Return to flip book view

INSTALLATION INSTRUCTIONS REGENCY THIS SHOWER IS PRE CUT TO FIT 57 TO 58 02 02 18 Rev 1 0

CONFIGURATIONS THIS CONFIGURATION IS ILLUSTRATED IN THIS MANUAL NOTE THE REGENCY ENCLOSURE IS REVERSIBLE FOR LEFT OR RIGHT HAND INSTALLATION THIS MANUAL WILL SHOW THE LEFT HAND INSTALLATION FOR RIGHT HAND INSTALLATION SIMPLY BEGIN ON THE OPPOSITE WALL AND REVERSE THE ORIENTATION OF THE PARTS AS NECESSARY 1

Assembly Drawing 11 10 8 4 5 2 1 11 13 7 5 1 10 5 1 13 11 5 9 13 6A 12 1 13 6B PACKING LIST PART DESCRIPTION Q TY PART 9 1 Wall Plugs 4pcs 2 Wall Channel 1pc 3 Door Panel 1pc 4 Fixed Panel 1pc 5 S crews ST4x1 4pcs 6A Bottom Bracket x1 Wall Plugs x1 1set DESCRIPTION Bottom Door Gasket Q TY 1pc Hinges x2 10 Wall Plugs x8 2sets Screws ST5x2 x8 11 Gaskets B 3pcs 12 Transparent Acrylic Threshold 1pc 13 1 8 Cusions 2pcs 14 Hinge Shim 2pcs 15 Installation Kit 1set 6B Screws ST4x1 x1 7 Handle 1pc 8 Gasket A 1pc 2

Inspect the product immediately upon receipt for transit damage missing parts or manufacturing defects Handle the product with care Do not set on hard surface and protect all edges and corners from impact Tempered glass is up to 4 times stronger than annealed glass but edges and corners can be very fragile Si lic on e Notes read these instructions carefully before start of installation Special care should be taken when drilling walls to avoid hidden pipes or electrical cables Note This product is heavy and may require two people to install 2 PHILLIPS INSTALLATION KIT 15 1 4 1 2 Setting Blocks 3 Masonry Bits 1 32 Sealant Finishing Tool Allen Wrenches 1 8 Cushions Painters Tape

STEP 1 FINDING CENTERLINE TO FIND CENTERLINE PLACE TEMPLATE ON CURB AND MATCH NUMBERS ON 3 3 2 2 1 1 1 1 2 2 3 3 4 12 15 9 6 3 3 6 9 15 12 5 4 4 4 CENTERLINE WALL CURB 5 12 15 9 6 3 6 9 15 12 12 15 12 15 9 9 6 6 3 3 3 3 6 6 9 9 CURB 15 12 15 12 3 FRONT AND BACK EDGES OF CURB AND MARK CENTERLINE 4

STEP 2 INSTALLING WALL CHANNEL A 2 LINE UP CENTER OF VERTICAL WALL CHANNEL WITH CENTERLINE ON CURB PLUMB AND MARK FOR HOLES DIAGRAM A DRILL HOLES WITH 1 4 DRILL BIT AT LEAST 2 DEEP DIAGRAM B AND C INSTALL PLUGS AND SCREWS 1 4 DIAGRAM D STUD TILE BACKING 1 4 HOLE TILE B C 2 2 5 1 D 5

STEP 3 SETTING FIXED PANEL PLACE 1 8 CUSHIONS ONTO CURB DIAGRAM A PLACE FIXED PANEL ONTO CUSHIONS AND SLIDE INTO VERTICAL WALL CHANNEL DIAGRAM B LEAVE A 28 3 8 OPENING FROM BOTTOM EDGE OF FIXED PANEL TO BOTTOM CORNER OF WALL DIAGRAM C 2 22 13 A 1 8 CUSHIONS 13 2 4 2 2 B 28 3 8 2 4 C 28 3 8 6

STEP 4 INSTALL CLAMP CENTER FIXED PANEL ON THRESHOLD BY ENSURING MEASUREMENTS AT BOTH POINTS ARE THE SAME DIAGRAM A MARK HOLE LOCATION FOR CLAMP DIAGRAM B ANGLE GLASS TOWARDS OUTER EDGE OF CURB TO ALLOW ADEQUATE SPACE FOR DRILLING DIAGRAM C NEXT INSTALL CLAMP ONTO CURB DIAGRAM D RE POSITION GLASS TO CENTERLINE ON THRESHOLD AGAINST CLAMP AND INSTALL CLAMP COVER PLATE DIAGRAM E A OVERHEAD VIEW 4 EQUAL DISTANCES 4 B 2 6A C D OVERHEAD VIEW 1 4 4 7 4 E 6A 4

STEP 5 CONFIRM DOOR OPENING WIDTH CONFIRM BOTH MEASUREMENTS ARE 28 3 8 AT TOP AND BOTTOM TO ENSURE ADEQUATE SPACING FOR DOOR IF MEASUREMENTS ARE 28 3 8 GO TO STEP 6 IF NOT REFER TO STEP 5A OR 5B 28 3 8 28 3 8 STEP 5A ADJUSTING FIXED PANEL IF OVER 28 3 8 IF TOP WIDTH IS OVER 28 3 8 ADD CUSHIONS BENEATH FIXED PANEL AS SHOWN 4 22 OVER 28 3 8 ADD PROVIDED CUSHIONS TO ACHIEVE 28 3 8 OPENING NOTE ADDITIONAL CUSHIONS 28 3 8 PROVIDED IN INSTALLER KIT 8

STEP 5B ADJUSTING FIXED PANEL IF UNDER 28 3 8 IF TOP WIDTH IS UNDER 28 3 8 ADD CUSHIONS BENEATH FIXED PANEL AS SHOWN NOTE ADDITIONAL CUSHIONS PROVIDED IN INSTALLER KIT UNDER 28 3 8 4 ADD APPROPRIATE SIZE CUSHIONS FOR 28 3 8 OPENING 6 NOTE YOU MAY NEED TO LOOSEN SCREW ON CLAMP TO ALLOW RAISING GLASS HIGH ENOUGH TO FIT ADDITIONAL 28 3 8 CUSHION ONCE CORRECT SPACING IS REACHED TIGHTEN DOWN SCREW STEP 6 INSTALL HINGES ON DOOR ATTENTION NEVER SET YOUR GLASS DOWN DIRECTLY INSIDE ONTO A TILE OR CONCRETE FLOOR ALWAYS USE A PIECE OF WOOD OR 3 10 CARDBOARD AND LEAVE THE CORNER PADS ON THE GLASS UNTIL IT BECOMES NECESSARY TO REMOVE THEM TO PROTECT THE BOTTOM EDGE AND CORNERS FROM DAMAGE WHICH COULD LEAD TO BREAKAGE OUTSIDE 9

STEP 7 SETTING DOOR PLACE 1 2 SETTING BLOCKS ON CURB WHERE THE DOOR WILL REST AND PLACE THE DOOR ONTO THE SETTING BLOCKS AS SHOWN DIAGRAM A ENSURE DOOR LINES UP WITH STATIONARY PANEL BY CHECKING EVEN REVEAL DIAGRAM B REMOVE 1 PROTECTIVE CORNER AND SLIDE ON H PLASTIC TO KEEP DOOR AND PANEL ALIGNED WHEN MARKING HOLES FOR HINGES REMOVE C C A A NOTE HAVE SECOND PERSON INSIDE SHOWER TO ASSIST INSTALLING DOOR 3 OVERHEAD VIEW 10 1 2 BLOCKS 10 3 4 EQUAL DISTANCES A H PLASTIC B 10

STEP 8 CONFIRM HEIGHT OF DOOR ENSURE HEIGHT OF DOOR IS EVEN WITH HEIGHT OF FIXED PANEL 3 8 4 NOTE IF DOOR HEIGHT IS NOT EVEN WITH THE FIXED PANEL GO TO STEP 8A IF IT IS EVEN GO TO STEP 9 STEP 8A ADJUSTING DOOR HEIGHT ADD PROVIDED CUSHIONS UNTIL CORRECT HEIGHT IS ACHIEVED DIAGRAM B 3 A NOT EVEN 8 4 A ADD CUSHIONS 11 ADD PROVIDED CUSHIONS HERE B

STEP 9 INSTALL DOOR MARK HOLE LOCATIONS FOR HINGES DIAGRAM A DRILL HOLES WITH 1 4 DRILL BIT AT LEAST 2 DEEP DIAGRAM B AND C LASTLY INSTALL PLUGS SCREWS AND HINGE SHIM DIAGRAM D A B 10 1 4 STUD TILE 1 4 HOLE D TILE BACKING C 2 HINGE SHIMS SCREW ST5x2 STEP 10 INSTALL SEALS B C 3 A 9 11 3 B 8 3 H plasic A 4 C 4 NOTE DOOR SHOULD BE IN OPEN POSITION FOR THIS STEP VIEW FROM OUTSIDE 12

STEP 11 INSTALL HANDLE 7 13 3

STEP 12 INSTALL TRANSPARENT ACRYLIC THRESHOLD PLACE TRANSPARENT THRESHOLD ONTO CURB AND SLIDE IT UNDER THE DOOR UNTIL IT IS TOUCHING THE BOTTOM GASKET AND MARK POSITION DIAGRAM A AND B DO NOT PEEL TAPE BACKING AT THIS POINT OPEN DOOR AND REMOVE BOTTOM SEAL DIAGRAM C PEEL OFF TWO WAY TAPE ON TRANSPARENT THRESHOLD DIAGRAM D AND PLACE ONTO CURB DIAGRAM E APPLY A BEAD OF SILICONE ON EXTERIOR AND INTERIOR OF THRESHOLD DIAGRAM F RE INSTALL BOTTOM GASKET DIAGRAM G 3 9 12 12 MARK BOTH AREAS WITH PENCIL SIDE VIEW A B 12 3 9 C D 3 12 9 E F G NOTE LEAVE DOOR IN OPEN POSITION FOR 48 HOURS TO ALLOW SILICONE TO CURE 14

STEP 13 APPLYING SILICONE A WIPE DOWN AREAS SHOWN WITH CLEAN CLOTH AND DENATURED OR ISOPROPYL ALCOHOL INTERIOR AND EXTERIOR WIPE ALL SURFACE WITH A CLEAN CLOTH TO ENSURE AREAS TO BE SILICONED ARE FREE OF DEBRIS B TAPE OFF AREAS SHOWN WITH PAINTERS TAPE INTERIOR AND EXTERIOR 1 16 1 8 ON METAL SIDE PAINTERS TAPE 1 16 1 8 ON TILE SIDE 15

STEP 13 CONTINUED APPLYING SILICONE C CUT OFF TIP OF CAULKING TUBE AT AN ANGLE 45 1 4 D APPLY CAULKING AS SHOWN ENSURE CAULKING IS ADDED TO AREAS REPRESENTED BY THE DOTTED LINE INTERIOR AND EXTERIOR 16

STEP 13 CONTINUED APPLYING SILICONE E TOOL WITH PROVIDED SEALING FINISHING TOOL F REMOVE TAPE 17

STEP 13 CONTINUED APPLYING SILICONE G LET SILICONE CURE FOR 48 HOURS 48 HOURS 18