Return to flip book view

INSTALLATION INSTRUCTIONS WINDSOR THIS SHOWER IS PRE CUT TO FIT A 56 1 2 TO 59 WIDE OPENING DANGER IF THIS SHOWER IS INSTALLED IN AN OPENING OVER 59 THIS COULD RESULT IN SERIOUS INJURY 24 10 17 Rev 1 0

CONFIGURATIONS THIS CONFIGURATION IS ILLUSTRATED IN THIS MANUAL NOTE THE WINDSOR ENCLOSURE IS REVERSIBLE FOR LEFT OR RIGHT SIDE SHOWER HEAD CONFIGURATIONS THIS MANUAL WILL SHOW THE LEFT SIDE SHOWER HEAD INSTALLATION FOR RIGHT SIDE SHOWER HEAD INSTALLATION SIMPLY BEGIN ON THE OPPOSITE WALL AND REVERSE THE ORIENTATION OF THE PARTS AS NECESSARY 1

Assembly Drawing 1 11 12 5 5 12 11 1 14 14 16 13 3 14 14 13 15 15 15 15 3 10 10 3 6 8 9 4 3 2 8 7 6 1 3 3 2 PACKING LIST PART DESCRIPTION Q TY PART DESCRIPTION Q TY 1 Wall Plugs A 10pcs 10 Handle 2pcs 2 Aluminium Water Guard A 2pcs 11 Wall Brackets 2pcs 3 End Block 6pcs 12 Screws ST5x2 8pcs 4 Screws ST4x1 3 8 2pcs 13 Door Panels 2pcs 5 Tracks 2pcs 14 Rollers 4pcs 6 Gasket A 2pcs 15 Anti Lift Pins 4pcs 7 Aluminium Water Guard B 1pc 16 Gasket C 1pc 8 Gasket B 2pcs 17 Installer Kit 1set 9 Bottom Guide 1pc 2

Inspect the product immediately upon receipt for transit damage missing packs parts or manufacturing defects Handle the product with care Do not set on hard surface and protect all edges and corners from impact Tempered glass is up to 4 times stronger than annealed glass but edges and corners can be very fragile Si l ic on e Notes Read these instructions carefully before start of installation Special care should be taken when drilling walls to avoid hidden pipes or electrical cables This product is heavy and may require two people to install 2 PHILIPS INSTALLATION KIT 17 1 4 Installation Foam Blocks 3 Wrenches Masonry Bits Sealant Finishing Tool Allen Wrenches Painters Tape Installer Templates

STEP 1 FINDING CENTERLINE OF CURB TO FIND CENTERLINE PLACE TEMPLATE A ON CURB AND MATCH NUMBERS 3 3 2 2 1 1 1 1 2 2 3 3 4 9 12 15 6 3 3 6 15 12 9 5 4 4 4 CENTERLINE WALL CURB 5 9 12 15 6 3 6 15 12 9 9 12 15 9 12 15 6 6 3 3 3 3 6 6 CURB 15 12 9 15 12 9 3 ON FRONT AND BACK EDGES OF CURB AND MARK CENTERLINE 4

STEP 2 MARK AND DRILL HOLES FOR WALL BRACKETS ENSURE CENTERLINE ON TEMPLATE B LINES UP A WITH CENTERLINE ON CURB DIAGRAM A USE LEVEL TO MAKE SURE TEMPLATE IS PLUMB AND MARK HOLES AND DRILL DIAGRAM B AND C REPEAT STEP FOR OPPOSITE WALL B B B NOTE ENSURE YOU MARK CORRECT HEIGHT FOR YOUR UNIT EITHER 66 OR 78 1 4 C A 5 A

STEP 3 INSERT BUMPER BLOCKS INTO WALL BRACKETS A FOR CONFIGURATIONS WITH SHOWER HEAD TO THE LEFT INSERT BUMPER BLOCKS INTO WALL BRACKETS AS SHOWN 1 4 BUMPER 5 8 BUMPER 5 8 BUMPER 1 4 BUMPER 1 4 5 8 5 8 1 4 B FOR CONFIGURATIONS WITH SHOWER HEAD TO THE RIGHT INSERT BUMPER BLOCKS INTO WALL BRACKETS AS SHOWN 5 8 BUMPER 1 4 BUMPER 5 8 1 4 1 4 BUMPER 5 8 BUMPER 1 4 5 8 6

STEP 4 INSTALL WALL BRACKETS ON LEFT AND RIGHT WALL AS SHOWN 10 1 9 9 10 Screw ST5x2 7 1 Screw ST5x2

STEP 5 INSTALLING BOTTOM GUIDE LINE UP CENTERLINE ON TEMPLATE C WITH CENTERLINE ON CURB PEEL OFF TABS AND STICK CENTERLINE TEMPLATE ONTO CURB DIAGRAM A B AND C A OVERHEAD VIEW WALL EQUAL CENTERLINE B CURB CENTERLINE LEFT SIDE EQUAL DISTANCES OVERHEAD VIEW MARK HOLES FOR BOTTOM GUIDE AND EQUAL DRILL HOLES DIAGRAM D AND E CENTERLINE C LASTLY INSTALL BOTTOM GUIDE DIAGRAM F RIGHT SIDE 4 9 CENTERLINE Screw ST4x1 3 8 1 4 1 D E F 8

STEP 6A INSTALL SEALS ON EXTERIOR DOOR INSTALL BOTTOM PLASTIC WATER DIVERTER AND V SEAL ON EXTERIOR DOOR DIAGRAM A AND B 13 6 A PLACE THE PANEL ON CARBOARD BOX TO INSTALL THE SEALS A 13 INTERIOR SHOWER SIDE 8 B 13 8 B 9

STEP 6B INSTALL SEALS ON INTERIOR DOOR INSTALL BOTTOM PLASTIC WATER DIVERTER AND V SEAL ON INTERIOR DOOR DIAGRAM A AND B 13 6 A PLACE THE PANEL ON CARBOARD BOX TO INSTALL THE SEALS 13 A INTERIOR SHOWER SIDE 8 13 B 8 A 10

STEP 7 INSTALLING ROLLERS ON EXTERIOR DOOR 13 13 14 NOTE DO NOT INSTALL ROLLER CAP AT THIS POINT Eccentric nut for roller adjustment Raises and lowers the roller Minimum spacing should be oriented towards the middle as shown Adjustments can be made after the door installation STEP 8 VERIFY ROLLERS AND PLASTIC WATER DIVERTER ARE INSTALLED PROPERLY AND LEAN DOOR AGAINST WALL OUTSIDE SHOWER 13 13 14 INTERIOR SIDE EXTERIOR SIDE WALL INTERIOR SIDE EXTERIOR SIDE 8 11 SIDE VIEW OUTSIDE SHOWER

STEP 9 INSTALLING ROLLERS ON INTERIOR DOOR 13 13 14 NOTE DO NOT INSTALL ROLLER CAP AT THIS POINT Eccentric nut for roller adjustment Raises and lowers the roller Minimum spacing should be oriented towards the middle as shown Adjustments can be made after the door installation STEP 10 VERIFY ROLLERS AND PLASTIC WATER DIVERTER ARE INSTALLED PROPERLY AND LEAN DOOR AGAINST WALL OUTSIDE SHOWER 13 13 14 INTERIOR SIDE EXTERIOR SIDE WALL INTERIOR SIDE EXTERIOR SIDE 6 SIDE VIEW OUTSIDE SHOWER 12

STEP 11 INSTALLING INTERIOR TRACK PLACE INTERIOR TRACK INTO WALL BRACKET AS SHOWN DIAGRAM A VERIFY TRACK IS CENTERED BY ENSURING MEASUREMENTS ARE EQUAL AND WARNING LINES ARE NOT EXPOSED DIAGRAM B C AND D ONCE IN PROPER POSITION INSTALL COVERS AND TIGHTEN SET SCREWS DIAGRAM E EQUAL DISTANCES 5 11 LEFT SIDE A WRONG C B WARNING LINES RIGHT SIDE WARNING LINES CORRECT 5 11 5 11 D E E STEP 12 HANG INTERIOR DOOR 13 14 8 9 5 A 13 B

STEP 13 INSTALLING EXTERIOR DOOR PLACE STYROFOAM BLOCKS ONTO CURB DIAGRAM A USE THE STYROFOAM BLOCKS FROM PACKAGING LABELED INSTALLATION TOOL SET EXTERIOR DOOR ON TOP OF STYROFOAM BLOCKS AND SLIDE GLASS INTO GLASS POCKET ON WALL BRACKET DIAGRAM B AND C A B C NOTE PLACE BLOCKS HORIZONTALLY NOT VERTICALLY 14

STEP 14 INSTALLING EXTERIOR TRACK PLACE EXTERIOR TRACK INTO WALL BRACKET AS SHOWN DIAGRAM A VERIFY TRACK IS CENTERED BY ENSURING MEASUREMENTS ARE EQUAL AND WARNING LINES ARE NOT EXPOSED DIAGRAM B C AND D ONCE IN PROPER POSITION INSTALL COVERS AND TIGHTEN SET SCREWS DIAGRAM E EQUAL DISTANCES 5 11 LEFT SIDE RIGHT SIDE B C A WARNING LINES WRONG WARNING LINES CORRECT 5 11 5 11 D E STEP 15 HANG EXTERIOR DOOR IF DOOR ALIGNS PROPERLY WITH SIDE WALLS GO TO STEP 15 IF NOT REFER TO STEP 15A 14 5 SIDE VIEW A 15 INTERIOR SHOWER SIDE B E

STEP 16 ALIGNING DOORS TO WALL ROTATE ROLLERS TO CLOSE GAPS USING PROVIDED ALLEN WRENCH AS SHOWN DIAGRAM A ONCE ALIGNED TIGHTEN ROLLER SCREW AND INSTALL ROLLER CAP DIAGRAM B AND C A B EXTERIOR VIEW 13 14 5 5 14 B C NOTE LOOSEN SCREW 1 2 NOTE HOLD ALLEN WRENCH INTERIOR VIEW TURNS TO RELEASE PRESSURE IN PLACE WHEN TIGHTENING A 14 SCREW 16

STEP 17 INSTALL ANTI LIFT PINS 14 5 A 15 INSTALL ANTI LIFT PINS BELOW TRACK DIAGRAM A AND B ADJUST PINS BY ROTATING BUSHING DIAGRAM C ONCE IN CORRECT LOCATION HOLD BUSHING IN PLACE WITH WRENCH AND TIGHTEN NUT DIAGRAM D INSTALL CAP DIAGRAM E REPEAT STEP FOR OTHER THREE PINS B SIDE VIEW 1 16 1 8 14 5 C EXTERIOR VIEW 15 1 16 1 8 14 5 D 15 EXTERIOR VIEW 14 5 E 15 17

STEP 18 FIT BOTTOM ALUMINUM WATER GUARD MEASURE OPENING BETWEEN BOTH WALLS DIAGRAM A NEXT CUT BOTTOM WATER GUARD BASED OFF MEASUREMENT B OBTAIN MEASUREMENT B BY TAKING YOUR MEASUREMENT A AND SUBTRACT 1 DIAGRAM B PLACE BOTTOM WATER GUARD AND CORNER BLOCKS ON CURB DIAGRAM C PLACE WATER GUARD AGAINST GUIDE DIAGRAM D ENSURE MEASUREMENT AT BOTH POINTS ARE THE SAME DIAGRAM E MARK LOCATION OF BOTTOM WATER GUARD WITH A PENCIL DIAGRAM F 7 3 ME AS UR 7 EM EN TB A 1 B MEASUREMENT A A 9 B 13 OVERHEAD VIEW 13 13 9 C 13 13 9 EQUAL DISTANCES D E F 18

STEP 19 INSTALL ALUMINUM WATER GUARD SET REMOVE ONLY ONE CORNER BLOCK PEEL OFF BACK OF STICKY TAB AND STICK ON CURB DIAGRAM A REMOVE BOTTOM WATER GUARD AND OTHER CORNER BLOCK PEEL OFF BACK OF STICKY TABS AND REINSTALL USING PENCIL MARKS AS A GUIDE DIAGRAM B INSTALL LOWER BLOCK ON VERTICAL WALL INSERT SIDE WALL WATER GUARD INTO BOTTOM BLOCK DO NOT REMOVE STICKY TAB BACKING AT THIS TIME DIAGRAM C PLUMB AND MARK TOP WITH PENCIL DIAGRAM D NOW REMOVE STICKY TAB BACKING AND INSTALL WATER GUARD AND TOP BLOCK DIAGRAM E REPEAT DIAGRAMS C D AND E FOR OPPOSITE WALL A B 3 3 3 2 3 7 2 13 13 3 3 2 C 19 3 2 D E

STEP 20 INSTALL F SEAL A 13 16 A 16 13 INTERIOR INTERIOR SHOWER SIDE EXTERIOR STEP 21 INSTALL HANDLES PLASTIC BUSHING A PLASTIC INTERIOR 10 WASHER 13 B PLASTIC BUSHING PLASTIC WASHER EXTERIOR 10 13 1 4 5 8 KNOB KNOB 5 8 1 4 TUBE PLASTIC BUSHING PLASTIC WASHER 5 8 1 4 PLASTIC BUSHING PLASTIC WASHER TUBE SIDE VIEW INTERIOR EXTERIOR 1 4 5 8 20

STEP 22 APPLYING SILICONE A WIPE DOWN AREAS SHOWN WITH CLEAN CLOTH AND DENATURED OR ISOPROPYL ALCOHOL INTERIOR AND EXTERIOR WIPE ALL SURFACES WITH A CLEAN CLOTH TO ENSURE AREAS TO BE SILICONED ARE FREE OF DEBRIS B TAPE OFF AREAS SHOWN WITH PAINTERS TAPE INTERIOR AND EXTERIOR 1 16 1 8 ON METAL SIDE PAINTERS TAPE 1 16 1 8 ON TILE SIDE 21

C CUT OFF TIP OF CAULKING TUBE AT AN ANGLE 45 1 4 D APPLY CAULKING AS SHOWN ENSURE CAULKING IS ADDED TO AREAS REPRESENTED BY THE DOTTED LINE 22

E TOOL WITH PROVIDED SEALING FINISHING TOOL INTERIOR AND EXTERIOR USE PROVIDED SEALANT FINISHING TOOL TO SMOOTH OUT AND REMOVE EXCESS SILICONE F REMOVE TAPE INTERIOR AND EXTERIOR 23

G LET CAULKING CURE FOR 48 HOURS BEFORE USE 48 HOURS 24