH PURLIN EDGEINSTALLATION SEQUENCEFOR STRONGRIB, GRANDRIB 3L542WHEN INSTALLING 2 1/2" OR 1 1/4" CORRUGATED ROOFING USE INSTALLATION SEQUENCE AS SHOWNENDLAP TAPETHIS EDGESIDELAP TAPETHIS EDGE15423"L" (IN FEET)PREVAILING WINDLoSIDELAP TAPETHIS EDGESKIRT BOARD OFTREATED LUMBER ORFOUNDATION OF BLOCK 12" TO 18" FROM GROUND LEVELEAVE OVERHANG1" TO 2"START END31ENDLAP TAPE ALIGNWITH PURLIN EDGEINSTALLATION SEQUENCEFOR STRONGRIB, GRANDRIB 3L5421. Apply ⁄" x ⁄" butyl endlap sealant on bottom panel just below centerline of purlin (see endlap diagram for location) on panel #1.2. Apply sidelap sealant on panel #1 and connect to endlap sealant.3. Place panel #2 so it overlaps panel #1, 12" as shown. Install screws per endlap fastening pattern.4. Apply sidelap sealant on panel #2 to connect to sidelap sealant of panel #1.5. Place panel #3 over sidelap of #1 and #2.6. Apply endlap sealant on panel #3.7. Apply sidelap sealant on panel #3 and connect with endlap sealant.8. Place panel #4 over endlap of panel #3. Install screws per endlap pattern.9. Repeat sequence for entire roof.ENDLAP & LONG RUN ENDLAPPING INSTRUCTIONSFLOATING LAP FOR ALUMINUM AND 3+ STEEL RUNSSTEP #2STEP #1ROOF PANEL10" To SealantENDLAP PATTERNBUTYL SEALANT TAPECONTINUOUS BEAD OF 3/32" x 1/2"2" OVERLAPPINGFROM PURLIN EDGE2"OVERLAPPINGFROM PURLIN EDGEDOWN SLOPEDOWN SLOPEROOF PANEL6 1/2"3 1/2"12" Total Lap3 1/2"FASTENERS @6 1/2"PURLINFLASHING DETAILS - POST FRAMEFIXED LAP FOR 2 STEEL RUNS9FABRAL.COM800-4FABRAL (432-2725)
PIPE PENETRATION VALLEY RIDGE/PEAK SIDEWALL GABLE/RAKESKYLIGHTCHIMNEY EAVE TRANSITION HIP ENDWALL1. Determine the thickness and type of substrate to be used to support the metal roofing. Solid decking is required for all residential applications (i.e., plywood, OSB).2. Refer to the Load-Span tables to select the proper fastener and spacing to meet loads on your structure. 3. Consult local building codes and restrictions to determine acceptable methods of construction for residential applications in your area.4. Solid decking with 30# felt or synthetic underlayment for residential applications is required. Ice & water shield or similar self-adhesive membrane is recommended at all valleys, dormers, chimneys, transitions, skylights and other critical areas.5. When re-roofing over an existing shingle roof with metal panels, Fabral recommends to install a new underlayment with 2x4 or 1x4 furring strips and attach the panels to the furring strips. Panels may be attached directly over shingles with an underlayment however please see technical bulletin #721 for more information.6. ZIP System® sheathing, which has a “built in” vapor barrier, is an acceptable substrate and vapor barrier.7. Request Fabral’s technical bulletins #720 and #721 for more details on residential roofing.BUILDING DETAILSEXPOSED FASTENER PANEL - RESIDENTIAL10FABRAL.COM800-4FABRAL (432-2725)
BUILDING DETAILSEXPOSED FASTENER PANEL - POST FRAMEGablep. 25Ridge/Peakp. 27Zeep. 33J-Channel/ Doors/Windowsp. 29Endwallp. 22Inside Cornerp. 34Sidewallp. 22Outside Cornerp. 34Eavep. 2011FABRAL.COM800-4FABRAL (432-2725)
#45 Liner ChannelF-J TrimAll ashing is 10' 6" in length and available in steel and aluminum, unless otherwise noted. Please contact Fabral for specics on the trim available in your area.AJ2Jamb TrimAJ6Jamb TrimAJ5Jamb TrimAJ4Jamb TrimAJ3J ChannelRJ8J ChannelRJ9F-J TrimPJFBOne Piece Door TrimF-J 10 TrimMidwest OnlyFLASHING & TRIM - POST FRAME1 1/4"2 7/8"2 3/8"1/2"7/8"7/8"P=Painted12FABRAL.COM800-4FABRAL (432-2725)
AG1 Gable/RakeAG4GableLonger Lengths AvailableAC1CornerLonger Lengths AvailableAC2Inside CornerAC3CornerLonger Lengths AvailableAC4CornerLonger Lengths AvailableRG1Residential GableLonger Lengths AvailableWG1ResidentialGableLonger Lengths AvailableAH2Door Track CoverAH3Double Door Track CoverAH4Door Track CoverAH5Door Track CoverFLASHING & TRIM - POST FRAME13FABRAL.COM800-4FABRAL (432-2725)
5NotchedAR3 w/ Versavent RX-10Ridge CapRR1Universal Ridge/Hip FlashAR3Ridge CapSBSnow Break(Solid Deck)CE1Denver EaveAT1Transition FlashAT2Gambrel FlashASW1Sidewall/Endwall FlashAGRN4Notched Gambrel FlashAvailable in 40 1/2" length onlyAEWN4Notched Endwall FlashAvailable in 40 1/2" length onlyAH6Door Track CoverAH8Double Track CoverAH9Double Track CoverCP1Monoslope RidgeSB1Snow Break(2x4 Purlins)2 1/8”1 1/2”3/4”3/4”1 1/2”1/2" Open Hem34118°718156°5142°11/2" Open Hem34158152°718156°142°15FLASHING & TRIM - POST FRAME14FABRAL.COM800-4FABRAL (432-2725)
*Other sizes are available upon request. Angle Flashing Beads vary by plant.2 3/16”AL2, 3, 4, 5Angle FlashingLonger Lengths AvailableAL6Angle FlashingAL7Angle FlashingAL8Angle FlashingAL9Angle FlashingAL10Angle FlashingABG1Base Guard203 Box BaseAZ2ZeeAD1Drip CapRV1Valley FlashRV2W-Valley Flash7 1/2"7 1/4"2 1/2"AB1Soft BoxAB2Soft BoxAE1Eave FlashAB3Soft BoxAB4Soft BoxRE1Eave FlashFLASHING & TRIM - POST FRAME15FABRAL.COM800-4FABRAL (432-2725)
FLASHING & TRIM - EXPOSED-FASTENER PANEL5RE1Residential EaveWG1Residential GableRG1Residential GableCE1Denver EaveRV1Valley FlashRV2W-Valley FlashRR1Universal Ridge/Hip FlashAR3Ridge CapAT1Transition FlashAT2Gambrel FlashAG4GableASW1Sidewall/Endwall FlashCP1Monoslope RidgeAll ashing is 10' 6" in length and available in steel and aluminum, unless otherwise noted. Please contact Fabral for specics on the trim available in your area.16FABRAL.COM800-4FABRAL (432-2725)
All Mighti-Rib® specic ashing is 10' 6" in length and available in steel, unless otherwise noted. Please contact Fabral for specics on the trim available in your area.115º555811116FE2Eave FlashingFR4Ridge CapFH1Head/Sill/Base FlashingFC3Gable/Outside Corner FlashFT1Endwall/Transition FlashFC4Inside Corner FlashFZ4Zee FlashFJ3 J Channel Flashing1 3/8"1 3/8"5/8"115°5"5"FLASHING & TRIM - MIGHTI-RIB®115º555811116111161617FABRAL.COM800-4FABRAL (432-2725)
FLASHING & TRIM - ST. JOSEPH, MNRegionally specic ashings and trims offered in addition to the standard offering. All ashing is 10’ 6” in length and available in steel and aluminum, unless otherwise noted. Please contact Fabral for specics on the trim available in your area.3/4”2 1/8”1 1/16”1 5/16”1/2”3 9/16”2 1/4”2 1/8”1/2”1/2”1 1/16”2 3/8"13/16"1 1/16"3/4"2 3/8"3 3/8”1”1 1/2”7/8”1/2”3/4”Overhead with DripDJ975 Door JambDJ75 Door Jamb 9 3/4”1 5/8”1 1/2”1 1/8”1 1/2”1 1/8”1 5/8”10’6,12’6,14’6, and 16’610’6,12’6,14’6, and 16’610’6,12’6,14’6, and 16’6AH3 Door Track CoverAH310'-6" LengthsFits National 5100, 5103and 5105 box rail.Matches National trim #5120(Replaces STC-504)1 3/8"3 3/8"2 3/8"2 5/16"1/2"1 3/4"2 1/2"1 1/16"3/4"3 1/2"135 DegreesClosed HemAL7 Angle20” Ridge Cap24” Poly/Fiberglass RidgeFull W2 Full Width W ValleyRV2 W Valley CW Ceiling Wall RJ9 Soff VentAL7Angle Flashing1 1/2"2 5/16" 6 1/4”3”1/2”3/8”9 3/16"1"RV2W-Valley FlashSteel OnlyCustomer to specify roof pitchRJ9F-J Trim1 1/4"2 7/8"7/8"78"7/8”1 1/4”2 7/8”7/8”Track Board CoverHem Vertical Door AST AstragalCF CounterPB Pitch Break GPB Gambrel Pitch BreakMini Rake& CornerEave TrimWEW290ºEave Trim18FABRAL.COM800-4FABRAL (432-2725)
Regionally specic ashings and trims offered in addition to the standard offering. All ashing is 10’ 6” in length and available in steel & aluminum, unless otherwise noted. Please contact Fabral for specics on the trim available in your area.FLASHING & TRIM - SPOKANE, WA SALT LAKE CITY, UTCE2 Denver Eave ME1 Mini Eave G Style Eave D Style EaveAT2 Gambrel Flash AEW1 Endwall Trim ASW2 Sidewall Trim RV2 W ValleyWG4 Gable TrimWG5 Gable Trim MG1 Mini Gable WGF5 Swept Wing Gable TrimAR3 w/ Versavent RX-102"4"12"58"38"114"6"13"WL1 Wall Lite Metal STC03 Single Track CoverRJ9 F-J Channel Jamb CapCP2 Peak Cap SB Snow Break312"112"38"38"112"2"JC1, JC2, JC3 Jamb CapJC1=JC2=JC3=STC04 Single Track CoverAC1 Corner DTC04 Double Track Cover19FABRAL.COM800-4FABRAL (432-2725)
EAVEROOF PANELEAVE TRIM, CE-1SHOWNFASTENER @ EVERYMAJOR RIB OR 12" C/C MAX.ROOF PURLINSIDING PANELBUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREOUTSIDE CLOSURE(RECOMMENDED)BUTYL SEALANT TAPETOP & BOTTOM OFCLOSUREINSIDE CLOSUREFASTENER PER STANDARDEAVE PATTERNPOSTROOF TRUSSTOP PLATEEAVEBOX EAVETRIM DETAILS BOX EAVEROOF PANELEAVE TRIM, CE-1SHOWNFASTENER @ EVERY MAJORRIB OR 12" C/C MAX.SIDING PANELBUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREOUTSIDE CLOSURE(RECOMMENDED)BUTYL SEALANT TAPE TOP &BOTTOM OF CLOSUREINSIDE CLOSUREFASTENERTOP PLATESOFFIT BOX, AB-3SHOWNEAVE PURLINFASTENER PER STANDARD EAVE PATTER20FABRAL.COM800-4FABRAL (432-2725)
EAVE WITH GUTTER EAVE TRIM, RE-1 SHOWNROOF STRUCTUREBUTYL TAPE SEALANT ON TOP& BOTTOM OF CLOSUREINSIDE CLOSUREGUTTER & STRAPS BYOTHERSFASTENER PER STANDARDEAVE PATTERNRES. EAVE WITH GUTTERICE & WATER SHIELD &UNDERLAYMENT FOR ADDERWEATHER TIGHTNESSAll residential flashings are formed for a 4/12 pitch unless otherwise requested by the customer.VENTED EAVEVENTED EAVEBUTYL SEALANT TAPE TOP &BOTTOM OF CLOSUREINSIDE CLOSURETOP PLATEF/J TRIM, RJ-9SHOWNFASTENERFABRAL ALUMINUMSOFITROOF PANELEAVE TRIM, CE-1SHOWNFASTENER @ EVERYMAJOR RIB OR 12" C/C MAX.SIDING PANELFASTENER PER STANDARDEAVE PATTERNANGLE FLASHING, AL-3 SHOWNTRIM DETAILS 21FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS SIDEWALLSIDING PANELFASTENER PER STANDARD EAVE PATTERNSEALER STRIP W/BUTYL SEALANT TAPEGIRT2" FASTENER @24" C/C MAX.SIDEWALL FLASH, ASW-1 SHOWN(FIELD BEND AS REQUIRED)BUTYL SEALANTTAPESLOPING RAFTERPURLINROOF PANELSPACE AS REQ'DROOF PANELSIDEWALLENDWALLSIDING PANELINSIDE CLOSUREGIRTFASTENER PER STANDARD EAVE PATTERN2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP &BOTTOM OF CLOSUREOUSIDE CLOSUREROOF PANELPURLINENDWALL TRIM, ASW-1SHOWNENDWALL22FABRAL.COM800-4FABRAL (432-2725)
15. VALLEY (PAGE 22)6" MIN.NOTE: VALLEY FLASH MUST HAVE SOLLID SUPPORTLARGER VALLEYS MAY BE REQUIREDFOR LONG ROOF PANEL RUNS ORHEAVY SNOW AREAS.ROOF STRUCTURE, SOLID2X'S OR PLYWOODSEALER STRIP, 1" X 1" X 19'-8"BLOCK CLOSURE, FILL RIB VOIDSCUT ROOF PANEL ASNECESSARYBUTYL SEALANT TOP &BOTTOM OF SEALER STRIPVALLEY TRIM, RV-2 SHOWNSCREWS EACH SIDE OF MAIN RIB(EAVE / ENDLAP PATTERN)VALLEYRIDGE/ HIP TRIM,RR-1 SHOWNLOWER VALLEY TRIM,RV-2 SHOWNROOF PANELUNDERLAYMENTBUTYL TAPESEALANTUPPER VALLEYTRIM, RV-2 SHOWNOUTSIDE CLOSURE, TAPESEALANT TOP & BOTTOMUNIVERSAL CLOSURE, TAPESEALANT TOP & BOTTOMNOTE: ROOF PANELOMITTED ON OTHER SIDEOF RIDGE FOR CLARITY.DORMER VALLEYSDORMER VALLEYTRIM DETAILS 23FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS ROOF PANELROOF PANELFASTENER PER STANDARDEAVE PATTERN2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP &BOTTOM OF CLOSUREINSIDECLOSUREOUSIDE CLOSUREBUTYL SEALANTTAPE TOP &BOTTOM OFCLOSUREGAMBREL TRIM, AT-2SHOWNPURLINNOTE: SPECIFY BOTH ROOF PITCHES WHEN ORDERING AT-2 FLASH.GAMBRELGAMBREL2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANTTAPE TOP &BOTTOM OFCLOSUREOUSIDE CLOSUREBUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREINSIDE CLOSUREROOF PANELPURLINTRANSITION TRIM,AT-1 SHOWNFASTENERS PERSTANDARD EAVE PATTERNTRANSITIONNOTE: SPECIFY BOTH ROOF PITCHES WHENORDERING AT-1. STANDARD IS 9/12 TO 3/12.TRANSITION24FABRAL.COM800-4FABRAL (432-2725)
BOX GABLEVERSION 1FASTENERBUTYL TAPEGABLE TRIM, WG-1 SHOWNSCREW FASTENER@ 24" C/C MAX.ROOF PANELROOF STRUCTUREGABLEGABLEROOF PURLINBOX SOFFIT, AB-3SHOWNFASTENER @EVERY MAJOR RIBOR 12" C/C MAX.OUTSIDE CLOSURE(RECOMMENDED)END RAFTERSIDING PANELGABLE TRIM, AC-4SHOWNFASTENER @24" C/C MAX.BUTYL SEALANT TAPEBUTYL SEALANT TAPEFASTENER24" C/C MAX.ROOF PANEL BOX GABLEBUTYL SEALANT TAPE TOP &BOTTOM OF CLOSURETRIM DETAILS 25FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILSMONOSLOPE RIDGEMONOSLOPE RIDGE CAP, CP-1 SHOWN2" FASTENER @ EVERY MAIN RIBBUTYL SEALANT TAPE TOP &BOTTOM OF CLOSUREOUSIDE CLOSURESIDINGROOF SHEATHINGSLOPING RAFTERFLYING GABLEMONOSLOPE RIDGEFLYING GABLEEAVE TRIM, CE-1 SHOWN (90 DEGREE ANGLE)BUTYL SEALANT TOP &BOTTOM OF SEALER STRIPSEALER STRIP (ASPHALTIMPREGNATED)FASCIA BOARDOVERHANG ROOF PANELS TOCREATE APPROX. 1" OVERHANGFASTENERUNDERLAYMENT26FABRAL.COM800-4FABRAL (432-2725)
2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.RIDGE/ HIP CAP,AR-3 SHOWNROOF PANELUNDERLAYMENTROOF STRUCTUREVERSAVENT RX-10RES. VENTED RIDGE2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREOUTSIDE CLOSURE (ON HIP ROOFS USE 1" X 1"X 19'-8" SEALER STRIP AND RR-1 FLASHING)ROOF PANELUNDERLAYMENTROOF STRUCTURERES. RIDGE/HIPRIDGE FLASHING,AR-3 SHOWNNON VENTED RIDGE/HIPVENTED RIDGETRIM DETAILS 27FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILSVENTED RIDGEDECKINGHIP/RIDGE CAP, RR-1SHOWN2-1/2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.OUTSIDE CLOSURE WITH BUTYLSEALANT TOP AND BOTTOMROOF PANELOPTIONAL J-CHANNELFOR SUPPORTCORRUGATED VENTUNDERLAYMENTROOF PANEL FASTENERPER STANDARD PATTERNALTERNATE VENTED RIDGEBASE GUARDFLOORGRADETREATED BASE PLANKBARRIER BETWEEN METAL ANDACQ TREATED LUMBERBASE GUARD, ABG-1 SHOWNINSIDE CLOSURE (RECOMMENDED)STAINLESS STEEL FASTENER PERSTANDARD SIDING PATTERNSIDING PANEL6" MIN.BASE GUARD1/8” GAPBELOW PANEL28FABRAL.COM800-4FABRAL (432-2725)
DOORDOOR STOPANGLE FLASHING, AL-3SHOWNDRIP EDGE TRIM, AD-1SHOWNFASTENERS PERFASTENER PATTERNSIDING PANELDOOR HEADERDOOR HEADERDOOR HEADERDOOR JAMBGIRTFASTENERFASTENERS PERFASTENERPATTERNONE PIECE DOOR TRIM,PJFB SHOWNDOOR JAMBDOORDOOR STOPSIDING PANELDOOR JAMBSGIRTFASTENERFASTENERS PERFASTENERPATTERNJ- CHANNEL, AJ-3 SHOWNDOOR JAMBDOORDOOR STOPSIDING PANELANGLE FLASHING, AL-3SHOWNBUTYL SEALANT TAPEDOOR JAMBSVERSION 1 VERSION 2TRIM DETAILS 29FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS OVERHEAD DOOR JAMBSVERSION 1VERSION 2VERSION 3VERSION 4GIRTSIDING PANELFASTENERS PERFASTENER PATTERNOVERHEAD DOORPOSTDOOR JAMBDOOR JAMB1 X 3 GUIDEFASTENERJAMB TRIM, AJ-4SHOWNBUTYL SEALANTTAPEBUTYL SEALANTTAPEFASTENERANGLE FLASHING, AL-5 SHOWN(PER DEPTH)OVERHEAD DOOR JAMBSGIRTSIDING PANELFASTENERS PERFASTENER PATTERNOVERHEAD DOORPOSTDOOR JAMBDOOR JAMB1 X 3 GUIDEONE PIECE DOORTRIM, PJFB SHOWNFASTENERFLASH PJFBOVERHEAD DOOR JAMBSGIRTSIDING PANELFASTENERS PERFASTENER PATTERNOVERHEAD DOORPOSTDOOR JAMBDOOR JAMB1 X 3 GUIDEFASTENEROVERHEAD DOOR JAMBSONE PIECE DOORTRIM, PJFB SHOWNGIRTSIDING PANELFASTENERS PERFASTENER PATTERNOVERHEAD DOORPOSTDOOR JAMBDOOR JAMB1 X 3 GUIDEANGLE FLASHING,AL-3 SHOWNBUTYL SEALANTTAPEFASTENERJ-CHANNEL, AJ-3SHOWNOVERHEAD DOOR JAMBS30FABRAL.COM800-4FABRAL (432-2725)
SLIDING DOOR JAMBSLIDING DOOR BASEWALL GIRTSIDING PANELPOSTFASTENERJAMB TRIM, AJ-4SHOWNBUTYL SEALANTTAPEBUTYL SEALANTTAPEFASTENERANGLE FLASHING, AL-3SHOWNSLIDING DOOR JAMB DETAIL2 X 2 FILLER BLOCKBUTYL SEALANT TAPEANGLE FLASHING, AL-6SHOWNJ-CHANNEL, AJ-3 SHOWNFASTENERSIDING PANELSLIDING DOORSLIDING DOOR BASEFASTENERS PERFASTENER PATTERNSIDING PANEL ON SLIDING DOORSLIDING DOOR GIRTDRIP EDGE TRIM, AD-1 SHOWNTREATED BASE PLANKFLOORGRADETRIM DETAILS 31FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS SLIDING DOOR FACE MOUNT HEADER WITH 3-1 PC BRACKETSLIDING DOOR TOP MOUNT HEADER WITH 3 FB BRACKETSLIDING DOUBLE DOOR HEADER WITH8-3 CFB BRACKETSLIDING DOUBLE PACKED-OUT DOOR HEADER WITH8-3 CFB BRACKETSIDING PANELTRACK SUPPORT2 X 6 TRACK BOARDSIDING PANEL ON SLIDING DOORSLIDING DOOR GIRTFASTENERS PERFASTENER PATTERNFASTENERS PERFASTENER PATTERNSLIDING DOOR FACE MOUNT HEADEROVERHEAD DOOR TRACKAH5 DOOR TRACKCOVER3-1PC BRACKETSIDING PANELTRACK SUPPORT2 X 6 TRACK BOARDSIDING PANEL ON SLIDING DOORSLIDING DOOR GIRTFASTENERS PERFASTENER PATTERNFASTENERS PERFASTENER PATTERNSLIDING DOOR PACKED- OUT HEADEROVERHEAD DOOR TRACKAH6 DOOR TRACKCOVER3-FB BRACKET3-AC BRACKETSIDING PANELFASTENERS PERFASTENER PATTERNSIDING PANEL ON SLIDING DOORSLIDING DOOR GIRTFASTENERS PERFASTENER PATTERNSLIDING DOUBLE DOOR PACKED- OUTHEADER#3 SLOTTED ROUNDKEYHOLD TRACKTRACK SUPPORT2 X 6 TRACK BOARD8-3CFB BRACKETAH-9 (PACKED-OUT) BRACKETFLASHINGSIDING PANEL ON SLIDING DOORSLIDING DOOR GIRTSIDING PANELFASTENERS PERFASTENER PATTERNSIDING PANEL ON SLIDING DOORSLIDING DOOR GIRTFASTENERS PERFASTENER PATTERNSLIDING DOUBLE DOOR PACKED- OUTHEADER#3 SLOTTED ROUNDKEYHOLD TRACK TRACK BOARD8-3CFB BRACKETAH-8 (FACE-MOUNT) BRACKETFLASHINGSIDING PANEL ON SLIDING DOORSLIDING DOOR GIRT32FABRAL.COM800-4FABRAL (432-2725)
POLYCARBONATE PANELWINDOW SILL WINDOW HEADERFASTENERS PERFASTENER PATTERNZEE TRIM, AZ-2 SHOWNBUTYL SEALANT TAPEBUTYL SEALANT TAPEINSIDE CLOSURE(RECOMMENDED)OUTSIDE CLOSURE(RECOMMENDED)GIRT2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.METAL SIDING OR TRANSLUCENTROOF PANELMETAL SIDING OR TRANSLUCENTROOF PANELPOLYCARBONATE PANELFASTENERS PERFASTENER PATTERNSIDING PANEL2 X 41 X 6, BEVELEDWINDOW UNITJ-CHANNEL, AJ-3 SHOWNWINDOW SILLGIRTSIDING PANEL2 X 4BUTYL SEALANT TAPEFASTENERJ-CHANNEL, AJ-3SHOWNWINDOW UNITWINDOW JAMB2 X 4WINDOW UNITFASTENERS PERFASTENER PATTERNSIDING PANELBUTYL SEALANT TAPEINSIDE CLOSURE (RECOMMENDED)DRIP EDGE TRIM, AD-1SHOWNWINDOW HEADERWINDOW JAMBTRIM DETAILS 33FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS POSTBUTYL SEALANT TAPEFASTENER @24" C/C MAX.INSIDE CORNER TRIM, AC-2SHOWNFASTENERS PERFASTENER PATTERNGIRTSIDING PANELINSIDE CORNEROUTSIDE CORNERSVERSION 1CORNER TRIM,AC-3 SHOWNFASTENER @24" C/C MAX.BUTYL SEALANTTAPEPOSTGIRTFASTENERS PERFASTENER PATTERNSIDING PANELOUTSIDE CORNERCORNER TRIM,AC-1 SHOWNFASTENER @24" C/C MAX.BUTYL SEALANTTAPEPOSTGIRTFASTENERS PERFASTENER PATTERNSIDING PANELOUTSIDE CORNERINSIDE CORNER34FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS PIPE BOOTSROOF STRUCTUREROOF PANELSCREWS SPACED 2" TO 3" MAXAROUND BASE TO SECUREVENTILATION PIPE(OPTIONAL) SILICONE SEALANTAROUND CUT OF BOOTPIPE BOOTBUTYL SEALANT TAPEUNDER BSE OF PIPE BOOTRES. PIPE BOOTS35FABRAL.COM800-4FABRAL (432-2725)
ENDWALLSIDING2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP &BOTTOM OF CLOSUREOUTSIDE CLOSUREROOF STRUCTUREENDWALL TRIM, ASW-1SHOWNROOF PANELRES. ENDWALLSIDEWALLSIDING2" FASTENER @24" C/C MAX.SIDEWALL TRIM, ASW-1SHOWNBUTYL SEALANTTAPEROOF PANELICE WATER SHIELD ANDUNDERLAYMENT FOR ADDEDWEATHER TIGHTNESSROOFING STRUCTURERES. SIDEWALLTRIM DETAILSAll residential flashings are formed for a 4/12 pitch unless otherwise requested by the customer.36FABRAL.COM800-4FABRAL (432-2725)
VALLEYDORMER VALLEYRES. VALLEY6" MIN.ROOF STRUCTURE, SOLID2X'S OR PLYWOODSEALER STRIP, 1" X 1" X 19'-8"BLOCK CLOSURE, FILL RIB VOIDSCUT ROOF PANEL ASNECESSARYBUTYL SEALANT TOP &BOTTOM OF SEALER STRIPVALLEY FLASHING, RV-2 SHOWNSCREWS EACH SIDE OF MAIN RIB(EAVE / ENDLAP PATTERN)SOLID SUPPORT IS REQUIRED UNDER THEVALLEY. EPDM LINING IS RECOMMENDED UNDERLAPPED ROOF PANELS AND VALLEY FLASHING.LINING MUST CONTINUE DOWN TO EAVE LINE.RIDGE/ HIP TRIM,RR-1 SHOWNLOWER VALLEY TRIM,RV-2 SHOWNROOF PANELUNDERLAYMENTBUTYL TAPESEALANTUPPER VALLEYTRIM, RV-2 SHOWNOUTSIDE CLOSURE, TAPESEALANT TOP & BOTTOMUNIVERSAL CLOSURE, TAPESEALANT TOP & BOTTOMNOTE: ROOF PANELOMITTED ON OTHER SIDEOF RIDGE FOR CLARITY.DORMER VALLEYSTRIM DETAILS 37FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS ROOF PANELROOF PANELFASTENER PER STANDARDEAVE PATTERN2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREINSIDE CLOSUREOUTSIDE CLOSUREBUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREGAMBREL TRIM, AT-2 SHOWNROOF STRUCTURENOTE: SPECIFY BOTH ROOF PITCHES WHEN ORDERING AT-2 FLASH.RES. GAMBRELGAMBRELTRANSITIONFASTENER PER STANDARDEAVE PATTERN2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP &BOTTOM OF CLOSUREOUTSIDE CLOSUREBUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREINSIDE CLOSUREROOF PANELTRANSITION TRIM,AT-1 SHOWNROOF STRUCTURERES. TRANSITION38FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS SKYLIGHT59. SKYLIGHTFRAMING2" FASTENER @ 6" C/C MAX.SIDEWALL TRIM, ASW-1 SHOWNBUTYL SEALANT TAPEROOF PANELSKYLIGHTICE AND WATER SHIELDAND UNDERLAYMENTROOF STRUCTURESKYLIGHTSECTION A-A2" FASTENER @ 6" C/C MAX.FLASHING - REVERSE AL FLASHINGBUTYL SEALANT TAPEROOF PANELICE AND WATER SHIELDAND UNDERLAYMENTROOF STRUCTURECONTINUOUS SIKAFLEXCAULK @ PERIMETERSEALANTSKYLIGHTSKYLIGHTSECTION A-A2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREOUTSIDE CLOSUREROOF PANELENDWALL TRIM, ASW-1 SHOWNROOF STRUCTUREFRAMESKYLIGHTSEALANTICE AND WATER SHIELD &UNDERLAYMENTSKYLIGHTSECTION B-B59. SKYLIGHT59. SKYLIGHT39FABRAL.COM800-4FABRAL (432-2725)
CHIMNEY SIDEWALLSAW CUT REGLET 12" - 1" DEEP, BLOWOUT DUST & FILL WITH SIKAFLEXSEALANT. SET FLASH & FASTEN WITHCOMPATIBLE MASONRY ANCHOR.2" FASTENER @ 24" C/C MAX.SIDEWALL TRIM, ASW-1 SHOWN(FIELD MODIFY AS REQUIRED)BUTYL SEALANT TAPEROOF PANELBRICKICE AND WATER SHIELD ANDUNDERLAYMENTROOF STRUCTURECHIMNEYCHIMNEY ENDWALL 2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP &BOTTOM OF CLOSUREOUTSIDE CLOSUREENDWALL TRIM, ASW-1 SHOWN (FIELDMODIFIED TO FIT)SAW CUT REGLET 12" - 1" DEEP, BLOW OUT DUST& FILL WITH SIKAFLEX SEALANT. SET FLASH &FASTEN WITH COMPATIBLE MASONRY ANCHOR.BRICKROOF PANELROOF STRUCTUREICE AND WATER SHIELD ANDUNDERLAYMENTCHIMNEYTRIM DETAILS 40FABRAL.COM800-4FABRAL (432-2725)
TRIM DETAILS2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.BUTYL SEALANT TAPE TOP& BOTTOM OF CLOSUREOUTSIDE CLOSURE (ON HIP ROOFS USE 1" X 1"X 19'-8" SEALER STRIP AND RR-1 FLASHING)ROOF PANELUNDERLAYMENTROOF STRUCTURERES. RIDGE/HIPRIDGE FLASHING,AR-3 SHOWNRIDGE/HIP2" FASTENER @ EVERYMAIN RIB OR 12" C/C MAX.RIDGE/ HIP CAP,AR-3 SHOWNROOF PANELUNDERLAYMENTROOF STRUCTUREVERSAVENT RX-10RES. VENTED RIDGEVENTED RIDGE41FABRAL.COM800-4FABRAL (432-2725)
FASTENERBUTYL TAPEGABLE TRIM, WG-1 SHOWNSCREW FASTENER@ 24" C/C MAX.ROOF PANELROOF STRUCTUREGABLEGABLE42FABRAL.COM800-4FABRAL (432-2725)
FLASHING AND TRIMSYSTEM COMPONENTSFabral oers a standard package of flashing and trim for a variety of applications. Flashing is factory-formed at 10' 6" lengths and available in steel and aluminum with coordinating WeatherXL finishes and colors. Flat metal sheets are also available when installer fabrication is preferred. Flashing details and assistance with flashing details are available from your Fabral Customer Care representative. Standard details are illustrated in the Fabral Blue Book on pages 20-42.Sot panels keep buildings ventilated allowing them to “breathe” and helping to prevent damaging moisture from being trapped in attics and eaves. Various ventilation patterns can be accomplished by alternating solid and vented or perforated panels.SOFFIT DETAILS• Full, Center, and Non-Vented Sot Panels• Aluminum – recyclable and sustainable• Pre-cut 16" coverage• Quad 4 vented – 12.96 sq.in./lineal ft free airspace• Available in standard 12’ or precut lengthsSOLID SOFFITCENTER VENT FULL VENT Fabral Sots are available in three pre-formed engineered profiles - two ventilated (center and full) for increased air flow and one solid. *Sot availability will vary by market.Fabral oers the total system solution with RoofSeal underlayment. By combiningsuperior performance and protection with skid-resistant traction, RoofSeal helps youget the job done right.SPECS• Width: 4’• Length: 250’• Weight: 32 lbs• Thickness: 13.25 mils• UV exposure up to 180 days• Water Vapor Permeance: .06 perms• QAI & ICC-ES building code compliant• Contributes to LEED and NGBP ratings• 100% inorganic, will not rot or mold• 10 squares per roll • 36 rolls per pallet• Thickness: 13.25 milsROOFSEAL FEATURES• Durability: stronger than traditional felt• Quality: skid-resistant traction• Performance: UV exposure up to 180 days• Peace of mind: 50 year warranty against leakingSOFFITSROOFSEAL43FABRAL.COM800-4FABRAL (432-2725)
HIGH TEMPERATURE UNDERLAYMENT PEEL AND STICKFabral High-Temperature Underlayment is a durable, self-adhering, modified composite underlayment, specifically designed to withstand the rigors of most roofing applications. It is available to use as flashing tape to provide a secondary water barrier.• 30 year warranty out of the box• Adds to the complete system for Fabral roofing• Width: 3'• Length: 66'FEATURES:• UV protected surface – 90-day exposure• High-temperature stability – 260° F• 50 mil thickness• Soft-surfaced polyester face• Self-adhering and cold applied• No special adhesives necessary• Direct-to-deck metal application • 2 squares per rollCODES & COMPLIANCES:• Underwriters Laboratories Class A and Class C Fire Rating – Based on roof covering• ASTM D1970, Standard Ice Dam Underlayment• Florida Building Code Approved – FL 17322• Miami-Dade County Product Control Approved, MiamiDade County, FloridaTranslucent panels transmit natural light aording for better work conditions and potentially reducing energy costs. These wall siding panels are ideal for use in agricultural, light commercial, warehouse, and industrial facilities. Available in lengths: 8', 10' and 12'.POLYCARBONATE• Virtually unbreakable• Will not yellow• Easily and safely installed on sidewalls• Colors: Clear and White (Grandrib 3, Mighti-Rib, Ridge Caps)ProfileNameBasic Profile Dimensions† Standard Lengths (ft) Colors8' 10' 10½' * 12' 16' * Clear Soft White White Solar Gray*GrandRib 3GRG• • • • • •Mighti-Rib• • •RidgeCaps• •38"36"9"3/4"3/8"32/4"13/8"38"12"36"4"1-1/4"Ridge Cap Ridge Cap23" Width10'-6" Length1.625"- 4.0"Bend as required 24" WidthBend as required1.36"- 4.0"a b*Visit Fabral.com for additional non-stocked specialty profiles.Fabral liner panels are perfect for interior projects requiring additional insulation, strength or acoustical control. Additionally these panels are an economical light gauge panel solution for projects requiring partitions.• Custom cut lengths up to 40'• Easy to clean• Polyester paint finish• Acoustical panels perforated across entire panel• 36" coveragePOLYCARBONATE PANELSLINER PANELS44FABRAL.COM800-4FABRAL (432-2725)
SYSTEM COMPONENTSRoof ventilation and uniform airflow are key to keeping metal clad buildings “healthy.” Correctly engineered vent and closure systems “manage” weather limiting wind-driven rain from entering the ridge area and facilitating “moisture release.”VENTING AND CLOSURESCLOSURE SPECS• Available in Grandrib 3, Strongrib, 1¼" Corrugated, 2½" Corrugated and ProCladGrandrib 3, Strongrib, 114" Corrugated,212" Corrugated, 5V Crimp, and Fabrib available by location - check withsales service rep. ClosuresOutside (Ridge)Inside (Eave)RX-10 RIDGE CAP VENT*• Factory applied to the ridge cap• Save up to half of your installation time • Non-profile specific material • Clean, dust free installation • Virtually NO WASTED material• 1½" x 3" material provides 17 sq. inches/lineal foot free area at the ridgeRV35 AND RV100**• 10' metal ridge vent • Variety of colors available LP2 WEATHER-TITE RIDGE VENT• Available in Horizon S, Grandrib 3 and Mighti-Rib profiles• Lower, custom-fit profile• Moisture and pest barrier• Non-obtrusive appearance• Reduces utility costs• One-person installation*Available attached to ridge cap as RX-10 version and as X-10 version for field installation; not pre-applied to ridge capSNOW RETENTION SYSTEMSAny project in a freeze/thaw zone should employ a snow retention system. Metal roofs are naturally slippery so snow and ice move quickly over the smooth surface, potentially damaging plumbing stacks and lower roof planes and possibly endangering people and property. PC240 & BUSTER - EXPOSED FASTENERS-5 SNOW RETENTION - STANDING SEAM• UV stable, very strong • Polycarbonate Lexan 103-112 (⁄" thick for BUSTER)• Mounted with screws or adhesives• Patented, Made in the USA HEAVY DUTY LEXANPlease see page 17 (SB & SB1) for snow break details. * Not all locations stock RT MINI CLEAR SNOW GUARD – EXPOSED FASTENER• Premium polycarbonate plastic with UV stabilizers• Maximum protection, moderatly priced• Two-to-one base-to-blade ratio• 4.5 sq.in. and gusseted blade snow pocket • Typically installed by adhering to and mechanically fastened to the roofing panelRTCLSRRTCLSMPROFILE FIT VENT-ROLL• Available in Grandrib 3, 5V and SSR• 10.66 sq. in. per lineal ft. of ridge (5.33 / side)**Midwest OnlyCL SNOW GUARD - EXPOSED FASTENER• Premium polycarbonate plastic with UV stabilizers• Unique vent rib systems allows for adhesive out gassing• Three-to-one base-to-blade ratio adds significantly to strength• Documented holding strength• Compatible with all standing seam metal roof profiles45FABRAL.COM800-4FABRAL (432-2725)
SEALANTSFabral sealants provide a weather-tight seal against water, wind, dust, and dirt. Excellent for use on a variety of metal roof, trim siding, gutters, flashing and downspouts.TREMCO SEALANT• Waterproof sealant to fill gaps• Permanent flexibility - won’t crack• Standard color: Gray (stocked) • UV-resistant SEALANT TAPE• ⁄" x ¼" x 40' (sidelap)• ⁄" x ½" x 50' (endlap)SEALER STRIP• Use at valleys and hips• 1" x 1" x 19' 6.8" long#12-14 FLATTOP• Use to fasten into light gauge metal framing• Available in 1" and 1½"• ⁄" hex head with EPDM washer• Type 3 point can drill through .21" steel#10-16 300 SERIES STAINLESS STEEL• Use for high corrosive environments • Use with ALUMINUM panels• Available in 1", 1½", and 2"• ⁄" hex head, EPDM/metal washer• Use with treated lumber#10-14 410 STAINLESS STEEL• Use with 26 gauge or thinner to avoid pre-drilling• Available in 1", 1½", and 2"• ⁄" hex head, EPDM/metal washer• Use with steel panels installed on treated lumber#12x3/4" STITCH**• Use to stitch sidelap for exposed fastener panels • ⁄" hex head, EPDM/metal washerFASTENERSUnderstanding and installing which fasteners are best for which application is critical to any project. Be sure to match the correct screw or fastener option with the appropriate roof or wall system. For more information check with your FabralCore representative.* Painted ** Plain All fasteners 250/bag#14-10 WOODTITE• Use to fasten metal to plywood, OSB, or ZIP• Use for trim attachment• Available in 1", 1½", and 2"• ⁄" hex head, EPDM/metal washer• Oxyseal Long-Life Coating#10 HLX High Low• Use with dimensional lumber• Available in 1", 1½", 2", 2½" and 3"• ⁄" hex head, EPDM/metal washer• Oxyseal Long-Life Coating46FABRAL.COM800-4FABRAL (432-2725)
ACCESSORIESFLAT SHEETSFabral Flat Metal Sheets may be ordered for on-the-job fabrication. A wide variety of substrates are available including aluminum, galvanized steel, galvalume, copper and stainless steel. Flat sheets may be coated with our premium WeatherXL paint system oered in a full range of colors. Contact your local sales rep for Flat Sheet & Slit Coil details.Cupolas are an excellent way to bring architectural detail to any structure. Fabral cupolas are built to order and are oered in a variety of sizes (up to 66" x 66"), shapes and colors. Flashings can be built to any roof pitch and optional windows may be built into the side panels. Base sizes include 24" x 24", 36" x 36", and 48" x 48". Custom cupolas availableCUPOLASPRODUCT SPECIFICATIONS • Used for field forming crickets around the chimney, skylights, penetrations, and special flashing as necessary. • 29 gauge painted and plain galvanized • Full width (40 ⁄" 10'6")• Slit width available SYSTEM COMPONENTSCONDENSTOP™Stop condensation with Fabral factory applied CondenStop™. CondenStop saves time and money by reducing labor costs and installation time versus other condensation barriers. Easily and eectively prevent condensation and the problems caused by condensation by installing Fabral panels featuring CondenStop. • Protects assets and investments from moisture• Adds to interior corrosion protection• Light gray color enhances the indoor look of an open framing structure roof • Must be used on open purlin systems. Do not use CondenStop over solid decking• Available for the Grandrib 3 painted panel oerings47FABRAL.COM800-4FABRAL (432-2725)
Sealing small pipes is made easier with pipe boots from Fabral.The metal base with a dome-shaped boot serves as a covering for vent pipes.PIPE BOOTSFabral Door Systems include four door types and the complete corresponding track systems. For information on product availability, contact your Fabral representative.3100 SERIES DOOR• Pre-hung 4-way universal swing• 1-⁄" galvanized steel door• Pressure injected with polyurethane foam• Pre-painted with two coats of polyester paint5100 SERIES DOOR• Light commercial post frame entry door• Rolled edge door panel• 24-gauge polyester painted galvanized steel• Heavy internal aluminum stiles and rails• Heavy-duty 16-gauge 3-½" wide painted steel jambs• 12-gauge stainless steel 4-½" x 4" fixed pin PARTNER DOOR• Pre-finished/pre-hung 6-bend steel or extruded aluminum• Pre-hung 4-way universal swing• 29-gauge steel exteriorRESPONDER DOOR• Pre-finished/pre-hung 6-bend steel or extruded aluminum• Pre-hung 2-way universal swing• 29-gauge steel exteriorDOOR TRACK SYSTEM• Doors tracks, frames, bottom guide systems• Trolleys, brackets, latches• Rollers• Sliding door accessoriesDOOR AND DOOR TRACKSFabral oers touch up paints in a full range of WeatherXL colors. Contact your Fabral representative to order the color you require. TOUCH-UP PAINTEPDM SPECIFICATIONS • Colors: Gray and Black • Up to 250° FSILICON SPECIFICATIONS • Colors: Orange • Up to 450° F • Ranging for pipe sizes from 1" to 13" • Larger sizes available upon requestBase Diameter Item No. Min Max7 ⁄" 3 ⁄" 5"10 ⁄" 5 4 ⁄" 7 ⁄"16 ⁄" 8 7" 13"PIPE SIZESACCESSORIES*Retrofit boots available. Sizes vary.**Doors are not available in all markets and non-stock.*AJ doors available special order48FABRAL.COM800-4FABRAL (432-2725)
WARRANTYThe WeatherXL PLUS Warranty• Lifetime film integrity for walls & roofs• 30-year against fade & chalk for walls and roofs • 25-year non-perforation against acid rain for walls; 20-years for roof For profiles: Grandrib 3 PLUSAluminum Product Guarantee• 30-year corrosion guaranteeGalvalume® Perforation Warranty• 20-year non-perforation warranty for Grandrib 3, Mighti-Rib , Horizon S and 1 ½" SSRThe Weather XL Warranty for Galvalume® Panels• Lifetime film integrity for walls & roofs• 30-year against fade & chalk for walls and roofs• 20 year non-perforation warranty For profiles: Grandrib 3, 1 ½" SSR, Mighti-Rib, Horizon S, Horizon 16OTHER WARRANTIESProduct Warranties are available upon requestGRG™ Warranty• 40-year film integrity • 30-year prorated fade and chalk Galvalume is a registered trademark of BIEC International. WARRANTY COVERAGE Fabral offers some of the most competitive, enduring warranties in the industry.FILM INTEGRITY CHALK & FADE PERFORATION WALLSPERFORATION ROOFSGRANDRIB 3+ LIFETIME 30 YEARS 25 YEARS 20YEARSGRANDRIB 3 LIFETIME 30 YEARS 20 YEARS 20 YEARSGRG 40 YEARS30 YEARS (PRORATED) N/A N/ALINER PANEL N/A N/A N/A N/AMIGHTI-RIB LIFETIME 30 YEARS 20 YEARS 20 YEARSPBR LIFETIME 30 YEARS 20 YEARS 20 YEARSPROCLAD LIFETIME 30 YEARS 20 YEARS 20 YEARSPRIME RIB LIFETIME 30 YEARS 20 YEARS 20 YEARS2 ½" CORRUGATED N/A N/A N/A N/ASTRONGRIB N/A N/A N/A N/AHORIZON 16 LIFETIME 30 YEARS 20 YEARS 20 YEARSHORIZON S/S100 LIFETIME 30 YEARS 20 YEARS 20 YEARS1 ½" SSR/1 ½" SSR 150LIFETIME 30 YEARS 20 YEARS 20 YEARS49FABRAL.COM800-4FABRAL (432-2725)
Fort Worth, TX (817) 286-5100 Gridley, IL (309) 280-6205 Jackson, GA (770) 230-8093 Lancaster, PA (717) 638-2809Marsheld, WI (715) 800-6006Salt Lake City, UT (385) 243-6333Spokane, WA (509) 204-8013St. Joseph, MN (816)-205-8111 Contact by Phone - Nationwide Plant LocationsContact by Emailcustomercare@fgmfabral.comFABRAL LOCATIONS & SERVICE AREASCONTACT INFORMATIONSPOKANE, WASALT LAKE CITY, UTFORT WORTH, TX*JACKSON, GA*ST. JOSEPH, MNMARSHFIELD, WIGRIDLEY, ILLANCASTER, PA* Architectural Production Facility1-800-4FABRAL (432-2725)50FABRAL.COM800-4FABRAL (432-2725) Contact ACR Metal by Email ACR Metal 800-325-1247
info@acrmetal.com
ACR MetalDistributors
ACR Location
UL is the trademark of UL LLC Galvalume is the trademark of BIEC International Inc. © Fabral 2024 All rights reserved. 98-32-161 07/2024 FABRAL.COM | 1-800-4FABRAL (432-2725)