Return to flip book view

INSTALLATION INSTRUCTIONS MONTAGE THIS SHOWER IS PRE CUT TO FIT 56 3 4 TO 59 WIDE OPENING DANGER IF THIS SHOWER IS INSTALLED IN AN OPENING OVER 59 THIS COULD RESULT IN SERIOUS INJURY 24 07 18 Rev 1 0

CONFIGURATIONS THIS CONFIGURATION IS ILLUSTRATED IN THIS MANUAL NOTE THE MONTAGE ENCLOSURE IS REVERSIBLE FOR LEFT OR RIGHT HAND INSTALLATION THIS MANUAL WILL SHOW THE RIGHT HAND INSTALLATION FOR LEFT HAND INSTALLATION SIMPLY BEGIN ON THE OPPOSITE WALL AND REVERSE THE ORIENTATION OF THE PARTS AS NECESSARY 1

Assembly Drawing 12 13 3 10A 15 10B 11 14 15 16 14 12 10B 10A 15 17 18 3 15 9 7 8 4 19 1 19 2 3 5 6 7 7 PACKING LIST PART DESCRIPTION Q TY PART DESCRIPTION Q TY 1 Aluminium Bottom Channel 1pc 11 Wall Bracket Screws 2pcs 2 Bottom Guide L R x 1 for each 1set 12 Countersunk Screw ST5x2 2pcs 3 Wall Plugs A 6pcs 13 Track 1pc 4 Countersunk Screw ST4x1 3 16 2pcs 14 Fixed Panel Holders 2pcs 5 Aluminium Water Guard 2pcs 15 Rollers 4pcs 6 Gasket A 1pc 16 Fixed Panel 1pc 7 End Block 3pcs 17 Gasket B 1pc 8 Handle 1pc 18 Door Panel 1pc 9 Gasket C 1pc 19 1 4 Cushions 2pcs 10A Wall Brackets A 2pcs 20 Installation Kit 1set 10B Wall Brackets B 2pcs 2

Inspect the product immediately upon receipt for transit damage missing parts or manufacturing defects Handle the product with care Do not set on hard surface and protect all edges and corners from impact Tempered glass is up to 4 times stronger than annealed glass but edges and corners can be very fragile Si lic on e Notes Read these instructions carefully before start of installation Special care should be taken when drilling walls to avoid hidden pipes or electrical cables Note This product is heavy and may require two people to install 2 PHILIPS INSTALLATION KIT 20 1 4 1 32 1 8 Cushions 3 Masonry Bits Sealant Finishing Tool Allen Wrenches Painters Tape Installer Templates

STEP 1 FINDING CENTERLINE OF CURB TO FIND CENTERLINE PLACE TEMPLATE A ON CURB AND MATCH NUMBERS 3 3 2 2 1 1 1 1 2 2 3 3 4 9 12 15 6 3 3 6 15 12 9 5 4 4 4 CENTERLINE WALL CURB 5 9 12 15 6 3 6 15 12 9 9 12 15 9 12 15 6 6 3 3 3 3 6 6 CURB 15 12 9 15 12 9 3 ON FRONT AND BACK EDGES OF CURB AND MARK CENTERLINE 4

STEP 2 MARK AND DRILL HOLES FOR WALL BRACKETS F ENSURE CENTERLINE ON TEMPLATE B LINES UP T A W LL LE A WITH CENTERLINE ON CURB DIAGRAM A USE LEVEL TO MAKE SURE TEMPLATE IS PLUMB AND MARK HOLES AND DRILL DIAGRAM B AND C REPEAT STEP FOR OPPOSITE WALL LEFT WALL B B NOTE ENSURE YOU MARK CORRECT HEIGHT FOR YOUR UNIT EITHER 66 OR 78 1 4 C A 5

STEP 3 INSERT BUMPER BLOCKS INTO WALL BRACKETS A FOR CONFIGURATIONS WITH SHOWER HEAD TO THE LEFT INSERT BUMPER BLOCKS INTO WALL BRACKETS AS SHOWN 5 8 BUMPER 1 4 BUMPER 1 4 5 8 1 4 5 8 B FOR CONFIGURATIONS WITH SHOWER HEAD TO THE RIGHT INSERT BUMPER BLOCKS INTO WALL BRACKETS AS SHOWN 1 4 BUMPER 5 8 BUMPER 5 8 5 8 1 4 1 4 6

STEP 4 INSTALL WALL BRACKETS ON LEFT AND RIGHT WALL AS SHOWN 3 10A 10A 12 3 12 11 11 STEP 5 INSTALLING BOTTOM WATER DIVERTER PLACE THE PANEL ON CARBOARD BOX TO INSTALL THE BOTTOM GASKET 18 INTERIOR SHOWER SIDE 18 INTERIOR SIDE EXTERIOR SIDE 6 6 7

STEP 6 INSTALLING ROLLERS 18 18 15 NOTE DO NOT INSTALL ROLLER CAP AT THIS POINT Eccentric nut for roller adjustment Raises and lowers the roller Minimum spacing should be oriented towards the middle as shown Adjustments can be made after the door installation STEP 7 VERIFY ROLLERS AND PLASTIC WATER DIVERTER ARE INSTALLED PROPERLY AND LEAN DOOR AGAINST BACK WALL INSIDE SHOWER 18 18 15 INTERIOR SIDE EXTERIOR SIDE BACK WALL INTERIOR SIDE EXTERIOR SIDE 6 SIDE VIEW 8

STEP 8 INSTALL TRACK A SLIDE WALL BRACKET SLEEVES ONTO BOTH ENDS OF TRACK AS PER ILLUSTRATION 10B 10B 13 13 B SLIDE WALL BRACKETS SLEEVES ONTO EACH WALL BRACKET AS PER THE ILLUSTRATION TIGHTEN BACK SET SCREWS ONLY 10A 10A 10B 10B 13 13 C CONFIRM THE TRACK IS POSITIONED PROPERLY BY ENSURING WARNING LINES AT BOTH ENDS OF THE TRACK ARE NOT VISIBLE AS PER THE ILLUSTRATION ONCE IN PROPER POSITION TIGHTEN FRONT SET SCREW ENSURE WARNING LINES ARE NOT VISIBLE WRONG CORRECT WARNING LINES WARNING LINES 10A 10A 10B 9 13 10A 10B 13 10B 13

STEP 9 INSTALLING ALUMINUM BOTTOM CHANNEL LINE UP CENTERLINE ON TEMPLATE C L WITH CENTERLINE ON CURB PEEL OFF TABS AND STICK TEMPLATE ONTO CURB DIAGRAM A B AND C NOTE FOR LEFT DOOR CONFIGURATION USE TEMPLATE C R WALL CURB CENTERLINE PEEL OFF TWO WAY TAPE ON U CHANNEL DIAGRAM D PLACE ON CURB USING TEMPLATE AS GUIDE DIAGRAM E OVERHEAD VIEW OVERHEAD VIEW CENTERLINE CENTERLINE CENTERLINE LEFT SIDE NOTE MAKE SURE TEMPLATE TOUCHES WALL A RIGHT SIDE B C 1 CENTERLINE 1 D E 10

STEP 10 INSTALLING FIXED PANEL 1 1 8 ION SH U C 1 4 19 PLACE 1 4 PROVIDED CUSHIONS ON EACH SIDE OF U CHANNEL AS SHOWN SET FIXED PANEL ONTO CUSHIONS AND SLIDE PANEL GENTLY UNTIL TOUCHING SIDE WALL CHECK FOR ALIGNMENT OF GLASS AND SIDE WALL IF GLASS DOES NOT ALIGN WALL GO TO STEP 10A OR 10B TO ADJUST PANEL IF IT IS ALIGNED GO TO STEP 11 11

STEP 10A ALIGNING FIXED PANEL WITH SIDE WALL EXAMPLE 1 1 B GAP AT TOP A ADD ADDITIONAL CUSHIONS TO U CHANNEL ON SIDE A TO CLOSE GAP B 2 B A NOTE ADDITIONAL CUSHIONS PROVIDED IN INSTALLER KIT A 12

STEP 10B ALIGNING FIXED PANEL WITH SIDE WALL EXAMPLE 2 1 GAP AT B BOTTOM A ADD ADDITIONAL CUSHIONS TO U CHANNEL ON SIDE A TO CLOSE GAP B 2 B A NOTE ADDITIONAL CUSHIONS PROVIDED IN INSTALLER KIT A 13

STEP 11 INSTALLING FIXED PANEL HOLDERS INTERIOR SHOWER SIDE 14 16 Glass Holder NOTE DO NOT INSTALL FIXED PANEL HOLDER S CAP AT THIS POINT MAX MIN Eccentric nut for glass holder adjustment Raises and lowers the glass holder Minimum spacing should be oriented towards the middle as shown Adjustments can be made after the door installation TO LEVEL TRACK ADJUST FIXED PANEL HOLDERS BY ROTATING DIAGRAM A ONCE LEVEL HOLD IN PLACE AND TIGHTEN SCREW DIAGRAM B AND C THEN INSTALL CAP DIAGRAM D 13 13 14 A B C D NOTE HOLD IN PLACE WITH ALLEN WRENCH WHEN TIGHTENING SCREW 14

STEP 12 INSTALLING BOTTOM GUIDE PLACE GUIDE ON CURB AND MARK HOLES FOR DRILLING DIAGRAM A DRILL HOLES DIAGRAM B INSTALL GUIDE DIAGRAM C AND D 16 1 4 2 A B 16 4 3 2 C D STEP 13 HANG DOOR NOTE IF DOOR ALIGNS PROPERLY WITH SIDE WALL INSTALL ROLLER CAPS AND GO TO STEP 14 IF NOT REFER TO STEP 13A 18 15 INTERIOR SHOWER SIDE 13 18 16 2 15

STEP 13A ALIGNING DOOR TO WALL ROTATE ROLLERS TO CLOSE GAP USING PROVIDED ALLEN WRENCH AS SHOWN DIAGRAM A ONCE ALIGNED TIGHTEN ROLLER SCREW AND INSTALL ROLLER CAP DIAGRAM B AND C EXTERIOR VIEW 18 15 13 15 13 15 A B NOTE LOOSEN SCREW 1 TO 2 NOTE HOLD ALLEN WRENCH TURN TO RELEASE PRESSURE IN PLACE WHEN TIGHTENING SCREW C INTERIOR VIEW 16

STEP 14 INSTALL BOTTOM ROLLERS INSTALL BOTTOM ROLLERS DIAGRAM A ADJUST BOTTOM ROLLERS TO TOUCH BOTTOM OF TRACK BY ROTATING ROLLER AS SHOWN DIAGRAM B AND C ONCE ALIGNED TIGHTEN ROLLER SCREW AND INSTALL ROLLER CAP DIAGRAM D AND E Eccentric nut for roller adjustment Raises and lowers the roller Minimum spacing should be oriented towards the middle as shown for all rollers and pins 18 18 16 15 15 13 13 14 13 14 SIDE VIEW A B NOTE LOOSEN SCREW 1 C TO 2 TURNS TO RELEASE PRESSURE 18 15 13 14 NOTE HOLD ALLEN WRENCH D IN PLACE WHEN TIGHTENING SCREW 17 E

STEP 15 FIT BOTTOM ALUMINUM WATER GUARD MEASURE OPENING BETWEEN BOTTOM GUIDE AND WALL AS PER BELOW ILLUSTRA TION DIAGRAM A CUT BOTTOM WATER GUARD TO YOUR MEASUREMENT DIAGRAM B PLACE ON CURB AND INSERT INTO BOTTOM GUIDE DIAGRAM C PLACE END BLOCK ON BOTTOM WATER GUARD DIAGRAM D ENSURE MEASUREMENT AT BOTH POINTS ARE THE SAME DIAGRAM E MARK LOCATION OF BOTTOM WATER GUARD DIAGRAM F 18 18 16 16 5 2 2 5 CU RB A B 7 2 C OVERHEAD VIEW 18 5 5 EQUAL DISTANCES D E F 18

STEP 16 INSTALL ALUMINUM WATER GUARD SET REMOVE BOTTOM WATER GUARD AND CORNER BLOCK PEEL OFF BACK OF STICKY TABS AND REINSTALL USING PENCIL MARKS AS GUIDE DIAGRAM A INSTALL LOWER BLOCK INSERT SIDE WALL WATER GUARD DO NOT REMOVE STICKY BACKING ON WATER GUARD AT THIS TIME DIAGRAM B PLUMB AND MARK TOP WITH PENCIL DIAGRAM C REMOVE STICKY TAB BACKING AND INSTALL WATER GUARD AND TOP BLOCK DIAGRAM D WIPE THE BASE WITH A CLEAN CLOTH BEFORE INSTALLING THE THRESHOLD 5 7 5 7 7 5 A B 18 18 13 13 7 5 7 5 C 19 D 5 7

STEP 17 INSTALL SEALS A INTERIOR SIDE B 18 DOOR PANEL 16 17 A B FIXED PANEL EXTERIOR SIDE STEP 18 INSTALL HANDLE PLASTIC BUSHING WASHER 8 18 5 8 KNOB 1 4 WASHER PLASTIC BUSHING TUBE PLASTIC WASHER 20

STEP 19 APPLYING SILICONE A WIPE DOWN AREAS SHOWN WITH CLEAN CLOTH AND DENATURED OR ISOPROPYL ALCOHOL INTERIOR AND EXTERIOR WIPE THE BASE WITH A CLEAN CLOTH TO ENSURE SURFACE HAS NO DEBRIS B TAPE OFF AREAS SHOWN WITH PAINTERS TAPE INTERIOR AND EXTERIOR 1 16 1 8 ON METAL SIDE PAINTERS TAPE 1 16 1 8 ON TILE SIDE 21

STEP 19 CONTINUED APPLYING SILICONE C CUT OFF TIP OF CAULKING TUBE AT AN ANGLE 45 1 4 D APPLY CAULKING AS SHOWN ENSURE CAULKING IS ADDED TO AREAS REPRESENTED BY THE DOTTED LINE 22

STEP 19 CONTINUED APPLYING SILICONE E TOOL WITH PROVIDED SEALING FINISHING TOOL F REMOVE TAPE 23

G LET CAULKING CURE FOR 48 HOURS 48 HOURS 24