Return to flip book view
M-Loc™Commercial and Residential Roof and Wall PanelCENTRALSTATESCO.COMFLYR_MLOC_240412• M-Loc is a structural roof and wall panel that can be installed directly over purlins, joists, or solid decking.• This panel is produced in our Cedar Hill, TX, and Mount Airy, NC, facilities. Longer lead times may apply. This versatile panel has long served customers with lasting durability and a pleasing appearance. Its sturdy design provides resistance to the most severe weather and is an excellent choice when the project requires a commercial-strength panel with a low-rib appearance.An attractive and reliableall-purpose panel36"OVERALLCOVERAGE⁄"MAXIMUMRIB HEIGHT1:12PITCHAND ABOVE36" COVERAGE6" 13/16" RECOMMENDEDEC26GAUGECopyright © 2024, Central States Manufacturing, Inc., All Rights Reserved.CentralGuard® is a trademark of Central States® Manufacturing, Inc.Galvalume® is a registered trademark of BIEC International, Inc.
16" COVERAGE16" COVERAGE12" COVERAGE16" or 18" COVERAGE24" COVERAGE24" COVERAGE24" COVERAGE36" COVERAGE1¼"12" 9" 36" COVERAGE9" 36" COVERAGE36" COVERAGE¾"6" 36" COVERAGE36" COVERAGE28.8" COVERAGE9" 4" ⁄"⁄"¾"1"¼"½"1⁄".87"6" 1¾"2"1"½"24" or 18" COVERAGE3"3"24" or 18" COVERAGE⁄"""7.2"7.2"1 ½"1 ½"* 24 ga. available in Polar and Galvalume, acrylic-coated bare in select plants Choose CentralGuard®for the best protection anda lifetime warranty.CentralGuard is our specic combination of everything that goes into making the highest-quality metal panels. Available on our Prime panels, the CentralGuard name is a guarantee that you have the best protection and a lifetime paint warranty.Choose CentralGuard for the perfect balance of fade protection, rust blocking, and dent resistance. GAUGE 26 ga. | 24 ga.*STEEL THICKNESS 26 ga. 0.0185" | 24 ga. 0.0230"PAINT THICKNESS Top coat paint: .70 mil Top coat primer: .30 mil Bottom coat backer: .35 mil Bottom coat primer: .35 milTOTAL THICKNESS 26 ga. 0.0202" | 24 ga. 0.0247"RUST PROTECTANT SUBSTRATE Galvalume® AZ50STEEL STRENGTH 80,000 PSI (26 ga.) | 50,000 PSI (24 ga.)PAINT SYSTEM SMPWARRANTY Lifetime limited paint adhesion 30-yr. chalk and fade 50-yr. Galvalume perforationAPPROVALS UL2218 UL Approval, Impact Resistance, Class 4 UL580 UL Approval, Uplift Resistance, Class 90 UL790 UL Approval, Fire Resistance, Class A RC-445 Texas Windstorm Approval, 26 ga. min. Over Steel Purlins FL30071 Florida Approval, Roof Panel 26 ga. min. Over Steel Purlins FL14016 Florida Approval, Roof Panel 26 ga. min. Over Steel Purlins (NON-HVHZ)MINIMUMSPECIFICATIONSFOR PRIME PAINTED PANELSTESTING & APPROVALSTHRIFTYPRIMECentralGuardFADE PROTECTIONPaint Warranty 20-YEARLIFETIMEPaint Thickness THIN .70 milTHICKER 1.0 milFade Warranty –30-YEARFade ProtectionP PPRUST BLOCKINGAdvanced Rust Blocking –PPerforation Warranty –50-YEARSubstrate Thickness 1.12 mil1.60 milDENT RESISTANCEAdvanced Dent Resistance –PPSteel Thickness THINTHICKSteel Gauge 26 ga.26 ga.INSTALLATIONPurlin Bearing Leg –POUR BEST SELLER!Find more information atcentralstatesco.com
GUID_PROD_MLOC_240415D CM-Loc™Product GuideHELPFUL INFORMATION ON PANELS, TRIMS, GUTTERS AND ACCESSORIES36" COVERAGE6" 13/16"
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 3Information in this catalog may vary by plant location.Please call your salesperson to verify product availability.NOTICE: The application and detail drawings in this manual are strictly for illustration purposes and may not be applicable to all building designs or product installations. Projects should conform to local building codes. Central States Manufacturing is not responsible for the performance of the material if it is not installed correctly.Information contained in this booklet was in eect at the time of publication and is subject to change without notice.Warranties 4Panel Codes 4Section Properties / Live & Wind Loads 5Fastener Spacing 6Care and Handling 6-7Converting Pitch to Degree 8Square Conversions 9Gauge and Color Codes 10Roof Trims 11-12Wall Trims 13Gutters 14-15Accessories 16-17Secondary Framing 18-19Standard Punch Patterns 20-21INDEX
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 4PANEL PROFILE TYPE CODEM-Loc™ Prime SMP ML6(color)M-Loc™ Thrifty SMP MN6(color)THM-Loc is available in 26 ga. painted and bare Galvalume®. Prime panels come with CentralGuard® protection that includes superior dent resistance, a lifetime limited paint warranty, and a 20-year substrate warranty. Bare (non-painted) panels from Central States have an acrylic coating which eliminates using oils during manufacturing, and eliminates ngerprinting and foot marking during installation. Bare, unpainted Galvalume is not warranted for uniformity in appearance, whether it be color, sheen, or spangle. If the project requires a uniform appearance, please choose a painted product.Central States' 26 ga. steel is manufactured to meet ASTM A792 specications for galvalume with a minimum yield of 80,000 PSI. The M-Loc panel also has a Class 4 UL2218 impact resistance rating, a Class A UL790 re resistance rating, and a Class 90 UL580 uplift resistance rating.The recommended minimum roof slope for the ⁄" M-Loc is a 1:12 pitch. This will allow for sucient drainage of water. For added protection, a sealant tape can be used on the laps of the panel.WARRANTIESWARRANTIESWarranties are available in paper format and downloadable from our website. After the job is complete, ll out a warranty with your contractor/installer details and the Central States order number. Give the warranty to the building owner to keep for their records. Optional warranty registration is available online.Learn more at centralstatesco.com/warrantiesM-LOC™PANEL CODESPurlin Bearing Leg
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 5SECTION PROPERTIES36" WIDE, MLOC™ PANELSection properties and allowables are calculated in accordance with 1996 AISI Specications and 1999 AISI Supplement No. 1. I +/- is for deection determination. S +/- is for bending determination. Ma is allowable bending moment. All values are for one foot of panel width. These loads are for panel strength. Frames, purlins, fasteners and all supports must be designed to resist all loads imposed on the panel. Allowable outward loads based on stress have been increased by 33.33% for wind uplift. Allowable loads for deection are based on deection limitation of span/180 or span/240. For roof panels, self weight of the panel has to be deducted from the allowable inward load to arrive at the actual "live load" carrying capacity of the panel. Minimum bearing length must be checked. Minimum deliverable bare steel thickness should not be less than 0.95 of design thickness.Gauge26Thickness(inches)0.0185Weight(psf)0.874 Yield Stress(ksi)80.0Ixxin4/ft0.0250Sxxin3/ft0.0441Main.kips/ft1.5857Ixxin4/ft0.0170Sxxin3/ft0.0379Main.kips/ft1.3617Top in Compression(Positive Bending)Bottom in Compression(Negative Bending)Span (feet)33.544.55678LL (S)(psf)117.586.366.152.242.334.929.421.6LL (D) L/180(psf)80.951.034.124.017.513.110.16.4LL (D) L/240(psf)60.738.225.618.013.19.97.64.8WL(psf)134.198.675.559.648.339.933.524.626 Gauge & 80 ksiTheoretical allowable loads are based on uniform span lengths. LL (S) is allowable live load based on stress limitation. LL (D) is allowable live load based on deection limitation of L/180 or L/240. WL is allowable wind load and has been increased by 33.33%.SINGLE SPAN CONDITIONTHEORETICAL ALLOWABLE LIVE & WIND LOADSSpan (feet)33.544.55678LL (S)(psf)100.974.156.744.836.330.025.218.5LL (D) L/180(psf)100.966.444.531.222.817.113.28.3LL (D) L/240(psf)79.049.833.323.417.112.89.96.2WL(psf)156.2114.887.969.456.246.539.128.726 Gauge & 80 ksiTWO SPAN CONDITIONSpan (feet)33.544.55678LL (S)(psf)117.886.666.352.442.435.129.521.6LL (D) L/180(psf)117.886.664.445.333.024.819.112.0LL (D) L/240(psf)114.572.148.333.924.718.614.39.0WL(psf)182.5134.1102.781.165.754.345.633.526 Gauge & 80 ksiTHREE OR MORE SPAN CONDITION
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 6FASTENER SPACINGFastener pattern at panel termination (Eave, endlap, valley, ridge, high eave)Fastener pattern at interior of panelDELIVERY Deliveries will be made using a 65' tractor/trailer weighing approximately 80,000 lbs. It is imperative that all delivery locations be accessible by a vehicle of this size. Our drivers have the authority to refuse delivery to any location they see as unsafe or inaccessible. The customer is responsible for any charges incurred if truck is detained for any reason. The customer is responsible for unloading all trucks. Any damage that occurs at this point is the customer’s responsibility. There must be equipment available to unload the truck. Moett deliveries require at least one person to assist with unloading.STAGEGalvalume® steel panels have a good service life when exposed to normal weather conditions; however, to protect the appearance of panels and trims from damage, there are a few simple precautions that can be taken. The panels are subject to stain when water sits upon, or becomes trapped between the sheets. If the Galvalume® panels are to be stored for any period of time, they should be stored only in a dry place, preferably under a roof. Stand panels on end and fan them out at the bottom to provide air circulation and moisture run o. If space does not allow this, the panels should be separated, blocked o of the oor at least 12 inches to allow air ow, and stored at an incline to encourage drainage. The panels should then be covered, yet still have good air ow through the sheets to prevent condensation. Do not use a plastic cover, as this may cause the panels to sweat or condensation to occur.CARE AND HANDLING⁄"36" 6" 6"6" 6" 6"36" 12" 12" ⁄"⁄"36" 6" 6"6" 6" 6"36" 12" 12" ⁄"
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 7Shavings created bysaw cutting or drillingmay cause the panel to rust and will void warranties in aected areas.CAUTIONCARE AND HANDLINGSTORAGEFailure to follow these steps may result in wet storage stains and premature rusting. The manufacturers warranty will be void at this time, and the manufacturer will not be responsible.HANDLINGWhen unloading panels, extreme caution must be employed. Care needs to be used when unloading panels with a forklift. Panel edges and underside paint may become damaged if the forklift driver does not use caution. Once at the job site, care must be taken in order to protect the painted surface. When unbundling the panels, never drag them across the surface of one another. This may cause scratches across the underneath panels. It is recommended that the panels be “rolled” o the top of the bundle to prevent scratching. Never lift panels by the ends, instead lift the panels longitudinally and carry vertically.Panel edges are very sharp, therefore, safety equipment should be worn by all workers handling the material.CUTTINGA portable eld shear is the ideal method for cutting panels. Nibblers or a power shear may also be used. Although we do not recommend it, if you decide to cut with a saw, it is very important that the panels be turned upside down during cutting so that hot shavings do not come in contact with the painted surface. Make sure all adjacent panels are covered so that shavings are not imbedded in these panels. If metal shavings become imbedded in the paint surface, they will quickly rust. To avoid this, panels should be thoroughly wiped of all lings on both sides of the panel. Failure to comply with the recommended cutting procedures releases the manufacturer of any responsibility.DRILLINGPanels and trim should not be drilled while stacked. This will cause shavings that will become imbedded in the paint surface.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 8CONVERTING PITCH TO DEGREE135°1:12PITCH2:12PITCH3:12PITCH4:12PITCH5:12PITCH6:12PITCH7:12PITCH8:12PITCH9:12PITCH10:12PITCH11:12PITCH12:12PITCH94° 99° 104° 108° 112° 116° 120° 123° 126° 129° 132° 135°173° 167° 160° 154° 148° 143° 138° 134° 130° 126° 123° 120°170° 161° 152° 143° 135° 127° 120° 113° 106° 100° 95° 90°1:12PITCH2:12PITCH3:12PITCH4:12PITCH5:12PITCH6:12PITCH7:12PITCH8:12PITCH9:12PITCH10:12PITCH11:12PITCH12:12PITCH13:12PITCH14:12PITCH15:12PITCH16:12PITCH17:12PITCH18:12PITCH1:12PITCH175° 171° 166° 162° 158° 155° 151° 148° 145° 142° 140° 137° 135° 133° 132° 130° 128°2:12PITCH175° 175° 171° 167° 163° 159° 156° 153° 150° 147° 144° 142° 140° 138° 136° 135° 133°3:12PITCH171° 175° 176° 171° 167° 164° 160° 157° 154° 152° 149° 147° 145° 143° 141° 139° 138°4:12PITCH166° 171° 176° 176° 172° 168° 165° 162° 159° 156° 153° 151° 149° 147° 145° 144° 142°5:12PITCH162° 167° 171° 176° 176° 172° 169° 166° 163° 160° 158° 155° 153° 151° 149° 148° 146°6:12PITCH158° 163° 167° 172° 176° 176° 173° 170° 167° 164° 162° 159° 157° 155° 153° 152° 150°7:12PITCH155° 159° 164° 168° 172° 176° 177° 173° 170° 168° 165° 163° 161° 159° 157° 155° 154°8:12PITCH151° 156° 160° 165° 169° 173° 177° 177° 174° 171° 169° 166° 164° 162° 161° 159° 157°9:12PITCH148° 153° 157° 162° 166° 170° 173° 177° 177° 174° 172° 170° 167° 166° 164° 162° 161°10:12PITCH145° 150° 154° 159° 163° 167° 170° 174° 177° 177° 175° 173° 170° 168° 167° 165° 163°11:12PITCH142° 147° 152° 156° 160° 164° 168° 171° 174° 177° 178° 175° 173° 171° 169° 168° 166°12:12PITCH140° 144° 149° 153° 158° 162° 165° 169° 172° 175° 178° 178° 176° 174° 172° 170° 169°LOWER ROOF PITCH INCHES OF RISE OVER 12" OF RUNUPPER ROOF PITCH INCHES OF RISE OVER 12" OF RUNSINGLE SLOPE PITCHES Fascia, Eave, Endwall, Tie-In, GutterDOUBLE SLOPE PITCHES Hip, ValleyRIDGE CAPTRANSITION TRIM180°170°160°150°140°130°120°110°100°90°80°70°60°50°40°30°20°10°0°Use these charts to calculate degrees when designing custom trim.Please specify pitch when ordering. 90°Upper Transition Trim3:1210:12154°Lower Transition Trim10:123:12154°Painted sidePainted sideFind the box that intersects your lower and upper roof pitches.If the intersection landsin the gray area, select aLower Transition trim.30°
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 9COMMON RAFTER LENGTHS PEAK TO SIDEWALLFor 26 ga. panels there are 2 formulas; one for panels measured in inches and one for panels measured in feet. While the actual panel width is 38.5", there will only be 36" of coverage per panel. Squares are gured based on actual width. One square is equal to a panel 31.169 feet long. One square of metal will give you approximately 94.5 square feet of coverage. One square is equal to 14,400 square inches.38.5 (or width in inches) multiplied by length in inches multiplied by # of pieces divided by 14,40038.5" x 144" x 12 14,400Number of panels = 12Panel width = 38.5"Panel length = 144"Square inches = 14,400EXAMPLE 1:length in feet multiplied by # of piecesdivided by 31.16912 x 12 31.169Number of panels = 12Panel width = 38.5"Panel length = 12'EXAMPLE 2:equals 4.62 squares of metalequals 4.62 squares of metalRunning Feet12345678910111213141516171819202122232425262728293031323334351:12 Pitch1' 0"2' 1/8"3' 1/8"4' 1/8"5' 1/4"6' 1/4"7' 1/4"8' 3/8"9' 3/8"10' 3/8"11' 1/2"12' 1/2"13' 1/2"14' 5/8"15' 5/8"16' 5/8"17' 5/8"18' 3/4"19' 3/4"20' 7/8"21' 7/8"22' 7/8"23' 1"24' 1"25' 1"26' 1-1/8"27' 1-1/8"28' 1-1/8"29' 1-1/4"30' 1-1/4"31' 1-3/8"32' 1-3/8"33' 1-1/2"34' 1-1/2"35' 1-1/2"2:12 Pitch1' 1/8"2' 3/8"3' 1/2"4' 5/8"5' 7/8"6' 1"7' 1-1/8"8' 1-3/8"9' 1-1/2"10' 1-5/8"11' 1-7/8"12' 2"13' 2-1/8"14' 2-3/8"15' 2-1/2"16' 2-5/8"17' 2-7/8"18' 3"19' 3-1/8"20' 3-3/8"21' 3-1/2"22' 3-5/8"23' 3-3/4"24' 4"25' 4-1/8"26' 4-1/4"27' 4-1/2"28' 4-3/4"29' 4-7/8"30' 5"31' 5-1/8"32' 5-1/4"33' 5-1/2"34' 5-3/4"35' 5-7/8"3:12 Pitch1' 3/8"2' 3/4"3' 1-1/8"4' 1-1/2"5' 1-7/8"6' 2-1/4"7' 2-5/8"8'3"9' 3-3/8"10' 3-3/4"11' 4-1/8"12' 4-3/8"13' 4-3/4"14' 8-1/8"15' 5-1/2"16' 5-7/8"17' 6-1/4"18' 6-5/8"19' 7"20' 7-3/8"21' 7-3/4"22' 8-1/8"23' 8-1/2"24' 8-7/8"25' 9-1/4"26' 9-1/2"27' 9-7/8"28' 10-1/4"29' 10-5/8"30'11"31' 11-3/8"32' 11-3/4"34' 1/8"35' 1/2"36' 7/8"4:12 Pitch1' 5/8"2' 1-1/4"3' 2"4' 2-5/8"5' 3-1/4"6' 3-7/8"7' 4-1/2"8' 5-1/4"9' 5-7/8"10' 6-1/2"11' 7-1/8"12' 7-3/4"13' 8-1/2"14' 9-1/8"15' 9-3/4"16' 10-3/8"17' 11"18' 11-5/8"20' 3/8"21' 1"22' 1-5/8"23' 2-1/4"24' 3"25' 3-5/8"26' 4-1/4"27' 5"28' 5-5/8"29' 6-1/4"30' 6-7/8"31' 7-1/2"32' 8-1/8"33' 8-3/4"34' 9-3/8"35' 10"36' 10-5/8"5:12 Pitch1'1"2'2"3'3"4'4"5'5"6'6"7'7"8'8"9'9"10'10"11'11"13'0"14'1"15'2"16'3"17'4"18'5"19'6"20'7"21'8"22'9"23'10"24'11"26'0"27'1"28'2"29'3"30'4"31'5"32'6"33'7"34'8"35'9"36'10"37'11"6:12 Pitch1' 1-3/8"2' 2-7/8"3' 4-1/4"4' 5/8"5' 7-1/8"6' 8-1/2"7' 9-7/8"8' 11-3/8"10' 3/4"11' 2-1/8"12' 3-5/8"13' 5"14' 6-3/8"15' 7-7/8"16' 9-1/4"17' 10-5/8"19' 1/8"20' 1-1/2"21' 2-7/8"22' 4-3/8"23' 5-3/4"24' 7-1/8"25' 8-5/8"26' 10"27' 11-3/8"29' 3/4"30' 2-1/4"31' 3-3/4"32' 5-1/8"33' 6-1/2"34' 7-7/8"35' 9-1/436' 10-3/4"38' 1/4"39' 1-5/8"SQUARE CONVERSIONS
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 10* Longer lead times may apply. ** Copper Metallic is FEVE. FEVE = Flourinated Polymer Paint SystemGalvalume® is a registered trademark of BIEC International, Inc..HOW TO ORDER TRIMUN 6 RR TRIM GAUGE COLOR CODE CODE CODE TRIM CODEEXAMPLE: Universal Ridge Cap, 26 gauge, RusticUNIVERSAL RIDGE CAPUN - Girth 24" PAINTSTEP 1:In CentralLink™, start by entering the Item ID. Item ID is made of the TRIM CODE, a GAUGE CODE, and a COLOR CODE. The TRIM CODE can be found with each drawing next to the trim's name. The GAUGE CODE and COLOR CODES are found below.STEP 2:Then type the number of pieces you needalong with the length in feet and inches.pitchCOLOR CODESGAUGE CODE26 629 9GAUGE CODES PANEL TRIMSMP GAUGE GAUGE CODEAlamo 29 AWBlack 29 BKBrilliant 26 29/26 BIBrown 26 29/26 BRBurgundy 26 29/26 BGBurnished Slate 26 29/26 BSCharcoal 26 29/26 CHColony 26 26 CGCopper Metallic** 26 29/26 CMCrimson 26 29/26 CRDesert 26 26 DSForest 29/26 DGFern 26 26 FNGallery 26 29/26 GBGalvalume® 26 29/26 GLGalvanized 29 ZNGray 26 29/26 GAHawaiian 26 26 HBHunter 26 29/26 GRIvory 29 IVLight Stone 26 29/26 LSOcean 29 OBPewter 29 PGPolar 26 26 PWRustic 26 29/26 RRTan 26 29/26 TNTaupe 29/26 TALookupUN6RREnter Item IDPieces10Feet12Inches2Description: 26, Rustic, Universal Ridge Cap CentralLink order screen
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 11ROOF TRIMSUnless otherwise noted all angles are 90° or 45°. See page 10 for gauge and color codes.RIDGE CAP - Specify pitch.36"18"UNIVERSAL RIDGE CAPUN - Girth 24" Additional pallet charge may apply.FORMED RIDGE CAPMLFRC36 - Length 3' Specify pitch up to 5:12. Longer lead times may apply.PAINTpitchPAINTRAKE/GABLEHOUSE RAKEMLHR - Girth 12"PAINTRESIDENTIAL RIDGE CAPRRCP - Girth 17" Additional pallet charge may apply.PAINTRIDGE CAPRCP - Girth 13.75" Additional pallet charge may apply.Recommended for 6:12 or less.RAKEMLRA - Girth 20.75" RAKE PEAK BOXMLPBOXF - 2'6"Specify pitch. RAKE END CAPREND - Left hand shown.105°105°150°PAINT PAINTBOX RAKEMLBRT - Girth 20.75" BOX RAKE PEAK BOXMLPBBF - 3'Specify pitch.BOX RAKE END CAPBREND - Left hand shown.126342PAINTPAINTPAINTPAINTRESIDENTIAL RAKERRT - Girth 10.75" RAKE & CORNERCOR - Girth 13" GABLEGT6 - Girth 16.5" PAINTPAINTPAINT15⁄8"4"6 ¼"½" hempitch¾"PAINTpitch8"8"26 ga. only.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 12Unless otherwise noted all angles are 90° or 45°. See page 10 for gauge and color codes.ROOF TRIMSTRANSITION TT - Girth 12.5" TRANSITION TRIMS - Specify pitch.TRANSITIONGTL2 - Girth 14.5" PAINTPAINTHIGH SIDE PARAPETHSP - Girth 10.5"ENDWALLEW - Girth 10.25" PAINTUNIVERSAL SIDEWALLSF1- Girth 9.25"FLAT SHEETFS9 - 29 gauge. Girth 43"FS6 - 26 gauge. Girth 41.5625"10 sheets or fewer will be packaged in a roll.Additional pallet charge on orders of 10 or more.PAINTVALLEYVT1 - Girth 19.75" Intended for valley lengths less than 30'.Additional pallet charge will apply.EXTENDED VALLEYEVA- Girth 41.5" Intended for valley lengths greater than 30'.Additional pallet charge will apply.pitchPAINTVALLEY - Specify pitch.EAVE - Specify pitch.HIGH-SIDE EAVEHI - Girth 20.75" SHORT EAVESEA - Girth 9.5" LONG EAVELEA- Girth 9.5" pitchpitchpitchPAINT PAINT PAINTRESIDENTIAL EAVERET - Girth 6.5" RESIDENTIAL DRIP EDGERDC - Girth 9.5" 90° pitch if not specied. FASCIAFT - Girth 9" pitchpitchPAINT PAINTGABLE BASE SOFFITGB1 - Girth 20.25" 10.875” coveragePAINTpitchPAINTpitchPAINTPAINT
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 13Unless otherwise noted all angles are 90° or 45°. See page 10 for gauge and color codes.WALL TRIMSINSIDE CORNERIC1 - Girth 13" HEAD TRIMMLHE - Girth 5" FRAMED OPENING TRIMSJAMBMLJA - Girth 5" JAMB HEADERJH - Girth 13" 45°PAINTANGLE TRIMSINSIDE ANGLEIA2X2 - Girth 5" IA3X3 - Girth 7"IA4X4 - Girth 9"OUTSIDE ANGLESA2X2 - Girth 5" SA3X3 - Girth 7"SA4X4 - Girth 9"PAINTPAINT PAINTPAINTRAT GUARDRG - Girth 4.75" PAINT2"3" 4"2"3" 4"PAINT2"3" 4"2"3" 4"DOOR EDGEDJ10 - Girth 11.25" PAINTDOUBLE ANGLEDA1 - Girth 3.5" Use with wainscot.PAINTWIDE DOUBLE ANGLEDA2 - Girth 4.5" Use with wainscot.PAINTJ-TRIMJT - Girth 4.8125" PAINTWINDOW DRIP CAPWC - Girth 3.75" PAINTPOST TRIMSA312 - Girth 5.5" SA512 - Girth 7.5"SA7 - Girth 9"SA712 - Girth 9.5"PAINTRAKE & CORNERCOR - Girth 13" MINI CORNERMCRN - Girth 9.5" PAINT PAINTBASE ANGLEMLBA - Girth 5.375" 3 ¼"5⁄8"1"PAINT
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 14GUTTERS378"338"ROOF PANELINSIDE CLOSUREEAVE TRIM45° ELBOWBUTYL TAPEBUTYL TAPEGUTTERDOWNSPOUTFIELD CUT & BEND OUTLET(SEAL CONNECTION AND FASTENWITH POP RIVETS)IN BOTTOM OF GUTTER#12 X 7/8" LAP(2 PER GUTTER STRAP)GUTTER STRAP(36" O.C.)#12 X 7/8" LAP (12" O.C.)DOWNSPOUT OUTLETDOWNSPOUT STRAPDOWNSPOUT SLEEVE45° ELBOWDOWNSPOUT SLEEVESLEEVE (TYP)SLEEVE (TYP)45° ELBOWSLEEVE (TYP)SOFFIT PANEL
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 15Unless otherwise noted all angles are 90° or 45°. See page 10 for gauge and color codes.GUTTERSHANG-ON 0-4:12 PITCHMLGU - Girth 21.50" HANG-ON 5:12 PITCHMLGU5 - Girth 22.9375" HANG-ON 6:12 PITCHMLGU6 - Girth 23.1875" 4"4"4"¾"1"150°105°½"hem123°pitchpitch7 ¼"EAVE 0-4:12 PITCHMLSGU - Girth 24.25" EAVE 5:12 PITCHMLSGU5- Girth 26.1875" 4"4"4"1"4"150°105°½"hem123°pitchpitch7¼"EAVE 6:12 PITCHMLSGU6 - Girth 26.4375" PAINTSCULPTURED GUTTERSBOX GUTTERS - Dimension "A" will change depending on chosen pitch. 4"4"4"¾"1"½"hemroofpitchroofpitch150°105°8 ⁄”PAINT PAINTPAINT150°½"hem4"4"4"1"4"105°roofpitchroofpitch8 ⁄”PAINT PAINTHANG-ONPAINTMLBHG1 1:12 18.0625" 4.8125"MLBHG2 2:12 18.5625" 5.3125" MLBHG3 3:12 19" 5.75"MLBHG4 4:12 19.5" 6.25"MLBHG5 5:12 19.9375" 6.6875"MLBHG6 6:12 20.4375" 7.1875"PART # PITCH GIRTH DIM. “A”BOX EAVEMLBEG1 1:12 21.3125" 4.8125"MLBEG2 2:12 21.8125" 5.3125" MLBEG3 3:12 22.25 5.75MLBEG4 4:12 22.75" 6.25"MLBEG5 5:12 23.1875" 6.6875"MLBEG6 6:12 23.6875" 7.1875"PART # PITCH GIRTH DIM. “A”PAINT4"4"4"¾"1"½"hemroofpitchroofpitch150°105°8 ⁄”150°½"hem4"4"4"1"4"105°roofpitchroofpitch8 ⁄”DOWNSPOUTSOUTSIDE CORNER BOXOCB - Specify pitch. INSIDE CORNER BOXICB - Girth 25.6875" PAINTUse with sculptured gutters.PAINTUse with sculptured gutters.(left or right)(left)DOWNSPOUT- Length 16" DS - straightDK - with kickoutDOWNSPOUT STRAPDSSDOWNSPOUT OUTLETDSOUTLETSpecify pitch. 1/2" turndowns.3 ½"3 ½"4"4"4"3 ½"DOWNSPOUT ELBOWDSE45DSE90GUTTER STRAPMLGS9631/2"2"41/4"SCULPTURED GUTTER END CAPMLGEN - Specify pitch and left or right.Left or right as you are on the ground looking at the gutter expanse from the eave.135°±9"1"1 "DOWNSPOUT CONNECTORDSLVE(right)3 ½"3 ½"4"4"4"3 ½"PAINT PAINTBOX GUTTER END CAPBGEN - Specify pitch.PAINTDS DK
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 16TYPE PART # LENGTH DIAMETER HEAD COLOR #BAGMETAL/METAL 114(color)MM 1 1/4" #12 5/16" Hex all 250METAL/METAL 2ZMM 2" #12 5/16" Hex galvanized 250METAL/METAL LAP 78(color)LAP 7/8" #14 5/16" Hex all 250ZAC METAL/METAL 114ZACMM 1 1/4" #12 5/16" Hex galvanized 250ZAC METAL/METAL LAP 78ZACLAP 7/8" #14 5/16" Hex galvanized 250Fastener color availability may vary by location, contact your sales consultant for details. Order fasteners in increments of 250 pieces.FASTENERSACCESSORIESDOOR SET - With steel jamb, knob sold separately.3068DR - 38" x 81 ⁄"4068DR - 50" x 81 ⁄"DOOR LEAF - Steel door leaf only.3070DOOR - 3 x 7'3070DOORW/LITE - 3' x 7' with window.4070DOOR - 4' x 7'DOOR KNOB KNOBCOVERAGE 36"1"118"118"78"78"55°55°DOORS & FRAMING PACKAGE - Longer lead times may apply.FRAMING PACKAGE - White.4X3070JAMB - 4.25" x 30704X4070JAMB - 4.25" x 40706X3070JAMB - 6.25" x 30706X4070JAMB - 6.25" x 40708X3070JAMB - 8.25" x 30708X4070JAMB - 8.25" x 40708X6070JAMB - 8.25" x 6070 Package includes: Jambs, headers, threshold, door lever with keyed lock, hinges, and weather strip kit. Frames are non-reversable. Swing-out only.PAINTWhite FiberglassMLSKYW12 - Length 12'.SKYLIGHTS For best results, use approved sealant (MRS10SKY), Skylight Trim (MLSK) and washer (118WASHER). Skylights should be predrilled.Skylight Washer - White.118WASHER - ⁄" outside diameter, ¼" inside diameter100 per bag.Skylight Sealant - Clear.MRS10SKY - 10.3 oz. tubeApproved for skylight use.Skylight TrimMLSK - Girth 5".Skylight Ridge Cap - UniversalRCPCC10 - Clear PolycarbonateRCPCW10 - White PolycarbonateLength 10'6"'. Width 25". 6 1⁄8"¾"¾"3 ½"2 1⁄8"
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 17ACCESSORIESOUTSIDE CLOSUREMLCLOUT - No Glue. MLCLOUTGLUE - With Glue. CLOSURESLength - 3'. 100 per box.INSIDE CLOSUREMLCLIN - No Glue. MLCLINGLUE - With Glue. Length - 3'. 100 per box.CLOSURE VENTMLCLVLength - 3'. 25 rolls per box.Closure is 1 1/8" tall and may require longer screws for installation. Item may vary from sample shown. BUTYL TAPEInstall between fastener and exposed edge.Rolls per box may vary by location and vendor. Check with your sales consultant for details.BTL 45' 3/4" 3/32" 24BTR 40' 7/8" 3/16" 10BT3/8 45' 3/8" 3/32" 40Recommended for M-Loc.TOUCH UP PAINTTP(color) - SMP, 0.6 oz. bottle w/brush.12PURSP - Purlin paint. 12 oz. spray.PART # LENGTH WIDTH THICKNESS ROLLS PER BOXSEALANTPART # SIZE COLORGEO(color) 10.3 oz. tube clear, gray, whiteMRS10(color) 10.3 oz. tube call for colorsMRS10CLEAR 10.3 oz. tube clearSquare - Max temperature 250°.MPF - Pipe size .25" to 5.75" MPF2 - Pipe size .875" to 4"MPF4 - Pipe size 2.75" to 7"MPF6 - Pipe size 4.75" to 10"MPF8 - Pipe size 6.75" to 13.5"MASTER PIPE FLASHING - Install in a diamond shape and not parallel to the rib.Silicone - Orange, high temp max 500°.4SMPF - Pipe size 2.75" to 7"6SMPF - Pipe size 4.75" to 10"8SMPF - Pipe size 6.75" to 13.5"Square with zipper - Max temperature 250°.MPF1ZIP - Pipe size .5" - 4"MPF2ZIP - Pipe size 4" - 9.25"UNIVERSAL POLYFOAMPOLYG - With Glue. 10-rolls per box.Length 25'. Width 1 1/2". Thickness 1 1/2". GRAYFLEXGRAYFLEX-6 - 24-rolls per box.Length 20'. Width 1". Thickness 1". For use with hips and valleys. FLEXOVENTFLEXOVENT - (2) 10' rolls per box.Length 10'. Width 3". Thickness 1 1/2".
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 18Members can be manufactured to the nearest 1/8" in length from 6'0" to 45'0". For lengths under 6'0" or over 45'0", call your sales consultant.SECONDARY FRAMINGSingle Slope Up Single Slope Down Double Slope Up Double Slope DownCentral States has met the requirements to earn the accreditation for Cold-Formed Steel Structural and non-Structural Components Not Requiring Welding For more information, go to www.iasonline.org.2521834312134.50" .50" 1.25" 1.50" ANGLE CHANNEL CEE LGSI ZEE ZEEEAVE STRUTSMINI CLIPMINICLIP- 16 gauge.PURLIN CLIPSBASE CLIPBASECLIP- 14 gauge.Galvanized.HAT20Z202 - 20'2" length, 20 gauge, galvanized.HAT20Z - Specify length, 20 gauge, galvanized.HAT16Z - Specify length, 16 gauge, galvanized.HAT CHANNEL* Specify pitch and slope when ordering. For low pitch (up to 4:12) add a "L" to the end of the code. For high pitch (5:12 and above) add a "H" to the end of the code.7241453413437878GIRT CLIPGIRTCLIP - 10 gauge.GIRTCLIPZ - 10 gauge.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 19SECONDARY FRAMING ITEM CODE ITEM CODETYPE A x B GAUGE RED OXIDE GALVANIZEDAngle 2.5 x 2.5 14 B2514RAngle 3 x 3 16 B316R B316ZAngle 3 x 3 14 B314R B314ZAngle 4 x 2 16 B4216R B4216ZAngle 4 x 2 14 B4214R B4214ZAngle 4 x 3 16 B4316RTYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDChannel 4.25 x 2.35 x 2.35 16 U4216R U4216ZChannel 4.25 x 2.85 x 2.85 16 U42516R U42516ZChannel 4.25 x 2.85 x 2.85 14 U42514R U42514ZChannel 4.25 x 2.85 x 2.85 12 U42512R U42512ZChannel 6.25 x 2.85 x 2.85 16 U62516R U62516ZChannel 6.25 x 2.85 x 2.85 14 U62514R U62514ZChannel 8.25 x 2.85 x 2.85 16 U82516R U82516ZChannel 8.25 x 2.85 x 2.85 14 U82514R U82514ZChannel 8.25 x 2.85 x 2.85 12 U82512R U82512ZTYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDEave Strut 6 x 4 x 3 16 E64316R* E64316Z*Eave Strut 6 x 4 x 3 14 E64314R* E64314Z*Eave Strut 6 x 4 x 3 12 E64312R* E64312Z*Eave Strut 8 x 4 x 3 14 E84314R* E84314Z*Eave Strut 8 x 4 x 3 12 E84312R* E84312Z*Eave Strut 8 x 5 x 3 14 E85314R* E85314Z*Eave Strut 8 x 5 x 3 12 E85312R* E85312Z*Eave Strut 8 x 5 x 5 14 E85514R*Eave Strut 10 x 5 x 3 14 E105314R*TYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDCEE 4 x 2 x 2 16 C4216R C4216ZCEE 4 x 2.5 x 2.5 16 C42516R C42516ZCEE 4 x 2.5 x 2.5 14 C42514R C42514ZCEE 4 x 2.5 x 2.5 12 C42512R C42512ZCEE 4 x 3.5 x 3.5 16 C43516R C43516ZCEE 4 x 3.5 x 3.5 14 C43514R C43514ZCEE 6 x 2.5 x 2.5 16 C62516R C62516ZCEE 6 x 2.5 x 2.5 14 C62514R C62514ZCEE 8 x 2.5 x 2.5 16 C82516R C82516ZCEE 8 x 2.5 x 2.5 14 C82514R C82514ZCEE 8 x 2.5 x 2.5 12 C82512R C82512ZCEE 8 x 3.5 x 3.5 16 C83516R C83516ZCEE 8 x 3.5 x 3.5 14 C83514R C83514ZCEE 8 x 3.5 x 3.5 12 C83512R C83512ZCEE 9 x 3 x 3 14 C9314R C9314ZCEE 9 x 3 x 3 12 C9312R C9312ZCEE 10 x 2.5 x 2.5 16 C102516R C102516ZCEE 10 x 2.5 x 2.5 14 C102514R C102514ZCEE 10 x 2.5 x 2.5 12 C102512R C102512ZCEE 10 x 3.5 x 3.5 14 C103514R C103514ZCEE 10 x 3.5 x 3.5 12 C103512R C103512ZCEE 12 x 2.5 x 2.5 14 C122514R C122514ZCEE 12 x 2.5 x 2.5 12 C122512R C122512ZCEE 12 x 3.5 x 3.5 14 C123514R C123514ZCEE 12 x 3.5 x 3.5 12 C123512R C123512ZCEE 12 x 4 x 4 16 C12416R C12416Z ITEM CODE ITEM CODETYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDLGSI ZEE 6 x 2⁄ x 2⁄ 16 Z62516R Z62516ZLGSI ZEE 6 x 2⁄ x 2⁄ 14 Z62514R Z62514ZLGSI ZEE 8 x 2⁄ x 2⁄ 16 Z82516R Z82516ZLGSI ZEE 8 x 2⁄ x 2⁄ 14 Z82514R Z82514ZLGSI ZEE 8 x 2⁄ x 2⁄ 12 Z82512R Z82512ZLGSI ZEE 8 x 3⁄ x 3⁄ 16 Z83516R Z83516ZLGSI ZEE 8 x 3⁄ x 3⁄ 14 Z83514R Z83514ZLGSI ZEE 8 x 3⁄ x 3⁄ 12 Z83512R Z83512ZLGSI ZEE 10 x 2⁄ x 2⁄ 16 Z102516R Z102516ZLGSI ZEE 10 x 2⁄ x 2⁄ 14 Z102514R Z102514ZLGSI ZEE 10 x 2⁄ x 2⁄ 12 Z102512R Z102512ZLGSI ZEE 10 x 2⁄ x 2⁄ 14 Z10314R Z10314ZLGSI ZEE 10 x 2⁄ x 2⁄ 12 Z10312RLGSI ZEE 12 x 2⁄ x 2⁄ 14 Z122514R Z122514ZLGSI ZEE 12 x 2⁄ x 2⁄ 12 Z122512R Z122512ZLGSI ZEE 12 x 3⁄ x 3⁄ 14 Z123514R Z123514ZLGSI ZEE 12 x 3⁄ x 3⁄ 12 Z123512R Z123512ZLGSI ZEE 12 x 3⁄ x 3⁄ 16 Z12416R Z12416ZTYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDZEE 4 x 2 x 2 16 Z4216R Z4216ZZEE 4 x 2.5 x 2.5 16 Z42516R Z42516ZZEE 4 x 2.5 x 2.5 14 Z42514R Z42514ZZEE 4 x 2.5 x 2.5 12 Z42512R Z42512ZZEE 4 x 3.5 x 3.5 16 Z43516R Z43516ZZEE 4 x 3.5 x 3.5 14 Z43514R Z43514ZZEE 6 x 2.5 x 2.5 16 Z62516R Z62516ZZEE 6 x 2.5 x 2.5 14 Z62514R Z62514ZZEE 8 x 2.5 x 2.5 16 Z82516R Z82516ZZEE 8 x 2.5 x 2.5 14 Z82514R Z82514ZZEE 8 x 2.5 x 2.5 12 Z82512R Z82512ZZEE 8 x 3.5 x 3.5 16 Z83516R Z83516ZZEE 8 x 3.5 x 3.5 14 Z83514R Z83514ZZEE 8 x 3.5 x 3.5 12 Z83512R Z83512ZZEE 9 x 3 x 3 14 Z9314R Z9314ZZEE 9 x 3 x 3 12 Z9312R Z9312ZZEE 10 x 2.5 x 2.5 16 Z102516R Z102516ZZEE 10 x 2.5 x 2.5 14 Z102514R Z102514ZZEE 10 x 2.5 x 2.5 12 Z102512R Z102512ZZEE 10 x 3.5 x 3.5 14 Z103514R Z103514ZZEE 10 x 3.5 x 3.5 12 Z103512R Z103512ZZEE 12 x 2.5 x 2.5 14 Z122514R Z122514ZZEE 12 x 2.5 x 2.5 12 Z122512R Z122512ZZEE 12 x 3.5 x 3.5 14 Z123514R Z123514ZZEE 12 x 3.5 x 3.5 12 Z123512R Z123512ZZEE 12 x 4 x 4 16 Z12416R Z12416Z *For low pitch (up to 4:12) add a "L" to the end of the code. For high pitch (5:12 and above) add a "H" to the end of the code.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 20FLANGE PATTERNS - Punches can be placed on either or both ends.EAVE STRUT FOR 4" LEGES4EAVE STRUT FOR 5" LEGES5 EAVE STRUT FOR 5" LEGES134PATTERN D - OPTIONAL FLANGEPPDUse with web pattern A.PATTERN E - OPTIONAL FLANGEPPEUse with web pattern B.PATTERN F - OPTIONAL FLANGEPPFUse with web pattern C.Punch capabilities vary by location. Call for pricing and availability on special punching.Punches cannot be made on secondary framing members shorter than 3".Holes are punched to accommodate 1/2" diameter bolts.STANDARD PUNCH PATTERNSStandard hole sizes:LOCATION⁄” ROUND ⁄” ROUND ⁄” x ¾” SLOTLowell X X XJasper X XCedar Hill X XSeguin X XClaysburg X X
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 21END PUNCHPPEPPATTERN H STANDARD WEB ENDPPHSIMPLE SPAN PUNCHPPSS Minimum part length 5' total, 2'6" one end.SHORT LAP PUNCHPPSLMinimum part length 5'6" total, 2'8" one end.LONG LAP PUNCHPPLLMinimum part length 7' total, 3'6" one end.WEB PATTERNS - Punches can be placed on either or both ends.STANDARD PUNCH PATTERNSPATTERN A - STANDARD WEB - 9' Minimum length if punched on both ends; 4'6" if punched on one end.PPAPATTERN B - STANDARD WEB - 12'5" Minimum length if punched on both ends; 6'2.5" if punched on one end.PPBPATTERN C - STANDARD WEB - 7' Minimum length if punched on both ends; 3'6" if punched on one end.PPC
CENTRAL STATES MANUFACTURING, INC.Effective 05/2021 • Information subject to change 22NOTES
R-Loc™Commercial Roof and Wall PanelCENTRALSTATESCO.COMFLYR_RLOC_240412• Industry standard conguration allows maximum purlin spacing for a cost-eective building.• Ideal for low-pitch commercial roofs.• Matching trims and accessories are available.Commonly referred to as PBR-panel, this 26-gauge commercial panel is an outstanding choice for any project that requires commercial- grade performance. R-Loc is designed to maximize the potential of your structure, specically the steel frame. With the added purlin bearing leg, R-Loc provides easier installation and a more pleasing appearance.Strong and durable, fortoday’s commercial market36"OVERALLCOVERAGE1¼"MAXIMUMRIB HEIGHT½:12PITCHAND ABOVE 1¼" 36" COVERAGE12" RECOMMENDEDEC26GAUGECopyright © 2024, Central States Manufacturing, Inc., All Rights Reserved.CentralGuard® is a trademark of Central States® Manufacturing, Inc.Galvalume® is a registered trademark of BIEC International, Inc.
16" COVERAGE16" COVERAGE12" COVERAGE16" or 18" COVERAGE24" COVERAGE24" COVERAGE24" COVERAGE36" COVERAGE1¼"12" 9" 36" COVERAGE9" 36" COVERAGE36" COVERAGE¾"6" 36" COVERAGE36" COVERAGE28.8" COVERAGE9" 4" ⁄"⁄"¾"1"¼"½"1⁄".87"6" 1¾"2"1"½"24" or 18" COVERAGE3"3"24" or 18" COVERAGE⁄"""7.2"7.2"1 ½"1 ½"* 24 ga. available in Polar and Galvalume, acrylic-coated bare in select plants Choose CentralGuard®for the best protection anda lifetime warranty.CentralGuard is our specic combination of everything that goes into making the highest-quality metal panels. Available on our Prime panels, the CentralGuard name is a guarantee that you have the best protection and a lifetime paint warranty.Choose CentralGuard for the perfect balance of fade protection, rust blocking, and dent resistance. GAUGE 26 ga. | 24 ga.*STEEL THICKNESS 26 ga. 0.0185" | 24 ga. 0.023"PAINT THICKNESS Top coat paint: .70 mil Top coat primer: .30 mil Bottom coat backer: .35 mil Bottom coat primer: .35 milTOTAL THICKNESS 26 ga. 0.0202" | 24 ga. 0.0247"RUST PROTECTANT SUBSTRATE Galvalume® AZ50STEEL STRENGTH 80,000 PSI (26 ga.) | 50,000 PSI (24 ga.)PAINT SYSTEM SMPWARRANTY Lifetime limited paint adhesion 30-yr. chalk and fade 50-yr. Galvalume perforationTESTING AISI S907 Diaphragm Shear Cantilever Test, 26 ga. ASTM-E455 Diaphragm Shear Standard Test, 26 ga. ASTM-E1592 Structural Test for Roof Systems Over Open Purlin, 26 ga. ASTM-E1592 Structural Test for Roof Systems Over Solid Decking, 26 ga. ASTM-E1646 Water Leakage Test of Exterior Metal Roof Panel, 26 ga. FM4471 Foot Trac Resistance Test, 26 ga.APPROVALS UL2218 UL Approval, Impact Resistance, Class 4 UL580 UL Approval, Uplift Resistance, Class 90 UL790 UL Approval, Fire Resistance, Class A RC-424 Texas Windstorm Approval, 26 ga. min. Over Steel Purlins RC-576 Texas Windstorm Approval, 26 ga. min. Over Plywood Deck, OSB Deck, or Wood Purlins FL14024 Florida Approval, Wall Panel 26 ga. min. Over Steel Purlins (NON-HVHZ) FL14016 Florida Approval, Roof Panel 26 ga. min. Over Steel Purlins (NON-HVHZ) FL14026 Florida Approval, Roof Panel 26 ga. min. Over ⁄" Plywood (NON-HVHZ)MINIMUMSPECIFICATIONSFOR PRIME PAINTED PANELSTESTING & APPROVALSFind more information atcentralstatesco.comTHRIFTYPRIMECentralGuardFADE PROTECTIONPaint Warranty 20-YEARLIFETIMEPaint Thickness THIN .70 milTHICK 1.0 milFade Warranty –30-YEARFade ProtectionP PRUST BLOCKINGAdvanced Rust Blocking –PPerforation Warranty –50-YEARSubstrate Thickness 1.12 mil1.60 milDENT RESISTANCEAdvanced Dent Resistance –PPSteel Thickness THINTHICKSteel Gauge 26 ga.26 ga.INSTALLATIONPurlin Bearing Leg –P OUR BEST SELLER!
GUID_PROD_RLOC_240415D CR-Loc™Product GuideHELPFUL INFORMATION ON PANELS, TRIMS, PURLINS, GUTTERS AND ACCESSORIES 1¼" 36" COVERAGE12"
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 3Information in this catalog may vary by plant location.Please call your salesperson to verify product availability.NOTICE: The application and detail drawings in this manual are strictly for illustration purposes and may not be applicable to all building designs or product installations. Projects should conform to local building codes. Central States Manufacturing is not responsible for the performance of the material if it is not installed correctly.Information contained in this booklet was in eect at the time of publication and is subject to change without notice.Warranties 4Panel Codes 4Section Properties / Live & Wind Loads 5Fastener Spacing 6Care and Handling 6-7Converting Pitch to Degree 8Square Conversions 9Gauge and Color Codes 10Roof Trims 11-12Wall Trims 13Gutters 14-15Accessories 16-17Interior Hallways 18-19Secondary Framing 20-21Standard Punch Patterns 22-23INDEX
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 4PANEL PROFILE TYPE CODER-Loc™ Prime SMP RL6(color)R-Loc™ Thrifty SMP RN6(color)THR-Loc is available in Prime 26 gauge with purlin bearing leg; in painted or bare Galvalume®. Prime panels feature CentralGuard® protection and a lifetime paint warranty. R-Loc is also available in limited colors of Thrifty 26 gauge, no purlin bearing leg, and a 20-year paint warranty. CentralGuard is our specic combination of everything that goes into making the highest-quality metal panels. Choose CentralGuard for the perfect balance of fade protection, rust blocking, and dent resistance. Bare (unpainted) Galvalume® panels from Central States have an acrylic coating which eliminates using oils during manufacturing and eliminates ngerprinting and foot marking during installation.The minimum roof slope for the 1¼" R-Loc is a ½:12 pitch. This will allow for sucient drainage of water. For added protection, a sealant tape can be used on the panel laps.WARRANTIESWARRANTIESWarranties are available in paper format and downloadable from our website. After the job is complete, ll out a warranty with your contractor/installer details and the Central States order number. Give the warranty to the building owner to keep for their records. Optional warranty registration is available online.Learn more at centralstatesco.com/warrantiesR-LOC™PANEL CODESPurlin Bearing Leg
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 5SECTION PROPERTIESTHEORETICAL ALLOWABLE LIVE & WIND LOADS36" WIDE, RLOC™ PANELSection properties and allowables are calculated in accordance with 1996 AISI Specications and 1999 AISI Supplement No. 1. I +/- is for deection determination. S +/- is for bending determination. Ma is allowable bending moment. All values are for one foot of panel width. These loads are for panel strength. Frames, purlins, fasteners and all supports must be designed to resist all loads imposed on the panel. Allowable outward loads based on stress have been increased by 33.33% for wind uplift. Allowable loads for deection are based on deection limitation of span/180 or span/240. For roof panels, self weight of the panel has to be deducted from the allowable inward load to arrive at the actual "live load" carrying capacity of the panel. Minimum bearing length must be checked. Minimum deliverable bare steel thickness should not be less than 0.95 of design thickness.Gauge26Thickness(inches)0.0185Weight(psf)0.881Yield Stress(ksi)80.0Ixxin4/ft0.0400Sxxin3/ft0.0406Main.kips/ft1.4590Ixxin4/ft0.0373Sxxin3/ft0.0497Main.kips/ft1.7847Top in Compression(Positive Bending)Bottom in Compression(Negative Bending)Span (feet)33.544.55678LL (S)(psf)108.179.460.848.038.927.019.915.2LL (D) L/180(psf)108.179.454.638.428.016.210.26.8LL (D) L/240(psf)97.161.241.028.821.012.17.65.1WL(psf)175.8129.298.978.163.344.032.324.726 Gauge & 80 ksiTheoretical allowable loads are based on uniform span lengths. LL (S) is allowable live load based on stress limitation. LL (D) is allowable live load based on deection limitation of L/180 or L/240. WL is allowable wind load and has been increased by 33.33%.SINGLE SPAN CONDITIONSpan (feet)33.544.55678LL (S)(psf)132.297.174.458.847.633.024.318.6LL (D) L/180(psf)132.297.171.150.036.421.113.38.9LL (D) L/240(psf)126.579.653.337.527.315.810.06.7WL(psf)143.7105.680.963.951.735.926.420.226 Gauge & 80 ksiTWO SPAN CONDITIONSpan (feet)33.544.55678LL (S)(psf)154.4113.586.968.655.638.628.421.7LL (D) L/180(psf)154.4113.586.968.652.830.519.212.9LL (D) L/240(psf)154.4113.577.354.339.622.914.49.7WL(psf)167.9123.494.574.660.542.030.823.626 Gauge & 80 ksiTHREE OR MORE SPAN CONDITION
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 6FASTENER SPACING19211At Intermediate SupportAt Eave or EndlapAt Trim at Roof19211At Intermediate SupportAt Eave or EndlapAt Trim at RoofFastener pattern at panel termination (Eave, endlap, valley, ridge, high eave)Fastener pattern at interior of panelDELIVERY Deliveries will be made using a 65' tractor/trailer weighing approximately 80,000 lbs. It is imperative that all delivery locations be accessible by a vehicle of this size. Our drivers have the authority to refuse delivery to any location they see as unsafe or inaccessible. The customer is responsible for any charges incurred if truck is detained for any reason. The customer is responsible for unloading all trucks. Any damage that occurs at this point is the customer’s responsibility. There must be equipment available to unload the truck. Moett deliveries require at least one person to assist with unloading.STAGEGalvalume® steel panels have a good service life when exposed to normal weather conditions; however, to protect the appearance of panels and trims from damage, there are a few simple precautions that can be taken. The panels are subject to stain when water sits upon, or becomes trapped between the sheets. If the Galvalume® panels are to be stored for any period of time, they should be stored only in a dry place, preferably under a roof. Stand panels on end and fan them out at the bottom to provide air circulation and moisture run o. If space does not allow this, the panels should be separated, blocked o of the oor at least 12 inches to allow air ow, and stored at an incline to encourage drainage. The panels should then be covered, yet still have good air ow through the sheets to prevent condensation. Do not use a plastic cover, as this may cause the panels to sweat or condensation to occur.CARE AND HANDLING
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 7Shavings created bysaw cutting or drillingmay cause the panel to rust and will void warranties in aected areas.CAUTIONCARE AND HANDLINGSTORAGEFailure to follow these steps may result in wet storage stains and premature rusting. The manufacturers warranty will be void at this time, and the manufacturer will not be responsible.HANDLINGWhen unloading panels, extreme caution must be employed. Care needs to be used when unloading panels with a forklift. Panel edges and underside paint may become damaged if the forklift driver does not use caution. Once at the job site, care must be taken in order to protect the painted surface. When unbundling the panels, never drag them across the surface of one another. This may cause scratches across the underneath panels. It is recommended that the panels be “rolled” o the top of the bundle to prevent scratching. Never lift panels by the ends, instead lift the panels longitudinally and carry vertically.Panel edges are very sharp, therefore, safety equipment should be worn by all workers handling the material.CUTTINGA portable eld shear is the ideal method for cutting panels. Nibblers or a power shear may also be used. Although we do not recommend it, if you decide to cut with a saw, it is very important that the panels be turned upside down during cutting so that hot shavings do not come in contact with the painted surface. Make sure all adjacent panels are covered so that shavings are not imbedded in these panels. If metal shavings become imbedded in the paint surface, they will quickly rust. To avoid this, panels should be thoroughly wiped of all lings on both sides of the panel. Failure to comply with the recommended cutting procedures releases the manufacturer of any responsibility.DRILLINGPanels and trim should not be drilled while stacked. This will cause shavings that will become imbedded in the paint surface.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 8CONVERTING PITCH TO DEGREE135°1:12PITCH2:12PITCH3:12PITCH4:12PITCH5:12PITCH6:12PITCH7:12PITCH8:12PITCH9:12PITCH10:12PITCH11:12PITCH12:12PITCH94° 99° 104° 108° 112° 116° 120° 123° 126° 129° 132° 135°173° 167° 160° 154° 148° 143° 138° 134° 130° 126° 123° 120°170° 161° 152° 143° 135° 127° 120° 113° 106° 100° 95° 90°1:12PITCH2:12PITCH3:12PITCH4:12PITCH5:12PITCH6:12PITCH7:12PITCH8:12PITCH9:12PITCH10:12PITCH11:12PITCH12:12PITCH13:12PITCH14:12PITCH15:12PITCH16:12PITCH17:12PITCH18:12PITCH1:12PITCH175° 171° 166° 162° 158° 155° 151° 148° 145° 142° 140° 137° 135° 133° 132° 130° 128°2:12PITCH175° 175° 171° 167° 163° 159° 156° 153° 150° 147° 144° 142° 140° 138° 136° 135° 133°3:12PITCH171° 175° 176° 171° 167° 164° 160° 157° 154° 152° 149° 147° 145° 143° 141° 139° 138°4:12PITCH166° 171° 176° 176° 172° 168° 165° 162° 159° 156° 153° 151° 149° 147° 145° 144° 142°5:12PITCH162° 167° 171° 176° 176° 172° 169° 166° 163° 160° 158° 155° 153° 151° 149° 148° 146°6:12PITCH158° 163° 167° 172° 176° 176° 173° 170° 167° 164° 162° 159° 157° 155° 153° 152° 150°7:12PITCH155° 159° 164° 168° 172° 176° 177° 173° 170° 168° 165° 163° 161° 159° 157° 155° 154°8:12PITCH151° 156° 160° 165° 169° 173° 177° 177° 174° 171° 169° 166° 164° 162° 161° 159° 157°9:12PITCH148° 153° 157° 162° 166° 170° 173° 177° 177° 174° 172° 170° 167° 166° 164° 162° 161°10:12PITCH145° 150° 154° 159° 163° 167° 170° 174° 177° 177° 175° 173° 170° 168° 167° 165° 163°11:12PITCH142° 147° 152° 156° 160° 164° 168° 171° 174° 177° 178° 175° 173° 171° 169° 168° 166°12:12PITCH140° 144° 149° 153° 158° 162° 165° 169° 172° 175° 178° 178° 176° 174° 172° 170° 169°LOWER ROOF PITCH INCHES OF RISE OVER 12" OF RUNUPPER ROOF PITCH INCHES OF RISE OVER 12" OF RUNSINGLE SLOPE PITCHES Fascia, Eave, Endwall, Tie-In, GutterDOUBLE SLOPE PITCHES Hip, ValleyRIDGE CAPTRANSITION TRIM180°170°160°150°140°130°120°110°100°90°80°70°60°50°40°30°20°10°0°Use these charts to calculate degrees when designing custom trim.Please specify pitch when ordering. 90°Upper Transition Trim3:1210:12154°Lower Transition Trim10:123:12154°Painted sidePainted sideFind the box that intersects your lower and upper roof pitches.If the intersection landsin the gray area, select aLower Transition trim.30°
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 9SQUARE CONVERSIONSCOMMON RAFTER LENGTHS PEAK TO SIDEWALLFor 26 ga. panels there are 2 formulas; one for panels measured in inches and one for panels measured in feet. While the actual panel width is 38.5", there will only be 36" of coverage per panel. Squares are gured based on actual width. One square is equal to a panel 31.169 feet long. One square of metal will give you approximately 94.5 square feet of coverage. One square is equal to 14,400 square inches.38.5 (or width in inches) multiplied by length in inches multiplied by # of pieces divided by 14,40038.5" x 144" x 12 14,400Number of panels = 12Panel width = 38.5"Panel length = 144"Square inches = 14,400EXAMPLE 1:length in feet multiplied by # of piecesdivided by 31.16912 x 12 31.169Number of panels = 12Panel width = 38.5"Panel length = 12'EXAMPLE 2:equals 4.62 squares of metalequals 4.62 squares of metalRunning Feet12345678910111213141516171819202122232425262728293031323334351:12 Pitch1' 0"2' 1/8"3' 1/8"4' 1/8"5' 1/4"6' 1/4"7' 1/4"8' 3/8"9' 3/8"10' 3/8"11' 1/2"12' 1/2"13' 1/2"14' 5/8"15' 5/8"16' 5/8"17' 5/8"18' 3/4"19' 3/4"20' 7/8"21' 7/8"22' 7/8"23' 1"24' 1"25' 1"26' 1-1/8"27' 1-1/8"28' 1-1/8"29' 1-1/4"30' 1-1/4"31' 1-3/8"32' 1-3/8"33' 1-1/2"34' 1-1/2"35' 1-1/2"2:12 Pitch1' 1/8"2' 3/8"3' 1/2"4' 5/8"5' 7/8"6' 1"7' 1-1/8"8' 1-3/8"9' 1-1/2"10' 1-5/8"11' 1-7/8"12' 2"13' 2-1/8"14' 2-3/8"15' 2-1/2"16' 2-5/8"17' 2-7/8"18' 3"19' 3-1/8"20' 3-3/8"21' 3-1/2"22' 3-5/8"23' 3-3/4"24' 4"25' 4-1/8"26' 4-1/4"27' 4-1/2"28' 4-3/4"29' 4-7/8"30' 5"31' 5-1/8"32' 5-1/4"33' 5-1/2"34' 5-3/4"35' 5-7/8"3:12 Pitch1' 3/8"2' 3/4"3' 1-1/8"4' 1-1/2"5' 1-7/8"6' 2-1/4"7' 2-5/8"8'3"9' 3-3/8"10' 3-3/4"11' 4-1/8"12' 4-3/8"13' 4-3/4"14' 8-1/8"15' 5-1/2"16' 5-7/8"17' 6-1/4"18' 6-5/8"19' 7"20' 7-3/8"21' 7-3/4"22' 8-1/8"23' 8-1/2"24' 8-7/8"25' 9-1/4"26' 9-1/2"27' 9-7/8"28' 10-1/4"29' 10-5/8"30'11"31' 11-3/8"32' 11-3/4"34' 1/8"35' 1/2"36' 7/8"4:12 Pitch1' 5/8"2' 1-1/4"3' 2"4' 2-5/8"5' 3-1/4"6' 3-7/8"7' 4-1/2"8' 5-1/4"9' 5-7/8"10' 6-1/2"11' 7-1/8"12' 7-3/4"13' 8-1/2"14' 9-1/8"15' 9-3/4"16' 10-3/8"17' 11"18' 11-5/8"20' 3/8"21' 1"22' 1-5/8"23' 2-1/4"24' 3"25' 3-5/8"26' 4-1/4"27' 5"28' 5-5/8"29' 6-1/4"30' 6-7/8"31' 7-1/2"32' 8-1/8"33' 8-3/4"34' 9-3/8"35' 10"36' 10-5/8"5:12 Pitch1'1"2'2"3'3"4'4"5'5"6'6"7'7"8'8"9'9"10'10"11'11"13'0"14'1"15'2"16'3"17'4"18'5"19'6"20'7"21'8"22'9"23'10"24'11"26'0"27'1"28'2"29'3"30'4"31'5"32'6"33'7"34'8"35'9"36'10"37'11"6:12 Pitch1' 1-3/8"2' 2-7/8"3' 4-1/4"4' 5/8"5' 7-1/8"6' 8-1/2"7' 9-7/8"8' 11-3/8"10' 3/4"11' 2-1/8"12' 3-5/8"13' 5"14' 6-3/8"15' 7-7/8"16' 9-1/4"17' 10-5/8"19' 1/8"20' 1-1/2"21' 2-7/8"22' 4-3/8"23' 5-3/4"24' 7-1/8"25' 8-5/8"26' 10"27' 11-3/8"29' 3/4"30' 2-1/4"31' 3-3/4"32' 5-1/8"33' 6-1/2"34' 7-7/8"35' 9-1/436' 10-3/4"38' 1/4"39' 1-5/8"
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 10* Longer lead times may apply. ** Copper Metallic is FEVE FEVE = Flourinated Polymer Paint SAystem. Galvalume® is a registered trademark of BIEC International, Inc..HOW TO ORDER TRIMUN 6 RR TRIM GAUGE COLOR CODE CODE CODE TRIM CODEEXAMPLE: Universal Ridge Cap, 26 gauge, RusticUNIVERSAL RIDGE CAPUN - Girth 24" PAINTSTEP 1:In CentralLink™, start by entering the Item ID. Item ID is made of the TRIM CODE, a GAUGE CODE, and a COLOR CODE. The TRIM CODE can be found with each drawing next to the trim's name. The GAUGE CODE and COLOR CODES are found below.STEP 2:Then type the number of pieces you needalong with the length in feet and inches.pitchCOLOR CODESGAUGE CODE26 629 9GAUGE CODES PANEL TRIMSMP GAUGE GAUGE CODEAlamo 29 AWBlack 29 BKBrilliant 26 29/26 BIBrown 26 29/26 BRBurgundy 26 29/26 BGBurnished Slate 26 29/26 BSCharcoal 26 29/26 CHColony 26 26 CGCopper Metallic** 26 29/26 CMCrimson 26 29/26 CRDesert 26 26 DSForest 29/26 DGFern 26 26 FNGallery 26 29/26 GBGalvalume® 26 29/26 GLGalvanized 29 ZNGray 26 29/26 GAHawaiian 26 26 HBHunter 26 29/26 GRIvory 29 IVLight Stone 26 29/26 LSOcean 29 OBPewter 29 PGPolar 26 26 PWRustic 26 29/26 RRTan 26 29/26 TNTaupe 29/26 TALookupUN6RREnter Item IDPieces10Feet12Inches2Description: 26, Rustic, Universal Ridge Cap CentralLink order screen
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 11ROOF TRIMSUnless otherwise noted all angles are 90° or 45°. See page 10 for gauge and color codes.36"18"UNIVERSAL RIDGE CAPUN - Girth 24" RIDGE CAP - Specify pitch.Additional pallet charge may apply.FORMED RIDGE CAPRLFRC36 - Length 3' Specify pitch up to 4:12. Longer lead times may apply.PAINTpitchPAINTRAKERA - Girth 20.75" RAKE/GABLERAKE PEAK BOXPBOXF Specify pitch.RAKE END CAPREND - Left hand shown.HOUSE RAKEHR - Girth 12.5"105°105°150°HIGH-SIDE EAVEHI - Girth 20.75" EAVE - Specify pitch.SHORT EAVESEA - Girth 9.5" LONG EAVELEA- Girth 9.5" pitchPAINT PAINT PAINTPAINTBOX RAKEBRT - Girth 20.75" BOX RAKE PEAK BOXPBBF Specify pitch.BOX RAKE END CAPBREND - Left hand shown.126342PAINTPAINTPAINT PAINTPAINTPAINTpitchpitch26 ga. only.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 12Unless otherwise noted all angles are 90° or 45°. See page 10 for gauge and color codes.ROOF TRIMSSNOW GUARDSG1 - Girth 5.5" MISC. TRIMSAvailable in 10'2" only.½"hem½" hem1"1"1½"138°55°1"TRANSITION TT - Girth 12.5" TRANSITION TRIMS - Specify pitch.TRANSITIONGTL2 - Girth 14.5" TIE-INTI - Girth 10.375" pitchPAINTPAINTPAINTPAINTCOMMERCIAL VALLEYVA - Girth 20.75" Intended for valley lengths less than 30'.Additional pallet charge will apply.EXTENDED VALLEYEVA- Girth 41.5" Intended for valley lengths greater than 30'.Additional pallet charge will apply.pitchPAINTpitchHIGH SIDE PARAPETHSP - Girth 10.5"ENDWALLEW - Girth 10.25" PAINTSIDEWALLST- Girth 11.75"PAINTFLAT SHEETFS6 - 26 gauge. Girth 41.5625"10 sheets or fewer will be packaged in a roll.Additional pallet charge on orders of 10 or more.PAINTVALLEY - Specify pitch.PAINT
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 13Unless otherwise noted all angles are 90° or 45°. See page 10 for gauge and color codes.WALL TRIMSOUTSIDE CORNEROU - Girth 13.25" INSIDE CORNERIN - Girth 14.5" ZEE TRIMZE - Girth 5.875" COMMERCIAL RAT GUARDRGC - Girth 8.3125" BASE TRIMBA - Girth 6.125" WAINSCOTWA - Girth 7.75"PAINTHEAD TRIMHE - Girth 5.75" FRAMED OPENING TRIMSJAMBJA - Girth 5.75" JAMB HEADERJH - Girth 13" 45°PAINTANGLE TRIMSPAINT PAINTPAINTPAINTPAINTPAINTPAINTINSIDE ANGLEIA2X2 - Girth 5" IA3X3 - Girth 7"IA4X4 - Girth 9"OUTSIDE ANGLESA2X2 - Girth 5" SA3X3 - Girth 7"SA4X4 - Girth 9"PAINT2"3" 4"2"3" 4"PAINT2"3" 4"2"3" 4"
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 14GUTTERS378"338"ROOF PANELINSIDE CLOSUREEAVE TRIM45° ELBOWBUTYL TAPEBUTYL TAPEGUTTERDOWNSPOUTFIELD CUT & BEND OUTLET(SEAL CONNECTION AND FASTENWITH POP RIVETS)IN BOTTOM OF GUTTER#12 X 7/8" LAP(2 PER GUTTER STRAP)GUTTER STRAP(36" O.C.)#12 X 7/8" LAP (12" O.C.)DOWNSPOUT OUTLETDOWNSPOUT STRAPDOWNSPOUT SLEEVE45° ELBOWDOWNSPOUT SLEEVESLEEVE (TYP)SLEEVE (TYP)45° ELBOWSLEEVE (TYP)SOFFIT PANEL
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 15Unless otherwise noted all angles are 90° or 45°. See page 10 for gauge and color codes.GUTTERSHANG-ON 0-4:12 PITCHRLGU - Girth 20.75" HANG-ON 5:12 PITCHRLGU5 - Girth 22.1875" HANG-ON 6:12 PITCHRLGU6 - Girth 22.4375" 4"4"4"¾"1"150°105°½"hem123°pitchpitch6 ½"EAVE 0-4:12 PITCHRLSGU - Girth 24" EAVE 5:12 PITCHRLSGU5- Girth 25.4375" 4"4"4"1"4"150°105°½"hem123°pitchpitch6½"EAVE 6:12 PITCHRLSGU6 - Girth 25.6875" PAINTSCULPTURED GUTTERSBOX GUTTERS - Dimension "A" will change depending on chosen pitch. 4"4"4"¾"1"½"hemroofpitchroofpitch150°105°7 ⁄”PAINT PAINTPAINT150°½"hem4"4"4"1"4"105°roofpitchroofpitch7 ⁄”PAINT PAINTHANG-ONPAINTRLBHG1 1:12 17.625" 4.375"RLBHG2 2:12 18.125" 4.875" RLBHG3 3:12 18.5625" 5.3125"RLBHG4 4:12 19.063" 5.8125"RLBHG5 5:12 19.5" 6.25"RLBHG6 6:12 20" 6.75"PART # PITCH GIRTH DIM. “A”BOX EAVERLBEG1 1:12 20.875" 4.375"RLBEG2 2:12 21.375" 4.875" RLBEG3 3:12 21.813" 5.3125"RLBEG4 4:12 22.313" 5.8125"RLBEG5 5:12 22.75" 6.25"RLBEG6 6:12 23.25" 6.75"PART # PITCH GIRTH DIM. “A”PAINT4"4"4"¾"1"½"hemroofpitchroofpitch150°105°8 ⁄”150°½"hem4"4"4"1"4"105°roofpitchroofpitch8 ⁄”(left or right)(left)DOWNSPOUT- Length 16" DS - straightDK - with kickoutDOWNSPOUTSDOWNSPOUT STRAPDSSDOWNSPOUT OUTLETDSOUTLETSpecify pitch. 1/2" turndowns.3 ½"3 ½"4"4"4"3 ½"DOWNSPOUT ELBOWDSE45DSE90GUTTER STRAPRLGS9631/2"2"41/4"SCULPTURED GUTTER END CAPGEN - Specify pitch and left or right.Left or right as you are on the ground looking at the gutter expanse from the eave.130°±9"1"1¼"DOWNSPOUT CONNECTORDSLVEOUTSIDE CORNER BOXOCB - Specify pitch. INSIDE CORNER BOXICB - Girth 25.6875" PAINTUse with sculptured gutters.PAINTUse with sculptured gutters.(right)3 ½"3 ½"4"4"4"3 ½"PAINT PAINTBOX GUTTER END CAPBGEN - Specify pitch.PAINTDS DK
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 16TYPE PART # LENGTH DIAMETER HEAD COLOR #BAGMETAL/METAL 114(color)MM 1 1/4" #12 5/16" Hex all 250METAL/METAL 2ZMM 2" #12 5/16" Hex galvanized 250METAL/METAL LAP 78(color)LAP 7/8" #14 5/16" Hex all 250ZAC METAL/METAL 114ZACMM 1 1/4" #12 5/16" Hex galvanized 250ZAC METAL/METAL LAP 78ZACLAP 7/8" #14 5/16" Hex galvanized 250Fastener color availability may vary by location, contact your sales consultant for details. Order fasteners in increments of 250 pieces.FASTENERSACCESSORIESDOOR LEAF - Steel door leaf only.3070DOOR - 3 x 7'3070DOORW/LITE - 3' x 7'with window.4070DOOR - 4' x 7'COVERAGE 36"Clear PolycarbonateRLSKYPCC12 - Length 12'.White PolycarbonateRLSKYPCW12 - Length 12'.SKYLIGHTS For best results, use approved sealant (MRS10SKY), Skylight Trim (SK) and washer (118WASHER). Skylights should be predrilled.Skylight Washer - White.118WASHER - ⁄" outside diameter, ¼" inside diameter100 per bag.Skylight Sealant - Clear.MRS10SKY - 10.3 oz. tubeApproved for skylight use.DOORS & FRAMING PACKAGE - Longer lead times may apply.FRAMING PACKAGE - White.4X3070JAMB - 4.25" x 30704X4070JAMB - 4.25" x 40706X3070JAMB - 6.25" x 30706X4070JAMB - 6.25" x 40708X3070JAMB - 8.25" x 30708X4070JAMB - 8.25" x 40708X6070JAMB - 8.25" x 6070 Package includes: Jambs, headers, threshold, door lever with keyed lock, hinges, and weather strip kit. Frames are non-reversable. Swing-out only.Skylight TrimSK - Girth 6".PAINTSkylight Ridge Cap - UniversalRCPCC10 - Clear PolycarbonateRCPCW10 - White PolycarbonateLength 10'6"'. Width 25". 6 1⁄8"¾"¾"3 ½"2 1⁄8"
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 17BUTYL TAPEInstall between fastener and exposed edge.Rolls per box may vary by location and vendor. Check with your sales consultant for details.BTL 45' 3/4" 3/32" 24BTR 40' 7/8" 3/16" 10BT3/8 45' 3/8" 3/32" 40Recommended for R-Loc.TOUCH UP PAINTTP(color) - SMP, 0.6 oz. bottle w/brush.12PURSP - Purlin paint. 12oz. spray.PART # LENGTH WIDTH THICKNESS ROLLS PER BOXSEALANTPART # SIZE COLORGEO(color) 10.3 oz. tube clear, gray, whiteMRS10(color) 10.3 oz. tube call for colorsMRS10CLEAR 10.3 oz. tube clearSquare - Max temperature 250°.MPF - Pipe size .25" to 5.75" MPF2 - Pipe size .875" to 4"MPF4 - Pipe size 2.75" to 7"MPF6 - Pipe size 4.75" to 10"MPF8 - Pipe size 6.75" to 13.5"MASTER PIPE FLASHING - Install in a diamond shape and not parallel to the rib.Silicone - Orange, high temp max 500°.4SMPF - Pipe size 2.75" to 7"6SMPF - Pipe size 4.75" to 10"8SMPF - Pipe size 6.75" to 13.5"Square with zipper - Max temperature 250°.MPF1ZIP - Pipe size .5" - 4"MPF2ZIP - Pipe size 4" - 9.25"ACCESSORIESOUTSIDE CLOSURERLCLOUT - No Glue. RLCLOUTGLUE - With Glue. CLOSURESLength - 3'. 100 per box.INSIDE CLOSURERLCLIN - No Glue. RLCLINGLUE - With Glue. Length - 3'. 100 per box.CLOSURE VENTRLCLVLength - 3'. 25 rolls per box.Closure is 1 3/8" tall and may require longer screws for installation. Item may vary from sample shown. UNIVERSAL POLYFOAMPOLYG - With Glue. 10-rolls per box.Length 25'. Width 1 1/2". Thickness 1 1/2". GRAYFLEXGRAYFLEX115 - 24-rolls per box.Length 13'. Width 1". Thickness 1 1/2". For use with hips and valleys. FLEXOVENTFLEXOVENT - (2) 10' rolls per box.Length 10'. Width 3". Thickness 1 1/2".
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 18INTERIOR HALLWAYSELF-STORAGEOUTSIDE VIEWINSIDE VIEWTOP TRACK (TTRACK2)BUILDINGFRAMING16"8' 8" (TYP)WALL LINER (WL2)GIRT ZEE(GZ2)FLUSH BASECHANNEL(FBC2)TOP TRACK (TTRACK2)FLUSHDOORHEADER (FDH2)FLUSHDOORHEADER (FDH2)FLUSHOUTSIDECORNER (FOU2)FLUSH DOOR JAMB(FDJ2)FLUSHMULLION (FM2)BUILDINGFRAMINGGIRT ZEE(GZ2)FLUSH BASECHANNEL(FBC2)TOP TRACK (TTRACK2)TOP TRACK (TTRACK2)FLUSH MULLIONBACKING PLATE (FMBP2)FLUSH JAMBBACKER PLATE (FJB82)FLUSH BASECHANNEL(FBC2)8' 4"(TYP)
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 19Unless otherwise noted, Pier and Header trims are 22 gauge, and all angles are 90°. Call for available colors and lead times.INTERIOR HALLWAYFLUSH MULLIONFM2 - Girth 24" FLUSH MULLION BACKING PLATEFMBP2 - Girth 24" FLUSH DOOR JAMBFDJ2 - Girth 13" 2"1"8"2"2" 2"1’ 4 ⁄"1 ⁄" 1 ⁄"2" 2"1’ 4"2" 2"2"1’ 4"2"1"FLUSH DOOR HEADERFDH2 - Girth 21"FLUSH INSIDE CORNERFIN2 - Girth 7" 3"½" hems3"4"1" hems4"FLUSH OUTSIDE CORNERFOU2- Girth 10"SELF-STORAGEWALL LINERFWL2 - Girth 16" 1’1"1" 1"1 ⁄"1"3 ⁄"FLUSH BASE CHANNELFBC2 - Girth 6"PAINTPAINT PAINT PAINTPAINTPAINTPAINT PAINTFLUSH JAMB BACKER PLATE 8"FJB82 - Girth 12" 2"8"2"2"10"2"FLUSH JAMB BACKER PLATE 10"FJB102 - Girth 14" FLUSH JAMB BACKER PLATE 14"FJB142 - Girth 18" CHECKERED OUTSIDE CORNER CKOUS8AL - Girth 8" CHECKERED WAINSCOT PANEL CKWP8AL - Girth 48" HAT CHANNEL TRIM BURGLAR BAR HATT2GW - Girth 4.8750" CHECKERED INSIDE CORNERCKINS8AL - Girth 8" CHECKERED BASE PLATECKBP8AL - Girth 12" 2"14"2"TOP TRACKFTTRACK2 - Girth 8" 3 7⁄8"2 1⁄8"2"2 ½"1"1"2 ½"GIRT ZEEFGZ16Z- Girth 6"Galvanized 16 ga. only. PAINT PAINT PAINT PAINTPAINTTYPE PART # LENGTH DIAMETER HEAD COLOR #BAGMETAL/METAL (no washer) 58(color)MMNW* 5/8" #10 5/16" Hex ask for details 250METAL/METAL (no washer) 1ZMMNW 1" #12 5/16" Hex galvanized 250MASONRY ANCHOR 11FASTENER 1 1/4" 1/4" Mushroom galvanized 100FASTENERS*Longer lead times may apply.12"4’4”4”4”4”4’4’Glossy White, 26 ga. only. Aluminum 18 ga. only. Aluminum 18 ga. only. Aluminum 18 ga. only. Aluminum 18 ga. only.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 20Members can be manufactured to the nearest 1/8" in length from 6'0" to 45'0". For lengths under 6'0" or over 45'0", call your sales consultant.SECONDARY FRAMINGSingle Slope Up Single Slope Down Double Slope Up Double Slope Down* Specify pitch and slope when ordering. For low pitch (up to 4:12) add a "L" to the end of the code. For high pitch (5:12 and above) add a "H" to the end of the code.Central States has met the requirements to earn the accreditation for Cold-Formed Steel Structural and non-Structural Components Not Requiring Welding For more information, go to www.iasonline.org.25218343121347241453413437878ANGLE CHANNEL CEE LGSI ZEE ZEEEAVE STRUTSGIRT CLIPGIRTCLIP - 10 gauge.GIRTCLIPZ - 10 gauge.MINI CLIPMINICLIP- 16 gauge.PURLIN CLIPSBASE CLIPBASECLIP- 14 gauge.Galvanized.HAT CHANNELHS116R - Specify length, 20 gauge, Red Oxide.HS116Z - Specify length, 16 gauge, galvanized.HAT20Z - Specify length, 20 gauge, galvanized.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 21SECONDARY FRAMING ITEM CODE ITEM CODETYPE A x B GAUGE RED OXIDE GALVANIZEDAngle 2.5 x 2.5 14 B2514RAngle 3 x 3 16 B316R B316ZAngle 3 x 3 14 B314R B314ZAngle 4 x 2 16 B4216R B4216ZAngle 4 x 2 14 B4214R B4214ZAngle 4 x 3 16 B4316RTYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDChannel 4.25 x 2.35 x 2.35 16 U4216R U4216ZChannel 4.25 x 2.85 x 2.85 16 U42516R U42516ZChannel 4.25 x 2.85 x 2.85 14 U42514R U42514ZChannel 4.25 x 2.85 x 2.85 12 U42512R U42512ZChannel 6.25 x 2.85 x 2.85 16 U62516R U62516ZChannel 6.25 x 2.85 x 2.85 14 U62514R U62514ZChannel 8.25 x 2.85 x 2.85 16 U82516R U82516ZChannel 8.25 x 2.85 x 2.85 14 U82514R U82514ZChannel 8.25 x 2.85 x 2.85 12 U82512R U82512ZTYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDEave Strut 6 x 4 x 3 16 E64316R* E64316Z*Eave Strut 6 x 4 x 3 14 E64314R* E64314Z*Eave Strut 6 x 4 x 3 12 E64312R* E64312Z*Eave Strut 8 x 4 x 3 14 E84314R* E84314Z*Eave Strut 8 x 4 x 3 12 E84312R* E84312Z*Eave Strut 8 x 5 x 3 14 E85314R* E85314Z*Eave Strut 8 x 5 x 3 12 E85312R* E85312Z*Eave Strut 8 x 5 x 5 14 E85514R*Eave Strut 10 x 5 x 3 14 E105314R*TYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDCEE 4 x 2 x 2 16 C4216R C4216ZCEE 4 x 2.5 x 2.5 16 C42516R C42516ZCEE 4 x 2.5 x 2.5 14 C42514R C42514ZCEE 4 x 2.5 x 2.5 12 C42512R C42512ZCEE 4 x 3.5 x 3.5 16 C43516R C43516ZCEE 4 x 3.5 x 3.5 14 C43514R C43514ZCEE 6 x 2.5 x 2.5 16 C62516R C62516ZCEE 6 x 2.5 x 2.5 14 C62514R C62514ZCEE 8 x 2.5 x 2.5 16 C82516R C82516ZCEE 8 x 2.5 x 2.5 14 C82514R C82514ZCEE 8 x 2.5 x 2.5 12 C82512R C82512ZCEE 8 x 3.5 x 3.5 16 C83516R C83516ZCEE 8 x 3.5 x 3.5 14 C83514R C83514ZCEE 8 x 3.5 x 3.5 12 C83512R C83512ZCEE 9 x 3 x 3 14 C9314R C9314ZCEE 9 x 3 x 3 12 C9312R C9312ZCEE 10 x 2.5 x 2.5 16 C102516R C102516ZCEE 10 x 2.5 x 2.5 14 C102514R C102514ZCEE 10 x 2.5 x 2.5 12 C102512R C102512ZCEE 10 x 3.5 x 3.5 14 C103514R C103514ZCEE 10 x 3.5 x 3.5 12 C103512R C103512ZCEE 12 x 2.5 x 2.5 14 C122514R C122514ZCEE 12 x 2.5 x 2.5 12 C122512R C122512ZCEE 12 x 3.5 x 3.5 14 C123514R C123514ZCEE 12 x 3.5 x 3.5 12 C123512R C123512ZCEE 12 x 4 x 4 16 C12416R C12416Z ITEM CODE ITEM CODETYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDLGSI ZEE 4 x 2½ x 2⁄ 16 Z42516R Z42516ZLGSI ZEE 6 x 2⁄ x 2⁄ 16 Z62516R Z62516ZLGSI ZEE 6 x 2⁄ x 2⁄ 14 Z62514R Z62514ZLGSI ZEE 8 x 2⁄ x 2⁄ 16 Z82516R Z82516ZLGSI ZEE 8 x 2⁄ x 2⁄ 14 Z82514R Z82514ZLGSI ZEE 8 x 2⁄ x 2⁄ 12 Z82512R Z82512ZLGSI ZEE 8 x 3⁄ x 3⁄ 16 Z83516R Z83516ZLGSI ZEE 8 x 3⁄ x 3⁄ 14 Z83514R Z83514ZLGSI ZEE 8 x 3⁄ x 3⁄ 12 Z83512R Z83512ZLGSI ZEE 10 x 2⁄ x 2⁄ 16 Z102516R Z102516ZLGSI ZEE 10 x 2⁄ x 2⁄ 14 Z102514R Z102514ZLGSI ZEE 10 x 2⁄ x 2⁄ 12 Z102512R Z102512ZLGSI ZEE 10 x 2⁄ x 2⁄ 14 Z10314R Z10314ZLGSI ZEE 10 x 2⁄ x 2⁄ 12 Z10312RLGSI ZEE 12 x 2⁄ x 2⁄ 14 Z122514R Z122514ZLGSI ZEE 12 x 2⁄ x 2⁄ 12 Z122512R Z122512ZLGSI ZEE 12 x 3⁄ x 3⁄ 14 Z123514R Z123514ZLGSI ZEE 12 x 3⁄ x 3⁄ 12 Z123512R Z123512ZLGSI ZEE 12 x 3⁄ x 3⁄ 16 Z12416R Z12416ZTYPE WEB x A x B GAUGE RED OXIDE GALVANIZEDZEE 4 x 2 x 2 16 Z4216R Z4216ZZEE 4 x 2.5 x 2.5 16 Z42516R Z42516ZZEE 4 x 2.5 x 2.5 14 Z42514R Z42514ZZEE 4 x 2.5 x 2.5 12 Z42512R Z42512ZZEE 4 x 3.5 x 3.5 16 Z43516R Z43516ZZEE 4 x 3.5 x 3.5 14 Z43514R Z43514ZZEE 6 x 2.5 x 2.5 16 Z62516R Z62516ZZEE 6 x 2.5 x 2.5 14 Z62514R Z62514ZZEE 8 x 2.5 x 2.5 16 Z82516R Z82516ZZEE 8 x 2.5 x 2.5 14 Z82514R Z82514ZZEE 8 x 2.5 x 2.5 12 Z82512R Z82512ZZEE 8 x 3.5 x 3.5 16 Z83516R Z83516ZZEE 8 x 3.5 x 3.5 14 Z83514R Z83514ZZEE 8 x 3.5 x 3.5 12 Z83512R Z83512ZZEE 9 x 3 x 3 14 Z9314R Z9314ZZEE 9 x 3 x 3 12 Z9312R Z9312ZZEE 10 x 2.5 x 2.5 16 Z102516R Z102516ZZEE 10 x 2.5 x 2.5 14 Z102514R Z102514ZZEE 10 x 2.5 x 2.5 12 Z102512R Z102512ZZEE 10 x 3.5 x 3.5 14 Z103514R Z103514ZZEE 10 x 3.5 x 3.5 12 Z103512R Z103512ZZEE 12 x 2.5 x 2.5 14 Z122514R Z122514ZZEE 12 x 2.5 x 2.5 12 Z122512R Z122512ZZEE 12 x 3.5 x 3.5 14 Z123514R Z123514ZZEE 12 x 3.5 x 3.5 12 Z123512R Z123512ZZEE 12 x 4 x 4 16 Z12416R Z12416Z *For low pitch (up to 4:12) add a "L" to the end of the code. For high pitch (5:12 and above) add a "H" to the end of the code.
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 22Punch capabilities vary by location. Call for pricing and availability on special punching.Punches cannot be made on secondary framing members shorter than 3".Holes are punched to accommodate 1/2" diameter bolts.STANDARD PUNCH PATTERNSFLANGE PATTERNS - Punches can be placed on either or both ends.EAVE STRUT FOR 4" LEGES4EAVE STRUT FOR 5" LEGES5 EAVE STRUT FOR 5" LEGES134PATTERN D - OPTIONAL FLANGEPPDUse with web pattern A.PATTERN E - OPTIONAL FLANGEPPEUse with web pattern B.PATTERN F - OPTIONAL FLANGEPPFUse with web pattern C.Standard hole sizes:LOCATION⁄” ROUND ⁄” ROUND ⁄” x ¾” SLOTLowell X X XJasper X XCedar Hill X XSeguin X XClaysburg X X
CENTRAL STATES MANUFACTURING, INC.Effective 05/2023 • Information subject to change 23END PUNCHPPEPPATTERN H STANDARD WEB ENDPPHSIMPLE SPAN PUNCHPPSS Minimum part length 5' total, 2'6" one end.SHORT LAP PUNCHPPSLMinimum part length 5'6" total, 2'8" one end.LONG LAP PUNCHPPLLMinimum part length 7' total, 3'6" one end.WEB PATTERNS - Punches can be placed on either or both ends.STANDARD PUNCH PATTERNSPATTERN A - STANDARD WEB - 9' Minimum length if punched on both ends; 4'6" if punched on one end.PPAPATTERN B - STANDARD WEB - 12'5" Minimum length if punched on both ends; 6'2.5" if punched on one end.PPBPATTERN C - STANDARD WEB - 7' Minimum length if punched on both ends; 3'6" if punched on one end.PPC
Clear acrylic coatingGalvalume®‡ PRIMEHunter PRIMEBrown PRIMEBurnished Slate PRIMETan PRIMEColony PRIMECrimson PRIMERustic PRIMEBurgundy PRIMEGallery PRIME Hawaiian PRIME Light Stone PRIMEPolar PRIMEDesert PRIMEBrilliant PRIMECharcoal PRIMEGray PRIMECommercial Color Selection ToolFern PRIMEM-Loc™R-Loc™Choose CentralGuard for the best protection and a lifetime warranty.centralstatesco.comCHRT_COML_East_240401E† Color variation between orders is normal and not cause for rejection. ‡ Weathering and appearance variation, including color, sheen, and spangle, is common in non-painted materials and is not a cause for rejection. For consistent appearance, choose a paint-nished product. Colors on this chart are close representations of actual metal color, limited by printing and viewing conditions. Color matching optimized for outdoor viewing. Copper Metallic*† PRIMECopper Metallic† PRIMEFEVEFluorinated Polymer Paint System
R-Loc™ M-Loc™ Choose CentralGuard®for the best protection anda lifetime warranty.Copyright © 2024, Central States Manufacturing, Inc., All Rights Reserved.CentralGuard® is a trademark of Central States® Manufacturing, Inc.Galvalume® is a registered trademark of BIEC International, Inc.CentralGuard is our specic combination of everything that goes into making the highest-quality metal panels. Available on our Prime panels, the CentralGuard name guarantees that you have the best protection and a lifetime paint warranty.Choose CentralGuard for the perfect balance of fade protection, rust blocking, and dent resistance. Get started quickly with our preloaded photos, or upload your own photo. When you nd the perfect combination of panel and color, you’ll receive a summary of your project and have the option to connect with a local expertin your area to help you with your purchase and installation. visualizer.centralstatesmfg.comExplore our visualizer.PRIME ULTRACentralGuard CentralGuardFADE PROTECTIONPaint WarrantyLIFETIME LIFETIMEPaint ThicknessTHICKER 1.0 mil THICKER 1.0 milFade Warranty30-YEAR 30-YEARFade ProtectionP PRUST BLOCKINGAdvanced Rust BlockingP PPerforation Warranty50-YEAR 50-YEARSubstrate Thickness1.60 mil 1.60 milDENT RESISTANCEAdvanced Dent ResistancePP PPSteel ThicknessTHICK THICKESTSteel Gauge26 ga. 24 ga. Color Selection SEE COLOR CHARTGALVALUME® AND POLARINSTALLATIONPurlin Bearing LegP POUR BEST SELLER!ULTIMATE DENT RESISTENCE
HunterRusticGrayCharcoalLight StoneTanBrownPolarPanel-Loc Plus™ - 26 gaugeR-Loc™ - 26 gauge M-Loc™ - 26 gaugeThrifty Color Selection ToolPanel-Loc Plus™M-Loc™R-Loc™50LIMITEDPAINTWARRANTYYEARCHRT_THRL_240219EColors on this chart are close representations of actual metal color, limited by printing and viewing conditions. Color matching optimized for outdoor viewing.Copyright © 2024, Central States Manufacturing, Inc., All Rights Reserved. centralstatesco.com